HarmanKardon-AVR360.230-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR360.230-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR360.230-avr-sm维修电路原理图.pdf（138页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon Service Manual AVR 360/230 7 x 50W 7.1 CHANNEL A/V RECEIVER CONTENTS EXPLODED VIEW AND PARTS 12 ELECTRICAL PARTS LIST 13 SEMICONDUCTOR PINOUTS 46 PCB DRAWINGS 116 BLOCK DIAGRAM 123 WIRING DIAGRAM 124 AMP BIAS ADJUSTMENT 125 SCHEMATIC DIAGRAMS 126-138 ESD WARNING 2 FRONT AND REAR PANEL

2、S 3 REMOTE CONTROLS 5 TROUBLESHOOTING GUIDE 8 PROCESSOR RESET 8 BASIC SPECIFICATIONS 9 PACKAGE LISTS AND PARTS 10 DISASSEMBLY 11 Released EU2010 Harman Consumer Group, Inc. Rev 0, 03/2010 8500 Balboa Boulevard Northridge, California 91329 harman/kardonAVR 360/230 Service Manual Page 1 of 138 RadioFa

3、ns.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resista

4、nce, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) device

5、s can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help red

6、uce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available

7、 discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge bu

8、ild-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use f

9、reon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted togethe

10、r by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is appl

11、ied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static e

12、lectricity sufficient to damage an ES devices. CAUTION : harman/kardonAVR 360/230 Service Manual Page 2 of 138 RadioFans.CN 收音机爱 好者资料库 7 460 Set up MIC ENGLISH FRONT-PANEL CONTROLS Power indicator Standby/On Switch Info Settings OK USB PortDigital Audio Inputs (Optical and Coaxial Front) Headphone J

13、ack/ EzSet/EQ Microphone Input Back/ExitAudio Effects Surround ModesAnalog Audio Front Inputs KL Navigation M N Navigation Remote IR SensorSetupMessage DisplayVolume Power Indicator: This LED has three possible modes: Main Power Off : When the AVR is unplugged or the Main Power Switch is off, this L

14、ED is off. Standby : Amber indicates that the AVR is ready to be turned on. On : When the AVR is turned on, this LED turns white. NOTE: If the PROTECT message ever appears, turn off the AVR and unplug it. Check all speaker wires for a possible short. If none is found, bring the unit to an authorized

15、 Harman Kardon service center for inspection and repair before using it again. Standby/On Switch: This electrical switch turns the receiver on, or places it in Standby mode for quick turn-on. AVR Settings Button: Press this button to access the AVRs main menu. Info Settings Button: Press this button

16、 to directly access the AVRs Source Info submenu, which contains the settings for the current source. Resolution: Press this button to access the AVRs video output resolution setting: 576i, 576p, 720p, 1080i or 1080p. IMPORTANT NOTE: If the AVRs video output resolution is set higher than the capabil

17、ities of the actual connection, you will not see a picture. If the best available video connection from the AVR to the TV is composite press this button and change the resolution to 576i. Audio Effects: Press this button to directly access the Audio Effects submenu, which allows adjustment of the to

18、ne and other audio controls. See the Initial Setup section for more information. Video Modes: Press this button for direct access to the Video Modes submenu, which contains settings that may be used to improve the picture, if necessary, after you have adjusted the picture settings using the video di

19、splay or TV. Surround Modes: Press this button to select a surround sound (e.g., multichannel) mode. The Surround Modes menu will appear on screen, and the menu line will appear in the front-panel display. See the Advanced Functions Manual for more information on surround modes. Source List: Press t

20、his button to select a source device, which is a component where a playback signal originates, e.g., DVD. Back/Exit: Press this button to return to the previous menu, or to exit the menu system. ResolutionVideo ModesVideo Front Input harman/kardon AVR 360/230 Service Manual Page 3 of 138 RadioFans.C

21、N 收音机爱 好者资料库 9 ENGLISH Coaxial Digital Audio Output Subwoofer Output Analog 1-5 Inputs Fan Vents Optical 1-3 Digital Audio Inputs (AVR 360: Optical 1-2) Analog 2 use an analog video connection instead. Always make a separate audio connection. Analog 1 5 Inputs: Connect the left and right analog audi

22、o outputs of a source device to any of these inputs. These inputs may be paired with any video inputs. NOTES: The Analog 2 and 4 inputs are each associated with a set of outputs. Consider using these connectors for an audio or video recorder. You may optionally connect a source to both an analog and

23、 digital audio input. This is useful for making recordings, for multizone applications or simply as a backup. Main Power Switch 6-/8-Channel Inputs Remote IR Output Coaxial 1-2 Digital Audio Inputs Preamp Outputs (AVR 460 only) Surround Back/Zone 2 Speaker Outputs FM Antenna AM Antenna Zone 2 Audio

24、OutputsSurround Speaker Outputs Front Speaker Outputs A-BUS Port A-BUS on AVR 460 only A-BUS Power Input HDMI 1-4 Inputs HDMI Monitor Output Remote IR Input Carrier IR Output (AVR 460 only) Video Monitor Output Switched AC Accessory Outlet Center Speaker Outputs A-BUS IR Output (AVR 460 only) Video

25、1-3 Inputs harman/kardon AVR 360/230 Service Manual Page 4 of 138 RadioFans.CN 收音机爱 好者资料库 1011 Info Back/ExitMenu OFF ZR60 LEARN SETUPINFOSLEEP ENGLISH REMOTE CONTROL FUNCTIONS IR Transmitter Mute Source Selectors Transport Controls Zone Indicator Menu KLM N Navigation OK Sleep Settings AVR Settings

26、 IR Transmitter Lens AVR Power Off AVR Power On Device Power On Device Power Off Video Modes Surround Modes Activity Menu KLM N Navigation OK Disc Menu Channel Transport Controls Sleep Settings Power Off Back/Exit Volume Controls Zone Selector Source Selectors Audio Effects Alphanumeric Keys Last Ba

27、ck/Exit Light Soft Keys Volume Mute Record Info Settings Setup Zone Selector The AVR 460/AVR 360 remote is capable of controlling 8 devices, including the AVR itself and an iPod docked in The Bridge III. During the installation process, you may program the codes for your source components into the r

28、emote. To operate a component, press its Selector button to change the device mode. Each Source Selector has been preprogrammed to control certain types of components, with only the codes specific to each brand and model changing, depending on which product code is programmed. The AUX and Cable/ SAT

29、 Source Selectors may be used for multiple device types. Other Source Selectors may be reassigned to other device types (see Initial Setup section). AUX Source Selector: CD player, VCR, HDTV set-top box, PVD or TiVo set-top box. Refer to page 23 for details on Source Selection. Cable/SAT Source Sele

30、ctor: Cable set-top box or satellite set-top box. IMPORTANT NOTE: All of the AVR 460/AVR 360s audio and video inputs are independently assignable. Select the inputs to which the device is physically connected during Initial Setup. Any device may be connected to any compatible input and given any nam

31、e (e.g., DVD or Game). Most of the buttons on the remote have dedicated functions, although the precise codes transmitted vary, depending on the device mode. Due to the wide variety of functions for various source devices, only a few of the most- often used functions on the remote have been included

32、: alphanumeric keys, transport controls, television-channel control, menu access, and power on and off. MAIN REMOTE CONTROLZONE 2 REMOTE CONTROL (AVR 460 only) Learn (AVR 460 only) Not used AVR 0153CSK - HK AVR460-360 OM EURO, WORK09os.indd 1106/08/09 13:13:46 harman/kardon AVR 360/230 Service Manua

33、l Page 5 of 138 RadioFans.CN 收音机爱 好者资料库 1213 REMOTE CONTROL FUNCTIONS Buttons dedicated to the AVR are available at any time, even in another device mode: AVR Power On and Off, Audio Effects, Video Modes, Surround Modes, Volume, Mute and Sleep Settings. Press the AVR Settings Button near the bottom

34、of the remote to return it to AVR mode. A buttons function depends on which component is being controlled. See Table in the Advanced Functions Manual for listings of the functions for each type of component. IR Transmitter Lens: As buttons are pressed on the remote, infrared codes are emitted throug

