Denon-RCDM35DAB-rec-sm维修电路原理图.pdf

《Denon-RCDM35DAB-rec-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-RCDM35DAB-rec-sm维修电路原理图.pdf（54页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL STEREO CD RECEIVER MODELRCD-M35DAB RCD-M33 TOKYO, JAPAN Denon Brand Company, D&M Holdings Inc. X0230V.06 DE/CDM 0701 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions

2、without fail. For purposes of improvement, specifications and design are subject to change without notice. 本文中使用、説明都合上現物 多少異場合。 修理際、必取扱説明書参照上、作業行 。 前、 必読。本機、火災、感電、 対安全性確保、配慮 、法的電気用品安全法 、所定許可得製造。 従際、安全性維 持、記載 注意事項必守。 本機仕様性能改良、予告変更 。 補修用性能部品保有期間、製造打切後8年。 注意 For U.S.A., Canada, Europe, U.K. & Japan mod

3、el Ver. 6 Please refer to the MODIFICATION NOTICE. RadioFans.CN 收音机爱 好者资料库 2 RCD-M35DAB/M33 Please heed the points listed below during servicing and inspection. Heed the cautions! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated

4、on labels or seals. Be sure to heed these cautions and the cau- tions indicated in the handling instructions. Caution concerning electric shock! (1) An AC voltage is impressed on this set, so touching inter- nal metal parts when the set is energized could cause electric shock. Take care to avoid ele

5、ctric shock, by for ex- ample using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembl

6、y! Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. Only use designated parts! The sets parts have specific safety properties

7、(fire resis- tance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In particu- lar, for the important safety parts that are marked ! on wiring diagrams and parts lists, be sure to use the designated parts. Be sure to mount parts and arrange the

8、 wires as they were originally! For safety reasons, some parts use tape, tubes or other insu- lating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating an

9、d high voltage parts, so be sure to set everything back as it was originally. Inspect for safety after servicing! Check that all screws, parts and wires removed or discon- nected for servicing have been put back in their original posi- tions, inspect that no parts around the area that has been servi

10、ced have been negatively affected, conduct an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and tur

11、n the power switch on. Using a 500V insulation resistance tester, check that the insulation re- sistance between the terminals of the power plug and the ex- ternally exposed metal parts (antenna terminal, headphones terminal, microphone terminal, input terminal, etc.) is 1M or greater. If it is less

12、, the set must be inspected and repaired. Concerning important safety parts Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and

13、 withstand voltage) does not necessarily guarantee that safety performance will be pre- served. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designat- ed part number. (1) Schematic

14、 diagrams . Indicated by the ! mark. (2) Parts lists . Indicated by the ! mark. Using parts other than the designated parts could result in electric shock, fires or other dangerous situations. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and

15、 service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is l

16、ess than 460 kohms, the unit is defective. LASER RADIATION Do not stare into beam or view directly with optical instruments, class 3A laser product. CAUTION CAUTION 、点検時注意願。 注意事項守！ 特注意必要個所 、部品、捺印注意事項 表示。 注意書取扱説明書 注意事項必守。 感電注意！ (1) 、交流電圧印加通電時 内部金属部触感電。従 通電時、絶縁使用手袋着 用、部品交換、電源抜感電 注意。 (2) 内部高電圧部分、通電時取扱

17、十分注意。 分解、組立作業時注意！ 板金部品端面、部品製造時充分管理 、 板金端面鋭利箇所有 、 部品端面触指動怪我場 合十分注意作業下。 手保護 手袋着用。 指定部品使用！ 部品難燃性耐電圧安全上特性持 。従交換部品、使用 同特性部品使用。特配線図、部品 表 ! 印指定安全上重要部品必指定 使用。 部品取付配線引、 元！ 安全上、絶縁材料使用、 基板浮取付部品。 内部 配線引発熱部品高圧部 品接近配慮、 必 元。 後安全点検！ 取外、部品、配線元 、 個所周辺劣化 点検、外部金属端子部 、電源刃間絶縁、安 全性確保確認。 （絶縁方法） 電源電源抜、 外、電源入。500V 絶縁抵抗計用 、電源

