Denon-AVR1604-avr-sm维修电路原理图.pdf

《Denon-AVR1604-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR1604-avr-sm维修电路原理图.pdf（71页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL MODEL AVR-1604/684 AVC-1580 AV SURROUND RECEIVER / AMPLIFIER 16-11, YUSHIMA 3-CHOME, BUNKYO-KU, TOKYO 113-0034 JAPAN X0174V.02 DE/CDM 0311 For U.S.A., Canada, Europe, U.K., Asia, China,Taiwan R.O.C., Korea & Japan model 前、 必読。本機、火災、感電、 対安全性確保配慮 、法的電気用品安全法 、所定許可得製造。 従際、安全性維 持、記載 注意事項必守

2、。 本機仕様性能改良、予告変更 。 Please use this service manual with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. 修理際、必取扱説明書参照上、作業 行。 本文中使用、説明都合上 現物多少異場合。 補修用性能部品保有期間、製造打切後8年。 注意 For purposes of improvement, specif

3、ications and design are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 2 2AVR1604/684 / AVC-1580 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer,

4、 make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. (1) (2) 500V 1M (1) (2) RadioFans.CN 收音机爱

5、好者资料库 3 3AVR-1604/684 / AVC-1580 CAUTION IN SERVICING Initializing AV SURROUND RECEIVERInitializing AV SURROUND RECEIVER AV SURROUND RECEIVER initialization should be performed when the mcom, peripheral parts of mcom, and DSP P.W.B. are replaced. 1.Switch off the unit and remove the AC cord from the

6、wall outlet. 2.Hold the following SPEAKER A button and SPEAK- ER B button, and plug the AC cord into the outlet. 3.Check that the entire display is flashing with aninterval of about 1 second, and release your fingersfrom the 2 buttons and the microprocessor will be initialized Note: Note: If step 3

7、does not work, start over from step 1. Alluser settings will be lost and this factorysetting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. 時注意事項 AV 初期化 AV 初期化 周辺部品、DSP 基板等交換場 合、AV 初期化行下。 1.電源押状態、 壁電源電源抜。 2.SPEAKER A SPE

8、AKER B 同時押 、電源差込 。 3. 表示約 1 秒間隔点滅 確認後、2 指離。 初期化。 注意 :注意 :上記 3 状態場合、一度操作 1 直。 初期化行客様設定内容工場出荷 状態戻、設定内容 控初期化後再設定。 4 4 AVR-1604/684 / AVC-1580 LEVEL DIAGRAMS FRONT/CENTR/SURROUND/SURROUND BACK 20dB 10dB 0dB (200mV) -10dB -20dB 6CH IN 40dB 30dB 0dB (200mV) -10dB -20dB -12dB 6CH IN CD IN -10dBFS -30dBFS -

9、20dBFS 6CH IN CENTER SURROUND SURROUND-BACK 6CH IN -10dBFS -20dBFS -30dBFS 6dB D/A OUT 100mV REF DSP OUTD/A+ MUTE DSP OUTD/A+ 6dB D/A -10dBFS 0dBFS -20dBFS -30dBFS MUTE D/A OUT 100mV REF CENTER SL/SR/SB FRONT 40dB 30dB 20dB 10dB A/D- -+ A/D 0dBFS CD IN 6CH IN A/D IN REV AMP A/D IN REV AMP A/D IN REV

10、 AMP INPUT BUFFER AMP DIR DIGITAL D/A OUT LPF REV AMP SW SUM REV AMP + HPF MUTE DSPD/A- - - SUM S/W + D/A 0dBFS BD3811K1 + MUTE POWER AMPTONEPRE AMP ELECTRIC VOLUME SPK OUT FRONT 2.83V (1W/8ohm) SPK OUT FRONT ATTH/P OUT MUTE -18dB15.5dB VOL 00 MUTE -18dB BD3811K1 BD3812F + + 15.5dB VOL 00 -35.5dB H/

