Denon-PMA720AEV14-int-sm维修电路原理图.pdf

《Denon-PMA720AEV14-int-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-PMA720AEV14-int-sm维修电路原理图.pdf（50页珍藏版）》请在收音机爱好者资料库上搜索。

1、D&M Holdings Inc. SERVICE MANUAL e e MODELJPE3E2EKEAE1CE1KCI PMA-720AEPP PMA-520AEPP INTEGRATED STEREO AMPLIFIER Ver. 14 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fai

2、l. For purposes of improvement, specifications and design are subject to change without notice. Please refer to the MODIFICATION NOTICE. RadioFans.CN 收音机爱 好者资料库 2 CONTENTS ABOUT THIS MANUAL .3 What you can do with this manual .3 Using Adobe Reader (Windows version) .4 SAFETY PRECAUTIONS .6 NOTE FOR

3、SCHEMATIC DIAGRAM .7 NOTE FOR PARTS LIST .7 TECHNICAL SPECIFICATIONS .8 DIMENSION .8 DISASSEMBLY .9 1. FRONT PANEL ASSY .10 3. MAIN PCB ASSY .11 4. POWER TRANSFORMER .11 ADJUSTMENT .12 TROUBLE SHOOTING .13 1. The power can not be turned on. (Power indication LED does not light.） .13 2. The power tur

4、ned on, but a sound does not output normally. (Both channels) .13 BLOCK AND LEVEL DIAGRAM .15 WIRING DIAGRAM .16 PRINTED WIRING BOARDS .17 MAIN .17 FRONT .19 HEADPHONE .19 POWER (PMA-720AE) .20 POWER (PMA-520AE) .20 REMOTE CONTROL .21 FUNCTION .21 POWER SW .21 VOLUME .21 SCHEMATIC DIAGRAMS (1/2) .22

5、 TONE PART .22 POWER PART .22 FUNCTION SW PART .22 VOLUME PART .22 POWER SW PART .22 FLASHER INOUT PART .22 MAIN PART .23 EXPLODED VIEW (PMA-720AE) .24 PARTS LIST OF EXPLODED VIEW (PMA-720AE) .25 PACKING VIEW (PMA-720AE) .26 PARTS LIST OF PACKING & ACCESSORIES (PMA-720AE) 26 EXPLODED VIEW (PMA-520AE

6、) .27 PARTS LIST OF EXPLODED VIEW (PMA-520AE) .28 PACKING VIEW (PMA-520AE) .29 PARTS LIST OF PACKING & ACCESSORIES (PMA-520AE) 29 SEMICONDUCTORS .31 1. ICs .31 PARTS LIST OF P.C.B. UNIT .35 FRONT PCB ASSY (PMA-720AE) .35 FRONT PCB ASSY (PMA-520AE) .38 MAIN PCB ASSY (PMA-720AE) .40 MAIN PCB ASSY (PMA

7、-520AE) .46 RadioFans.CN 收音机爱 好者资料库 3 ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref. No. in schematic diagrams, pri

8、nted wiring board diagrams, block diagrams, and parts lists. 1.Press Ctrl+Shift+F on the keyboard. The Search window appears. Ctrl Shift F 2.Enter the Ref. No. you want to search for in the Search window, and then click the Search button. A list of search results appears. 3.Click an item on the list

9、. The screen jumps to the page for that item, and the search phrase is displayed. 4 Using Adobe Reader (Windows version) Properties Click this button and check that the printer is set to a suitable paper size. Page to print Select the following checkbox. More Options : Current View Page Sizing & Han

10、dling Select the following checkbox. Size / Size Options : Fit Add notes to this data (Sign) The Sign function lets you add notes to the data in this manual. Save the file once you have finished adding notes. Example using Adobe Reader X On the View menu, click Sign. The Sign pane appears. Example u

11、sing Adobe Reader 9 On the Document menu, click Sign. Magnify schematic / printed wiring board diagrams - 1 (Ctrl+Space, mouse operation) Press Ctrl+Space on the keyboard and drag the mouse to select the area you want to view. The selected area is magnified. CtrlSpace 0 When you want to move the are

12、a shown, hold down Space and drag the mouse. When you want to show a full page view, press Ctrl+0 on the keyboard. Print a magnified part of the manual The Properties dialog box and functions will vary depending on your printer. 1. Drag the mouse to magnify the part you want to print. 2. On the File

13、 menu, click Print. 3. Configure the following settings in the Print dialog box. 4. Click the Print button to start printing. 5 Magnify schematic / printed wiring board diagrams - 2 (Pan & Zoom function) The Pan & Zoom function lets you see which part of a magnified diagram is being shown in a separ

14、ate window. Example using Adobe Reader X On the View menu, point to Zoom, and then click Pan & Zoom. The Pan & Zoom window appears on the screen. Example using Adobe Reader 9 On the Tools menu, point to Select & Zoom, and then click Pan & Zoom Window. Magnify schematic / printed wiring board diagram

15、s - 3 (Loupe Tool function) The Loupe Tool function lets you magnify a specific part of a diagram in a separate window. Example using Adobe Reader X On the View menu, point to Zoom, and then click Loupe Tool. The Loupe Tool window appears on the screen. Example using Adobe Reader 9 On the Tools menu

16、, point to Select & Zoom, and then click Loupe Tool Window. 6 SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage curren

17、t check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. Be sure to test for leakage current with the AC plug in both polarities, in addition, when

18、 the sets power is in each state (on, off and standby mode), if applicable. CAUTION Please heed the following cautions and instructions during servicing and inspection. Heed the cautions! Cautions which are delicate in particular for servicing are labeled on the cabinets, the parts and the chassis,

19、etc. Be sure to heed these cautions and the cautions described in the handling instructions. Cautions concerning electric shock! (1) An AC voltage is impressed on this set, so if you touch internal metal parts when the set is energized, you may get an electric shock. Avoid getting an electric shock,

20、 by using an isolating transformer and wearing gloves when servicing while the set is energized, or by unplugging the power cord when replacing parts, for example. (2) There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly!