18、端子外部露出金属部 端子、端子、端子、入力端子 間、絶縁抵抗値 M 以上確認 。値以下点検修理必要。 安全上重要部品 本機使用多電気部品、 機構部品安全 上、 特別特性持。 特性場合、 外観判別、部品高定格（定 格電力、耐圧）持使用安全性維持 、限。安全上特性持部品、 配線図、 部品表表示 必指定部品番号使用願 。 (1) 配線図 ! 表示。 (2) 部品表 ! 表示。 指定部品異使用場合 、感電、火災危険生恐 。 注意 注意 RadioFans.CN 收音机爱 好者资料库 3 RCD-M35DAB/M33 CAUTION IN SERVICING Initializing RCD-M35DA

19、B/M33 RCD-M35DAB/M33 initialization should be performed when the com, and peripheral parts of com are replaced. 1. Switch off the unit and remove the AC cord from the wall out- let. 2. Hold the following button and MENU/SET button, and plug the AC cord into the outlet. Note: All user settings will b

20、e lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization. BLOCK DIAGRAM 時注意事項 本機初期化 周辺部品交換場合、本機初期化 行下。 1.電源押状態、壁電源 電源抜。 2. MENU/SET 同時押、 電源差込。 初期化。 注意 : 初期化行客様設定内容工場出荷状 態戻、設定内容控 初期化後再設定。 2 3 4 RCD-M3

21、5DAB/M33 LEVEL DIAGRAM 5 RCD-M35DAB/M33 CD TEST MODE NoKey nameFunctionDisplay 1 Version No. of Main MPU Dis- play Mode S1 Plug AC cord into power outlet while pressing ON/STANDBY Key and SDB/TONE Key same time on Main Unit. The Version number of Main MPU is displayed. Unplug AC cord to clear this m

22、ode. Upper : _ _ _ _ Ver _ * * * * _ _ _ _ * is the Version number of Main MPU Lower : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 FLD(VFD) check- ing mode S2 Plug AC cord into power outlet while pressing ON/STANDBY Key and OPEN/CLOSE Key same time on Main Unit. All segment of FLD is turning on and off every

23、one second. Unplug AC cord to clear this mode. All segment turn on and off. 3 EEPROM testing Mode S3 Plug AC cord into power outlet while pressing ON/STANDBY Key and STOP/BAND Key same time on Main Unit. POWER LED illuminant Orange to sign the test mode started. When power LED lighted GREEN, this EE

24、PROM test was OK. When power LED lighted RED, this EEPROM test was NG. Unplug AC cord to clear this mode. 4 DAB Function CHECK Mode. (This test for only RCD- M35DABSREK) Plug AC cord into power outlet while pressing MENE/SET Key and Key same time on Main Unit. Turn the power on then set the volume l

25、evel to 25 (-18dB). Set the function to TUNER, the band to DAB. Enable service reception without conducting DAB auto scanning. (After about 10 to 15 seconds) (Without auto scanning) Receive frequency 12C : 227.360MHz (Without switching the DISPLAY key) Signal quality display Unplug AC cord to clear

26、this mode. 5CD service mode Plug AC cord into power outlet while pressing ON/STANDBY Key and FUNCTION Key same time on Main Unit. Move the slide to the initially set position (10 mm towards the outside from the innermost position). Check by performing key input. Refer to 5.1 to 5.6. Cancel the mode

27、by turning the power back on. Input of keys other than those used in this mode is not guaranteed. (OK if malfunction occurs) flashing Upper : _ 00 _ CD_Ver _ * * * * _ displayed * : CD microprocessor version no. Lower : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5.1Disc loading Press the CD OPEN/CLOSE key to o

28、pen the tray. Set a disc on the tray, then press the CD OPEN/ CLOSE key again to close the tray. The disc is mounted automatically. Move the slide to the initially set position (10 mm towards the outside from the innermost position) and stop in this status. Continue S6 display CD No名称機能表記 1 表示 S1 本体

29、 ON/STANDBY SDB/TONE 同時 押、AC 接続 . Ver 表示MUTING ON AC 抜解除 上段：_ _ _ _ Ver _ * * * * _ _ _ _ 表示 *： Ver 番号 下段：_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 FL(VFD) 管 S2 本体 ON/STANDBY CD OPEN/CLOSE 同時押、AC 接続 FL 管全 2 秒周期点滅 (1 秒点灯、1 秒 消灯 ) MUTING ON AC 抜解除 全点灯消灯 3 EEPROM TEST S3 本体 ON/STANDBY CD STOP/BAND 同 時押、AC 接続 P