11、P OUT 47mV (0.27W 8ohm) SPK OUT CENTER SURROUND SPK OUT SURROUND BACK 25.5dB SPK OUT 2.83V (1W/8ohm) 25.5dB 5 5 AVR-1604/684 / AVC-1580 SUB WOORER 6dB Config1-38dBFS (112mV) (200mV) -5dB -30dB -20dB -10dB 30dB 20dB 10dB OdB D/A -10dBFS 0dBFS 6dB 6dB 10.5dB 6CH IN -20dBFS -30dBFS Config2-25dBFS LFE L

12、FE Front D/A Out 200mV ref D/A+ MUTE SUB_WOOFER - - -DSP OUT D/A OUT LPF SW SUM REV AMP REV AMP 6CH INPUT + MUTE ELECTRIC VOLUME PRE AMP SUB WOOFER PRE OUT BD3811K1 SUB WOOFER PRE OUT 150mV TO FRONT CH -18dB VOL 00 27.5(15.5+6+6)dB 6 6 AVR-1604/684 / AVC-1580 BLOCK DIAGRAM LOOP FILTER FM FRONTEND TU

13、NER SR SL SW C FR FL TUNERPART FM ANT AM ANT 6CH_EX_INPUT IF AMP IF FILTERIF FILTER IF IC FM & AM AM TUNING PLL CIRCUIT FROM u-COM MUTING L.P.F MPX IC FRONT IN OPTICAL 3 V.AUX L/R V.AUX VIDEO ANALOG IN CDR/TAPE ANALOG IN CD VCR CDR/TAPE TV/DBS DVD/VDP AUX VCR ANALOGOUT ADC ADC HPF BD3811K1 ALRCK SER

14、IAL DATA COUT MCLK I/O PORT DSDATA1 ASDATA ABCLK DIGITAL FILTER DIGITAL FILTER DIGITAL FILTER VOLUME VOLUME VOLUME DIGITAL FILTER DIGITAL FILTER SDOUT VOLUME DIGITAL FILTER DIGITAL FILTER VOLUME VOLUME AUDIO CODEC AD1837 DIGITAL FILTER DIGITAL FILTER VOLUME DIGITAL FILTER VOLUME INPUT SELECTOR & VOL

15、UME DVD/VDP TV/DBS VCR + +DAC DAC DAC - VIDEO INPUTMUTE + + DAC DAC + + + DAC DAC DAC - - EX_C CENTER EX_SR SR SW ANA_IN DSP_FR EX_FR - DSP_FL EX_FL SL EX_SL - +12V - EX_SW 2CH-VOLUME IC BD3812F MICOM, FLT DRV ENCODER DIR CODEC DSP RMC_IN/OUT +2.5V +3.3V CXA1511M RMC IN/OUT DVD/VDP TV/DBS MONITOR OU

16、T COMPONENT VIDEO INPUT ( Y, B-Y, R-Y )BA7625*1,BA7626*2 VIDEO SWITCH VIDEO SWITCH LA7952*1 ( C, Y )LA7952*2 VIDEO SWITCH DVD/VDP TV/DBS VCR S-VIDEO INPUT VCR OUT MONITOR OUT VCR OUT MONITOR OUT +12V OP AMP INPUT/VOL +5V A/D POWER RELAY VIDEO 7812 7805 MAIN +B OP AMP INPUT/VOL TUNER DATA IN (REMOCON

17、) +5.6V(CPU) 7805 COMPONENT SEL1/2 -VKK MAIN -B -36V DAC DIGITAL FILTER INPUT DIGITAL IN OPTICAL 2 OPTICAL 1 COAXIAL Selector X-TAL OPTICAL DIGITALOUT ROM 512k X 8 RAM 64k X 16 RDATA(21) XMCK FROM MICOMCLATCH CIN CCLK DIR DeModulate Lock Detect & DATA Selector fs 64fs 256fs LC89057W-VF4 DT0(56) 74LV

