Denon-AVR3310-avr-sm维修电路原理图.pdf

《Denon-AVR3310-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR3310-avr-sm维修电路原理图.pdf（211页珍藏版）》请在收音机爱好者资料库上搜索。

1、Denon Brand Company, D&M Holdings lnc. e X0425 V.04 DE/CDM 0909 SERVICE MANUAL AV SURROUND RECEIVER AV SURROUND AMPLIFIER MODELJPEUECE2E3E2AE1CEUT AVR-3310CI ? AVR-3310 ? ? AVR-990 ? ? MODELJPEUECE2E3E2AE1CEUT AVC-3310 ? ? s s s Ver. 4 For purposes of improvement, specifications and design are subje

2、ct to change without notice. Please use this service manual with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. Please refer to the MODIFICATION NOTICE. RadioFans.CN 收音机爱 好者资料库 2 AVR-3310CI/AVR-3310/AV

3、R990/AVC-3310 Please heed the points listed below during servicing and inspection. Heed the cautions! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cautions indicated

4、in the handling instructions. Caution concerning electric shock! (1) An AC voltage is impressed on this set, so touching in- ternal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servi

5、cing while the set is energized, un- plugging the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly! Though great care is taken when manufacturing parts from sheet metal, there m

6、ay in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. Only use designated parts! The sets parts have specific safety properties (fire resis- tance, voltage resistance, etc.). For replacement parts, be sure to

7、 use parts which have the same properties. In par- ticular, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the desig- nated parts. Be sure to mount parts and arrange the wires as they were originally! For safety reasons, some parts use tape, tubes

8、 or other in- sulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally.

9、Inspect for safety after servicing! Check that all screws, parts and wires removed or discon- nected for servicing have been put back in their original po- sitions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insu- lation check on the extern

10、al metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Us- ing a 500V insulation resistance tester, check th

11、at the in- sulation resistance between the terminals of the power plug and the externally exposed metal parts (antenna ter- minal, headphones terminal, microphone terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired. Concerning important safety part

12、s Many of the electric and structural parts used in the set have special safety properties. In most cases these prop- erties are difficult to distinguish by sight, and using re- placement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety perform

13、ance will be preserved. Parts with safety properties are indicated as shown below on the wiring dia- grams and parts lists is this service manual. Be sure to re- place them with parts with the designated part number. (1) Schematic diagrams . Indicated by the z mark. (2) Parts lists . Indicated by th

14、e z mark. Using parts other than the designated parts could result in electric shock, fires or other dangerous situations. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit t

15、o the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. CAUTION CAUTION RadioFans.C

16、N 收音机爱 好者资料库 3 AVR-3310CI/AVR-3310/AVR990/AVC-3310 DIMENSION AVR-3310CI/AVR-3310/AVR-990/AVC-3310 344 434 155 15.5 170.5 20.7 244.5 372.8 20.5 414 54.7 4 AVR-3310CI/AVR-3310/AVR990/AVC-3310 WIRE ARRANGEMENT If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure

17、to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. Wire arrangement viewed from the top Except AVR-3310CI, AVR-990 model sd Front Panel side Back Panel side 5 AVR-3310CI/AVR-3310/AVR990/AVC-3310 CAUTION I

18、N SERVICING Before the Digital P.W.B. are replaced If you cannot specify the cause of the digital PWB defect, carry out Initializing Update to latest firmware. The defect may be cleared. See the following for the method of initializing the com. Initializing AV SURROUND RECEIVER AV SURROUND RECEIVER

19、initialization should be performed when the com, peripheral parts of com, and Digital P.W.B. are replaced. 1. Switch off the unit. 2. Hold the following STANDARD button and DSP SIMULATION button, and switch on the unit. 3. Check that the entire display is flashing with an interval of about 1 second,

20、 and release your fingers from the 2 buttons and the microprocessor will be initialized. Note:If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring

21、after the initialization. JIG to use for servicing When you repair the printing board, you can use the following JIG. Please order to Denon Official Service Distributor in your region if necessary. Extention cable kit 00D SPK- 561 EXTENSION UNIT KIT : 1 Set 00D SPK- 562 TUCP CONN. JOINT KIT : 1 Set

22、Extention cable for Idling Current Parts Number for Extension Cables and Quantity of Unit. How to use and Adjust Idle Current. 1. The thin and hard plate (ex. Ruler) is fixed with the tape behind the cable. 2. The voltmeter is connected with the other side of the extension cable. 3. Refer to ADJUSTM

23、ENT(Idling Current). Parts NumberParts NameQty / unitRemarks 612050082004D6P 250mm NH1L=250mm 6P NH Cable 612050083007D8P 250mm NH1L=250mm 8P NH Cable 1,2 2,3 6 AVR-3310CI/AVR-3310/AVR990/AVC-3310 DISASSEMBLY Disassemble in order of the arrow of the figure of following flow. In the case of the re-as