30、OWER LED 橙色点灯 (TEST 開始 ) MUTING ON EEPROM TEST 後、OK 時、緑色点灯 EEPROM TEST 後、NG 時、赤色点灯 AC 抜解除 4 DAB CHECK (only RCD- M35DABSREK） 本体 MENU/SET 同時押 、AC 接続 POWER ON 後、VOL LEVEL 25(-18dB) . Function TUNER、 BAND DAB 。 DAB AUTO SCAN 行受信 可能 （約 10 15 秒後） （AUTO SCAN ）周波数 12C： 227.360MHz 受信 （DISPLAY 切替）Signal Qual

31、ity 表 示 AC 抜 解除 5CD 本体 ON/STANDBY FUNCTION 同時 押、AC 接続 初期設定位置移動 （最内周 外側 10mm 位置） 入力行5.1 5.6 参照 電源再投入解除 使用以外入力保証 （異常動作） 点滅 上段：_ 00 _ CD_Ver _ * * * * _ 表示 *：CD Ver 番号 下段：_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5.1装着 CD OPEN/CLOSE 開 置、再度 CD OPEN/CLOSE 閉 初期設定位置（最内周外側 10mm 位置）移動、状態 S6 表示継続 6 RCD-M35DAB/M33 5.2Se

32、rvo check Press the CD PLAY/PAUSE key. Execute the following steps. LD ON (with servo still stopped) FOCUS ON (disc rotation, tracking off) If no disc loaded, retry then stop. CLV ON TRACKING ON SUB CODE readout (playback sound output) When display is as in and the PLAY button is pressed, conduct BE

33、R (Block Error Rate) display for 2 seconds. (Display total no. generated in 10 seconds.) Press PLAY button continuously for over 1 second to switch directly to SUB CODE readout in step . flashing Upper : 01 _ _ _ _ _ LD_ON _ displayed Lower : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Upper : _ 02 _ _ _ _ Focu

34、s_ON _ displayed Upper : _ 03 _ _ _ _ _ _ CLV_ON _ displayed Upper : _ 04 _ Tracking_ON _ displayed Upper : _ 05 _ _ _ Tr _ _ XX:XX displayed : T.No XX:XX : Time Upper : _ _ _ _ _ _ ERR _ # displayed # : B.E.R. 5.3Pickup movement In the stop mode, pickup moves in REV (inwards) or FWD (outwards) dire

35、ction when key or key pressed. When key pressed, move to stop operation after detection that inner switch has turned on. Pickup movement stops when key released. (Pickup moves while key is pressed.) Continuous display of previous time 5.4Stop When STOP key is pressed, play operation and servo stop.

36、After stopping, conduct reading of auto adjust values. Same as 5. 5.5All servo on When MENU/SET key is pressed, all servos turn on, auto adjustment is performed and switch to playback operation. (Playback sound output) flashing Upper : _ _ _ _ _ _ Tr _ _ XX:XX displayed : T.No XX:XX : Time Lower : _

37、 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ NoKey nameFunctionDisplay 5.2 CD PLAY/PAUSE 押下記実行 LD ON( 停止 ) FOCUS ON( 回転、 OFF) 無場合、後停止 CLV ON TRACKING ON SUB CODE 読出（再生音出力） 表示時 PLAY 押、2 秒間 BER(Block Error Rate) 表示行 (10 秒間間発生総数表示） PLAY 1 秒以上押続、 SUB CODE 読出移行 点滅 上段： 01 _ _ _ _ _ LD_ON _ 表示 下段：_ _ _ _ _ _ _ _ _ _ _ _

38、 _ _ _ _ 上段： _ 02 _ _ _ _ Focus_ON _ 表示 上段：_ 03 _ _ _ _ _ _ CLV_ON _ 表示 上段：_ 04 _ Tracking_ON _ 表示 上段：_ 05 _ _ _ Tr _ _ XX:XX 表示 ：T.No XX:XX：時間 上段：_ _ _ _ _ _ ERR _ # 表示 #：B.E.R. 5.3移動 状態押 、 REV( 内周側 ) FWD( 外 周側 ) 方向移動 押時、内周 SW ON 検 出後動作移行 離移動停止( 押間、移動) 前回表示継続 5.4停止 STOP 押、PLAY 動作及停止 停止後、自動調整値読込行 5