18、244 BUFFER DATA 256fs 64fs 64fs fs DR1 CLKIN (32) DR0 fs FL/FR/C SL/SR CONTROLPORT MUTE SWF MIXING TCLK1(65) RCLK1(68) RFS3(41) RFS1(69) RCLK0(61) TCLK0(57) TCLK2(47) SW/SB CLOCK RESET DSP DIGITAL AUDIO DECODER MELODY 32 AVC1570X / AVR1604 BLOCK DIAGRAM SCDIN INTREQ SCDIO SCCLK CS FROM MICOM KEY_MAT

19、RIXRESONATOR 12MHz ANA_IN DATA TUNER PLL DATA FLT DRIVERMICOM CXP740096 PART DATA DTS/DD/PL II BD3811K1 + FL DRIVER + LC75721NE + FL DISPLAY 16-ST-42GNK + FR - SPK B FL FR + - - + + SPK A FL - + + - H/P OUT 7915 7815 AC OUTLET 7805 FILAMENT AC 7805 + MUTE + + + + + + + + - + - + - SURR R SURR L - +

20、CENTER SURR BACK SPEAKEROUT AC CORD PRE OUT SUB WOOFER 7 7AVR-1604/684 / AVC-1580 ADJUSTMENT Tuner Section (AVR-1804/884 only) CONNECTION DIAGRAM OF MEASURING INSTRUMENTS ? FM STEREO MODULATOR FM SSG Digital Voltmeter 75ohm T402T403 IC402 VR402 TUNER BD R471 20+14 10dB ? AM T402T403 IC402 TUNER BD R

21、471 VR401 FM ALIGNMENT InputOutputAdjustment Step Alignment Item Tuning Frequency Setting TypeFrequency Input Level ModulationCouplingTypeConnect toPointsAdjust to 1 Center Adjustment 98.1MHz (98.0MHz) FM SSG98.1MHz60dB Mono 1kHz 100% Antenna Terminal Digital Voltmeter R471T402 50mV 2Distortion 98.1

22、MHz (98.0MHz) FM SSG98.1MHz60dB Mono 1kHz 100% Antenna Terminal Distortion Meter Output Terminal (L) T403 Minimum Distortion 3Repeat Steps 1 and 2 4Signal Level 98.1MHz (98.0MHz) FM SSG98.1MHz20dBOFF Antenna Terminal Light “TUNED” on FL Display VR402 AM ALIGNMENT OutputAdjustment Step Alignment Item

23、 FrequencyInput TypeConnect toPointsAdjust to Remarks 1Signal Level 999 (1000) kHz AM SSGVR401 Light “TUNED” on FL Display SSG OUTPUT 74dB (EMF) 8 8AVR-1604/684 / AVC-1580 Audio Section Idling Current Required measurement equipment : DC Voltmeter 調整必要測定器 : 直流電圧計 Preparation (1)Avoid direct blow from

24、 an air conditioner or an electric fan, and adjust the unit at normal room tempereture 15 C 30 C (59 F 86 F). (2)Presetting POWER (Power sourse switch)OFF SPEAKER (Speaker terminal)No load (Do not connect speaker, dummy resistor, etc.) (1)、扇風機風通良場所避、通常使用状態置。周囲温度 1530、湿度常湿。 Adjustment (1)Remove top c

25、over and set VR101, VR102, VR103, VR104, VR105 on Amp. Unit, VR106 on SURR.-BACK ch Amp. Unit at full counterclockwise ( ) position. (2)Connect DC Voltmeter to test points (FRONT-Lch: TP104, FRONT-Rch: TP105, CENTER ch: TP103, SURROUND-Lch: TP101, SURROUND-Rch: TP102, SURROUND-BACK ch: CP106). (3)Co

26、nnect power cord to AC Line, and turn power switch ON. (4)Presetting.MASTER VOLUME : - counterclockwise ( min.) MODE: 6CH STEREO FUNCTION: CD (5)Within 2 minutes after the power on, turn VR101 clockwise ( ) to adjust the TEST POINT voltage to 1.5 mV 0.5 mV DC. (6)After 10 minutes from the preset abo

27、ve, turn VR101 to set the voltage to 2.5 mV 0.5 mV DC. (7)Adjust the Variable Resistors of other channels in the same way. (1)上、基板VR101, VR102, VR103, VR104,VR105 及Surr. Back 基板VR106 反時計方向 () 回切状態。 (2) (FRONT-Lch: TP104, FRONT-Rch: TP105, CENTER ch: TP103, SURROUND-Lch: TP101, SURROUND-Rch: TP102, S

28、URROUND-BACK ch: CP106) 直流電圧計接続。 (3)電源AC100V （95105V 範囲可）接続、電源ON 。 (4)後、次。 VOLUME（音量調節）反時計方向 () 回、最小状態。 SPEAKER-A（端子）無負荷（、抵抗器接続。） MODE : 6CH STEREO FUNCTION : CD (5)2分以内VR101 時計方向 () 回電圧次調整。 1.5mV 0.5mV DC (6)予備調整10分後VR101 回、次電圧設定。 2.5mV 0.5mV DC (7)同方法各可変抵抗調整。 VR104 TR104 VR105 TP105 VR106 CP106 S

29、Back ch S Rch VR102 TP102 VR103,TP103 C ch VR101,TP101 F Lch S Lch F Rch DC Voltmeter 9 9AVR-1604/684 / AVC-1580 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主半導体記載。汎用半導体記載省略。 ? ? ? ? ? ICs CXP740096 (IC201) PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 PK7/

30、TO1 RST VSS XTAL EXTAL PK6/CS0 PK5/SI0 PK4/SO0 PK3/SCK0 PF7/AN11 PF6/AN10 PF5/AN9 PC6 PC7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 NC VDD VSS PK1/TX PK2/TEX PI1/RMC PI2/NMI PI3/TO0/ADJ PI4/INT1/CS1 PI5/SCK1 PC5 PC4 PC3 PC2 PC1 PC0 PB7/SI2 PB6/SO2 PB5/SCK2 PB4/TO2 PB3 PB2 PB1 PB0 PJ7 PJ6 PJ5 PJ4 PJ3 PJ2 PJ1 P

31、J0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 PI6/SO1 PI7/SI1 PE0/INT0 PE1/INT2 PE2/PWM0 PE3/PWM1 PE4 PE5 PE6 PE7 PG0/TxD PG1/RxD PG2/EC0 PG3/EC1 PG4/EC2 PG5/INT3 PG6/INT4 PG7/CINT AN0 AN1 AN2 AN3 PF0/AN4 PF1/AN5 PF2/AN6 PF3/AN7 AVDD AVREF AVSS PF4/AN8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 31 32 3

32、3 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 21 22 23 24 25 26 27 28 29 30 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 TOP VIEW CXP740096 Terminal Function 13811K1MUTEOBD3811K1 CONTROL

33、23811K1CLKOBD3811K1 CONTROL 33811K1DATAOBD3811K1 CONTROL 4CDR/TAPEOCDR/TAPE INHIBIT 5VCROVCR INHIBIT 6ERR MUTEOERR MUTE 7ERR MUTE OFFOERR MUTE OFF 889057 AUDIOILC89057 CONTROL 989057 EMPHAILC89057 CONTROL 10SW SUMOSW SUMMING CONTROL 11M32 SDINIDATA INPUT FROM MELODY32 1289057 SDINIDATA INPUT FROM LC

34、89057 13EPROM RESETOEPROM RESET 1489057 RESETOLC89057 RESET 15M32 CSOMELODY32 CS 16M32 SDOUTOMELODY32 CONTROL DATA 1789057 CEOLC89057 CE 1889057 SDOUTOCONTROL DATA 1989057 SCLKOCONTROL CLOCK 201837 RESETOCODEC RESET OSURR. BACK RELAY21RELAY-SB 22SW MUTEOSW MUTE 23RELAY F-BOFRONT B RELAY Pin No. Pin

35、NameFunctionI/O 10 10AVR-1604/684 / AVC-1580 Pin No. Pin NameFunctionI/O 24RELAY F-AOFRONT A RELAY 25RELAY SURROSURROUND RELAY 26RELAY CNTOCENTER RELAY 27RELAY H/POH/P RELAY 28FUNC UPIENCODER INPUT(FUNCTION) 29H/P DETECTIH/P DETECT 33NC 30FUNC DOWNIENCODER INPUT(FUNCTION) 32CNT MUTEOCENTER MUTE 31SB

36、 MUTEOSURR. BACK MUTE 69FRONT MUTEOFRONT MUTE 34SURR MUTEOSURROUND MUTE 35NC 36NC 37NC 38FL DRV RESETOLC75721NE RESET 39RELAY POWEROPOWER RELAY 40RESETIRESET 41GNDI 42XTAL 43EXTAL 44FL DRV CEOLC75721NE CE 45FL DRV DATAOLC75721NE DATA 46FL DRV/2090 CLKOCONTROL CLOCK 472090 DATAOBU2090F DATA 48VOL DOW

37、NIENCODER INPUT(VOLUME) 49VOL UPIENCODER INPUT(VOLUME) 50SEL DOWNIENCODER INPUT(SELECT) 51SEL UPIENCODER INPUT(SELECT) 52AVSS 53VREF 54AVDD 55NC 56GND 57STEP OPTIAREA SELECT 58SET OPTIMODEL SELECT 59GND 60KEY IN3IKEY INPUT 61KEY IN2IKEY INPUT 62KEY IN1IKEY INPUT 639K/10K STEPITUNER STEP SELECT 64PRO

38、TECTIPROTECTION 6589057 INTILC89057 INTERUPT 66M32 SCLKOMELODY32 CLOCK 671837 CEOCODEC CE 68M32 RESETOMELODY32 RESET 70NC 71NC 72NC 73NC 74NC 75NC 76NC 11 11AVR-1604/684 / AVC-1580 Pin No. Pin NameFunctionI/O 77PWR DOWNIPOWER DOWN DETECT 78RDS CLKOTDA7330 CONTROL CLOCK 79RDS DATAOTDA7330 CONTROL DAT

39、A 80NC 81VIDEO MUTEOVIDEO MUTE 82M32 INTREQI/OMELODY32 CONTROL 83VIDEO SEL1OVIDEO SELECT1 84VIDEO SEL2OVIDEO SELECT2 85REMOCONIREMOTE CONTROL SIGNAL INPUT 86GND 87GND 88VSS 89VDD 90NC 91NC 92PLL DATAOPLL CONTROL 93PLL CLKOPLL CONTROL 94PLL DT INOPLL CONTROL 95TU MUTEOTUNER MUTE 96STEREOISTEREO DETEC

40、T 97TUNEDITUNED DETECT 98PLL CEOPLL CONTROL 99NC 100 NC 12 12AVR-1604/684 / AVC-1580 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 2526 80797877767574737271706968676665 2728293031323334353637383940 5.1ch Mode SW

41、2 DVD 5.1ch Mode SW1 5.1ch Mode SW2 DSP BASS BOOST LOGIC TNF2 TNF1 BNF11 BNF21 BNF12 BNF22 BBNF2 OUT2 BBNF1 OUT1 AGND8 AGND7 VCC AGND6 VEE AGND5 MUTE CL DA DGND AGND4 GOUTSR VINSR AGND3 IN22 IN21 IN12 IN11 ROUT32 ROUT31 ROUT22 ROUT21 ROUT12 ROUT11 AGND10 GOUT2 VIN2 AGND9 GOUT1 VIN1 IN31 IN32 IN41 IN