35、h this lens. AVR Power On Button: Press to turn on the AVR. The Master Power Switch on the rear panel must be on. AVR Power Off Button: Press to turn off the AVR. Device Power On Button: Press a devices Source Selector, then press this button to turn on the device. Device Power Off Button: Press a d

36、evices Source Selector, then press this button to turn off the device. Source Selectors: Press one of these buttons to select a source device, e.g., Blu-ray Player, CS, Cable TV, DVD or satellite tuner. This will also turn on the receiver and switch the remotes device mode to operate the source. The

37、 first press of the Radio Selector switches the AVR to the last-used tuner band (AM or FM). Each successive press changes the band. Audio Effects: Press to directly access the Audio Effects submenu, which allows adjustment of the AVRs tone and other audio controls. See the Initial Setup section for

38、more information. Video Modes: Press for direct access to the Video Modes submenu, which contains picture settings to be used after you have adjusted the picture settings on the video display or TV. See the Advanced Functions Manual for more information. Surround Modes: Press to directly access the

39、Surround Modes submenu. Select a Surround Mode category: Auto Select, Virtual Surround, Stereo, Movie, Music or Video Game. The surround mode will change when the menu line is highlighted. To change the surround mode for the selected category, press the OK Button when the menu line is highlighted, a

40、nd select one of the available surround mode options using the KL Buttons. Press the OK Button, or press the Back/Exit Button to exit the Surround Modes menu and display the next higher menu in the hierarchy. See the Advanced Functions Manual for more information on surround modes. Alphanumeric Keys

41、: Use these buttons to enter numbers for radio station frequencies or channels, or to select station presets. Last Channel: When controlling a cable, satellite or HDTV set-top box or a TV, press this button to return to the previous station or channel. Activity: With this button, up to 11 Activities

42、 may be programmed to transmit a series of commands with a single press. Execute an Activity by pressing this button, then the Alphanumeric Key (or the AVR Power On or Off Button by themselves) into which it was programmed. See the Advanced Functions Manual for more information on Activities. Back/E

43、xit: Press to return to the previous menu or to exit the menu system. Menu Button: This button is used within the Now Playing menu for the tuner, The Bridge III and to display the main menu on some source devices. To display the AVRs main menu, press the Setup Button. Navigation (KLM N) and OK Butto

44、ns: These buttons are used to make selections within the menu system and to operate the tuner. Light: Press to illuminate the buttons on the remote. Press it again to turn the back light off, or wait 10 seconds after the last button press for the light to turn off on its own. Disc Menu: While a DVD

45、is playing, press the DVD Source Selector, then this button, to display the discs menu. Soft Keys: These buttons are used with some source devices. See Table A14 in the Advanced Functions Manual for details. They are also used with a Teletext-capable television if your broadcast, cable or satellite

46、provider offers Teletext service. Volume Control: Press to raise or lower the volume. 0153CSK - HK AVR460-360 OM EURO, WORK09os.indd 1206/08/09 13:13:47 harman/kardon AVR 360/230 Service Manual Page 6 of 138 RadioFans.CN 收音机爱 好者资料库 1213 ENGLISH REMOTE CONTROL FUNCTIONS Mute Button: Press to mute the

47、 AVRs speaker and headphone outputs. To end the muting, press this button, adjust the volume, or turn off the receiver. Channel/Page Control: When the tuner has been selected, this control changes a preset radio station. While operating a cable, satellite or HDTV set- top box or a television, press

48、these buttons to change channels. Transport Controls: These buttons are used to control source playback and The Bridge III. Record Button: Use this button to make recordings when an audio or video recorder is in use. Setup Button: Press to display the AVRs Main Menu, or to switch the remote to AVR d

49、evice mode. Info Settings Button: Press to display the AVRs Info Menu, which contains the settings for the current source. Sleep Settings Button: Press to activate the sleep timer, which turns off the receiver after a programmed period of time of up to 90 minutes. Each press decreases the timer by 10 minutes, ending with the “Sleep Off” message. Zone Selector: Use this switch to select whether AVR commands will af