39、同 5.5全 ON MENU/SET 押全 ON 、自動 調整行再生動作移行 （再生音 出力） 点滅 上段：_ _ _ _ _ _ Tr _ _ XX:XX 表示 ：T.No XX:XX：時間 下段：_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ No名称機能表記 7 RCD-M35DAB/M33 5.6 Adjustment value display When SDB/TONE key is pressed, the adjustment values are displayed in the following order. FOCUS BALANCE FOCUS GAI

40、N TRACKING BALANCE TRACKING GAIN FOCUS OFFSET TRACKING OFFSET RFRP Return to . (NOTE) If auto adjustment is not completed, proper values are not displayed. flashing Upper : FOCUS _ BALANCE _ _ _ Lower : XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX : Adjustment value Upper : FOCUS _ GAIN _ _ _ _ _ _ Lower : XX

41、_ _ _ _ _ _ _ _ _ _ _ _ _ _ XX : Adjustment value Upper : TRACKING _ BALANCE Lower : XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX : Adjustment value Upper : TRACKING _ GAIN _ _ _ Lower : XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX : Adjustment value Upper : FOCUS _ OFFSET _ _ _ _ Lower : XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ X

42、X : Adjustment value Upper : TRACKING _ OFFSET _ Lower : XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX : Adjustment value Upper : RFRP _ _ _ _ _ _ _ _ _ _ _ _ Lower : XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX : Adjustment value NoKey nameFunctionDisplay 5.6調整値表示 SDB/TONE 押、下記順番調整値 表示 FOCUS BALANCE FOCUS GAIN TRACKING B

43、ALANCE TRACKING GAIN FOCUS OFFSET TRACKING OFFSET RFRP 戻。 ( 注 ) 自動調整終了無場合正常値 表示 点滅 上段：FOCUS _ BALANCE _ _ _ 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 上段：FOCUS _ GAIN _ _ _ _ _ _ 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 上段：TRACKING _ BALANCE 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 上段：TRACKING _ GAIN

44、_ _ _ 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 上段：FOCUS _ OFFSET _ _ _ _ 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 上段：TRACKING _ OFFSET _ 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 上段：RFRP _ _ _ _ _ _ _ _ _ _ _ _ 下段：XX _ _ _ _ _ _ _ _ _ _ _ _ _ _ XX：調整値 No名称機能表記 8 RCD-M35DAB/M33 6CD heat run mode Plug

45、AC cord into power outlet while pressing ON/STANDBY Key and MENU/SET Key same time on Main Unit.(Be sure to insert the CD before this operation) Switches to mode according to key input. See 6.1 and 6.2. If an error occurs, display the error and stop operation at that point. Number of operations held

46、. See 6.3 to 6.5. Heat run no. cleared when STOP key pressed. Mode canceled and tray opened after CD OPEN/ CLOSE key pressed. Unplug AC cord to clear this mode too. lit Normal display except when lit. 6.1 Normal heat run mode After CD heat run mode has started, press the CD PLAY/PAUSE key.(Be sure t

47、o finish reading the TOC before push CD PLAY/PAUSE key) Count this as the 0th heat run repetition. Play from the first to last track on disc. If disc being used has less than 20 tracks, play all tracks. If disc has 21 or more tracks, skip to final track after playback of first track has finished. Af

48、ter disc playback has finished, move pickup to innermost position and open tray. When loader open status detected, close tray again, re-read TOC and start playback from the first track on the disc. The heat run repetition no. is incremented (increased by 1) when the tray is opened. Conduct to repeat

49、edly. lit , In cases other than when is lit, same display as during normal playback. Upper : _ CD _ _ _ _ _ _ _ _ XXXX_ Lower : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ XXXX : No. of heat run repetitions Upper : _ CD _ _ _ 01Tr _ _ _ _ : _ _ Lower : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6.2 Automatic mounting mode After CD heat run mode has started, press the CD STOP/BAND key once in the stop mode.(Be sure to finish