42、42 IN51 IN52 IN61 IN62 IN71 IN72 IN81 IN82 INDVDSR INDVDSL INDVDC INDVDSW OUT2(+) OUT2(-) OUT1(+) OUT1(-) IN1DSP IN1MIX IN2DSP IN2MIX INDSPSR INDSPSL INDSPC INDSPSW AGND1 GOUTSW VINSW AGND2 GOUTC VINC OUTSW OUTC OUTSL OUTSR VINSL GOUTSL TREBLE BASS BD3811K1 (IC701) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1

43、5 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A15 A14 A13 A12 A11 CE I/O0 I/O1 I/O2 I/O3 Vcc GND I/O4 I/O5 I/O6 I/O7 WE A10 A9 A8 A7 NC A0 A1 A2 OE UB LB I/O15 I/O14 I/O13 I/O12 GND Vcc I/O11 I/O10 I/O9 I/O8 NC A3 A4 A5 A6 NC A0-A15 CE OE WE 64K x 16 MEMORY

44、 ARRAY DECODER COLUMN I/O CONTROL CIRCUIT GND VCC I/O DATA CIRCUIT I/O0-I/O7 Lower Byte I/O8-I/O15 Upper Byte UB LB CE OE WE LB UB PIN DESCRIPTION Pin Name Address inputs Symbol A0-A15 Data Inputs/OutputsI/O0-I/O15 Chip Enable Input Output Enable Input Write Enable Input Lower-byte Control (I/O0-I/O

45、7) Upper-byte Control (I/O8-I/O15) No ConnectionNC PowerVCC GroundGND IS61LV6416 (IC806) PIN DESCRIPTION Pin Name Address Inputs Symbol A0-A18 Data Input/Outputs, Command InputsDQ0-DQ7 Data Input/OutputsDQ8-DQ14 Data Input/Output or Address InputDQ15A-1 Chip Enable Output Enable Write Enable Reset/B

46、lock Temporary Unprotect Ready/Busy OutputRB Byte/Word OrganizationBYTE Supply VoltageVCC GroundVSS No Connected InternallyNC Dont Use as Internally ConnectedDU E G W RP A1A0 A2E A3VSS A4G A5DQ0 A6DQ8 A7DQ1 A17DQ9 A18DQ2 RBDQ10 NCDQ3 NCDQ11 RPVCC WDQ4 NCDQ12 NCDQ5 A8DQ13 A9DQ6 A10DQ14 A11DQ7 A12DQ15

47、A-1 A13VSS A14BYTE A15A16 24 13 12 1 25 36 37 48 M29W800T M29W800T 19 A0-A18 W DQ0-DQ14 M29W800AT E 15 G RP DQ15A-1 BYTE RB VCC Vss M29W800AT (IC805) 13 13AVR-1604/684 / AVC-1580 AD1837 (IC808) AD1837 Terminal Function DescriptionPin No.Pin Name Input/ Output 1,39DVDDDigital Power Supply. Connect to

48、 digital 5V supply. 2CLATCHILatch Input for Control Data 33CINISerial Control Input 4PD/RSTIPower-Down/Reset 5,10,16,24,30,35AGNDAnalog Ground 6,12,25,31NCNot connected 7,13,26,32OUTLxODACx Left Channel Output 8,14,27,33NCNot connected 9,15,28,34OUTRxODACx Right Channel Output 11,19,29AVDDAnalog Pow

49、er Supply. Connect to analog 5V supply. 17FILTDFilter Capacitor Connection. Recommend 10F/100nF. 18FILTRReference Filter Capacitor Connection. Recommended 10F/100nF. 20ADCLNIADC Left Channel Negative Input 21ADCLPIADC Left Channel Positive Input 22ADCRNIADC Right Channel Negative Input 23ADCRPIADC Right Channel Positive Input 36M/SIADC Master/Slave Select 37DLRCLKI/ODAC LR Clock 38DBCLKI/ODAC Bit Clock 40,52DGNDDigital Ground 41-44DSDATAxIDACx Input Data (Left and Right Supply) 45ABCLKI/OADC Bit Clock 46