24、sembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe attention of assembling it. TOP COVER DIGITAL UNIT ASSYFRONT PANEL UNIT ASSY Refer to DISASSEMBLYREG UNITRefer to DISASSEMBLY 2. DIGITAL UNIT ASSYRefer to DISASSEMBLY1.FRONT PANEL UNIT ASSY

25、 and EXPLODED VIEW5. REG UNITP.SW UNIT DIGITAL UNIT and EXPLODED VIEW (Ref. No. of EXPLODED VIEW : A-8) (Ref. No. of EXPLODED VIEW : G)REG UNIT FRONT USB UNIT (Ref. No. of EXPLODED VIEW : B-4) (Ref. No. of EXPLODED VIEW : E-3) REG CONNECT-1 UNITMIC UNIT BACK PANEL UNIT ASSY (Ref. No. of EXPLODED VIE

26、W : A-15) (Ref. No. of EXPLODED VIEW : A-9) Refer to DISASSEMBLYCONNECT UNIT-2FRONT IN UNIT 3. BACK PANEL UNIT ASSY (Ref. No. of EXPLODED VIEW : D-4) (Ref. No. of EXPLODED VIEW : A-10) PTC UNITVR CONNECT UNIT (Ref. No. of EXPLODED VIEW : A-5) A.VIDEO UNIT, A.AUDIO UNIT VOLUME UNIT and RADIATOR UNIT

27、ASSYSPEAKER UNIT (Ref. No. of EXPLODED VIEW : A-4) Refer to DISASSEMBLYRefer to DISASSEMBLYFUNC CONNECT UNIT 4. A.VIDEO UNIT, A.AUDIO UNIT6. AMP UNIT (Ref. No. of EXPLODED VIEW : A-7) and RADIATOR UNIT ASSYand EXPLODED VIEWFUNC UNIT and EXPLODED VIEWSPEAKER UNIT (Ref. No. of EXPLODED VIEW : A-6) A.V

28、IDEO UNIT (Ref. No. of EXPLODED VIEW : D-1)FLD UNIT (Ref. No. of EXPLODED VIEW : E-1) (Ref. No. of EXPLODED VIEW : A-1) A.AUDIO UNIT (Ref. No. of EXPLODED VIEW : E-2)AMP CONNECT UNIT MAIN CPU UNITRefer to DISASSEMBLY (Ref. No. of EXPLODED VIEW : F)7. AMP CONNECT UNIT REMOTE/IPOD UNITand EXPLODED VIE

29、W (Ref. No. of EXPLODED VIEW : B-5)AMP CONNECT UNIT 232C UNIT (Ref. No. of EXPLODED VIEW : D-2) (Ref. No. of EXPLODED VIEW : B-6) P.AMP UNIT Refer to DISASSEMBLY 9.P.AMP UNIT and EXPLODED VIEW P.AMP UNIT (Ref. No. of EXPLODED VIEW : C-17) d s d d 7 AVR-3310CI/AVR-3310/AVR990/AVC-3310 About the photo

30、s used for descriptions in the “DISASSEMBLY” section. The direction from which the photographs used herein were photographed is indicated at Direction of photograph: * at the left of the respective photographs. Refer to the table below for a description of the direction in which the photos were take

31、n. Photographs for which no direction is indicated were taken from above the product. 1. FRONT PANEL UNIT ASSY (1) Remove the screws. (2) Cut the wire clampers then disconnect the connector wires. Front side Direction of photograph: B Direction of photograph: DDirection of photograph: C Direction of

32、 photograph: A The viewpoint of each photograph (Photografy direction) View from above Except AVR-3310CI, AVR-990 model s d Proceeding:TOP COVER FRONT PANEL UNIT ASSY View from bottom d Except EUEC model cut cut CX021 CY052 Direction of photograph: D s 8 AVR-3310CI/AVR-3310/AVR990/AVC-3310 (3) Disco

33、nnect the FFC Cables. (4) Remove the screws Attention of assembling When mounting the FRONT PANEL ASSY on the CHASSIS, do so with the DOOR open so as to prevent breaking the EARTH PLATE(DOOR). If the FRONT PANEL ASSY is mounted on the chassis with the DOOR closed, the EARTH PLATE(DOOR) will hit the

34、CHASSIS and break. Direction of photograph: C FFC Cable ? ? dd s Please refer to EXPLODED VIEW for the disassembly method of each P.W.B included in FRONT PANEL ASSY. DOOR open DOOR closed (EARTH PLATE (DOOR) will be broken.) EARTH PLATE (DOOR) DOOR DOOR EARTH PLATE (DOOR) Direction of photograph: A

35、Direction of photograph: A d 9 AVR-3310CI/AVR-3310/AVR990/AVC-3310 2. DIGITAL UNIT ASSY (1) Remove the screws. (2) Remove the alminium tape, then cut the wire clampers. Disconnect the connector wire, FFC Cables, and board to board. 3. BACK PANEL UNIT ASSY Remove the Sheets, then remove the screws. P

36、roceeding:TOP COVERDIGITAL UNIT ASSY ? Direction of photograph: A Except EUEC modelFFC CableFFC Cable FFC Cable cut cut MAIN CPU UNIT DIGTAL UNIT ASSY Board to board CX047 CY052Alminium Tape s Proceeding:TOP COVERDIGITAL UNIT ASSY BACK PANEL UNIT ASSY Sheets View from bottom 10 AVR-3310CI/AVR-3310/A

37、VR990/AVC-3310 Remove the screws. ? ? Direction of photograph: A ? ? Direction of photograph: A EUEC model E2 model ? ? Direction of photograph: A E1C model s d 11 AVR-3310CI/AVR-3310/AVR990/AVC-3310 (3) Disconnect the connector wires and FFC Cable, then remove the screws. (4) Remove the PWB HOLDER.

38、 Disconnect the connector wire and FFC Cable. Except AVR-3310CI, AVR-990 model CX055CX074 Style pin : Loose Style pin : Loose Cord holder : Loose CX091 s d FFC Cable CX068 PWB HOLDER Direction of photograph: C d 12 AVR-3310CI/AVR-3310/AVR990/AVC-3310 4. A.VIDEO UNIT, AUDIO UNIT and RADIATOR UNIT ASS

39、Y (1) Disconnect the board to board and FFC Cable. (2) Disconnect the connector wires. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY d v Direction of photograph: C Direction of photograph: C MAIN CPU UNIT MAIN CPU UNIT FFC Cable CY034 E

40、xcept E1C model E1C model d CX073CX192 13 AVR-3310CI/AVR-3310/AVR990/AVC-3310 (3) Remove the screws. 5. REG UNIT (1) Disconnect the board to board and connector wires. Remove the Filament Tape. Direction of photograph: A A.VIDEO UNIT A.AUDIO UNIT RADIATOR UNIT ASSY Direction of photograph: A A.VIDEO

41、 UNIT E2 model EUEC model A.AUDIO UNIT RADIATOR UNIT ASSY s d d Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT d Board to board Direction of photograph: A CX231CX092 v Filament Tape HOTMELT 14 AVR-3310CI/AVR-3310/AVR990/AVC-3310

42、 (2) Disconnect the connector wires, then remove the screws. 6. SPEAKER UNIT (1) Disconnect the VH connector and conector. 7. AMP CONNECT UNIT (1) Disconnect the connector. PTC UNIT ? ? ? Direction of photograph: A s Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR U

43、NIT ASSY DIGITAL UNIT ASSY REG UNIT SPEAKER UNIT d CX851CX891 CX876 CX874 CX871 CX873 CX872 CX875 CX877 View from bottom Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT SPEAKER UNIT AMP CONNECT UNIT d CX803CX805 CX806CX811CX812CX

44、807 CX804 Direction of photograph: A s s 15 AVR-3310CI/AVR-3310/AVR990/AVC-3310 8. P.AMP UNIT (1) Remove the screws. Proceeding:TOP COVER BACK PANEL UNIT ASSY A.VIDEO UNIT, A.AUDIO UNIT and RADIATOR UNIT ASSY DIGITAL UNIT ASSY REG UNIT P.AMP UNIT SPEAKER UNIT AMP CONNECT UNIT d Direction of photogra

45、ph: B s 16 AVR-3310CI/AVR-3310/AVR990/AVC-3310 SPECIAL MODE Special mode setting button Press the ON/OFF button to turn on while pressing both buttons A and B at the same time. Note: If is displayed on the fluorescent display, the unit is set to the special developers mode and RS-232C com- municatio

46、ns are not possible. Press and hold in the STATUS and buttons for over 3 seconds with the power turned on to turn the display off. RS-232C communications are now enabled. ModeButton AButton Bcontents Version display (com/DSP Error Display) STATUSRETURN Serial No. and firmware versions such as Main,

47、Sub, DSP are displayed in the FL manager. Errors are displayed when they occur. (Refer to 16 page.) Displaying the protection history modeSTATUSMENU Displaying the protection history (Refer to 18 page.) Initialization mode (Remove settings for Installer Setup.) STANDARD DSP SIMULATION Backup data in

48、itialization is carried out. (Remove settings for Installer Setup.) Initialization mode (Includes settings for Installer Setup) CURSOR UP CURSOR DOWN Backup data initialization is carried out. (Includes settings for Installer Setup) Mode for switching tuner frequency stepSTANDARD DIRECT/ STEREO -E2

49、model only- Change tuner frequency step to FM:200kHz/AM:10kHzSTEP. Mode for preventing remote control acceptance STATUSENTER Operations using remote control are rejected. (Mode cancellation: Turn off power and execute the same button operations as when performing setup.) Panel lock mode DSP SIMULATION ZONE2 Operations using main unit panel buttons or master volume are rejected. Panel lock mode (Remove Master volume) DIRECT/ STEREO ZONE2Operations using main unit panel buttons are rejected. Cancellati