21、Through great care is taken when parts were manufactured from sheet metal, there may be burrs on the edges of parts. The burrs could cause injury if fingers are moved across them in some rare cases. Wear gloves to protect your hands. Use only designated parts! The sets parts have specific safety pro

22、perties (fire resistance, voltage resistance, etc.). Be sure to use parts which have the same properties for replacement. The burrs have the same properties. In particular, for the important safety parts that are indicated by the z mark on schematic diagrams and parts lists, be sure to use the desig

23、nated parts. Be sure to mount parts and arrange the wires as they were originally placed! For safety seasons, some parts use tapes, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires by a

24、rranging them and using clamps to keep them away from heating and high voltage parts, so be sure to set everything back as it was originally placed. Make a safety check after servicing! Check that all screws, parts and wires removed or disconnected when servicing have been put back in their original

25、 positions, check that no serviced parts have deteriorate the area around. Then make an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, di

26、sconnect the antenna, plugs, etc., and on the power. Using a 500V insulation resistance tester, check that the insulation resistance value between the inplug and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is 1M or greater. If it is less, the set

27、must be inspected and repaired. Many of the electric and the structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and the use of replacement parts with higher ratings (rated power and withstand voltage) does not necess

28、arily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and the parts list in this service manual. Be sure to replace them with the parts which have the designated part number. (1) Schematic diagrams .Indicated by th

29、e z mark. (2) Parts lists .Indicated by the z mark. The use of parts other than the designated parts could cause electric shocks, fires or other dangerous situations. CAUTION Concerning important safety parts 7 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical character

30、istics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to

31、 either side of the power cord is less than 460 kohms, the set is defective. WARNING: DO NOT return the set to the customer unless the problem is identified and remedied. NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS O

32、THERWISE INDICATED. P INDICATES MICRO-MICRO FARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts indicated by nsp on this table cannot be supplied. When ordering a part, make a clear distinction between 1 and I

33、 (i) to avoid mis-supplying. A part ordered without specifying its part number can not be supplied. General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) Parts indicated by the z mark have critical chara

34、cteristics. Use ONLY replacement parts recommended by the manufacturer. General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) Part indicated by mark is not illustrated in the exploded view. WARNING: 1. 2. 3. 4. 5. 6. NOTE FOR PARTS LIST 8

35、 TECHNICAL SPECIFICATIONS nPMA-720AE n Power amplifier section Rated output power : 2-channel driving (CD SP OUT) 50 W + 50 W (8 , 20 Hz 20 kHz, T.H.D. 0.07 %) Dynamic power : 85 W + 85 W (4 , DIN, 1 kHz, T.H.D. 0.7 %) Total harmonic distortion : 0.01 % (Rated output: 3 dB), 8 , 1 kHz Output termina

36、ls : Speaker A or B: 4 16 A + B: 8 16 Suited for headphones/stereo headphones n Pre amplifier section Equalizer amplifier output (REC OUT terminals) : 150 mV Input sensitivity/Input impedance : PHONO (MM): 2.5 mV/47 k CD, TUNER, AUX, Network, RECORDER: 120 mV / 30 k (SOURCE DIRECT OFF) 120 mV / 16 k

37、 (SOURCE DIRECT ON) RIAA deviation : PHONO (MM): 20 Hz 20 kHz0.5 dB n Overall performance S/N (IHFA weight) : PHONO (MM): 86 dB (With input terminals short-circuited, 5 mV input signal) CD, TUNER, AUX, Network, RECORDER: 107 dB (input terminals short-circuited) Tone control : BASS: 100 Hz8 dB TREBLE

38、: 10 kHz8 dB Loudness: 100 Hz: +6 dB, 10 kHz: +6 dB n General Power supply : AC 230 V, 50/60 Hz Power consumption : 200 W Power consumption in standby mode : 0.3 W Power outlets : 3 switched outlets, total capacity 100 W (0.43 A) nPMA-520AE n Power amplifier section Rated output power : 2-channel dr

39、iving (CD SP OUT) 45 W + 45 W (8 , 20 Hz 20 kHz, T.H.D. 0.07 %) Dynamic power : 70 W + 70 W (4 , DIN, 1 kHz, T.H.D. 0.7 %) Total harmonic distortion : 0.02 % (Rated output: 3 dB), 8 , 1 kHz Output terminals : Speaker: 4 16 Suited for headphones/stereo headphones n Pre amplifier section Equalizer amp

40、lifier output (REC OUT terminals) : 150 mV Input sensitivity/Input impedance : PHONO (MM): 2.5 mV/47 k CD, TUNER, AUX, Network, RECORDER: 120 mV / 30 k (SOURCE DIRECT OFF) 120 mV / 16 k (SOURCE DIRECT ON) RIAA deviation : PHONO (MM): 20 Hz 20 kHz0.5 dB n Overall performance S/N (IHFA weight) : PHONO (MM): 84 dB (With input terminals short-circuited, 5 mV input signal) CD, TUNER, AUX, Network, RECORDER: 105 dB (input terminals short-circuited) Tone control : BASS: