Hitachi-DVP415U-cd-sm维修电路原理图.pdf

《Hitachi-DVP415U-cd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Hitachi-DVP415U-cd-sm维修电路原理图.pdf（50页珍藏版）》请在收音机爱好者资料库上搜索。

1、TK No.9103E SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT DVD PLAYER SERVICE MANUAL 2001MarchDigital Media Products Division, Tokai DV-P415U 1. Precautions 2. Product Specifications 3. Operating Instructions 4. Disassembly and Reassembly 5. Troubleshooting 6. Exploded Views 7. Repla

2、cement Parts List 8. Block Diagrams 9. PCB Diagrams 10. Wiring Diagram 11. Schematic Diagram CONTENTS RadioFans.CN 收音机爱 好者资料库 1-1 1. Precautions 1-1 Safety Precautions 1) Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited t

3、o, the following items: (1) Be sure that no built-in protective devices are defective or have been defeated during servicing. (1)Protective shields are provided to protect both the technician and the customer. Correctly replace all missing protective shields, including any remove for servicing conve

4、nience. (2)When reinstalling the chassis and/or other as- sembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks

5、. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. (2) Be sure that there are no cabinet openings through which adults or children might be able to insert their fingers and contact a hazardous voltage. Such openings includ

6、e, but are not limited to, excessively wide cabinet ventilation slots, and an improperly fitted and/or incorrectly secured cabinet back cover. (3) Leakage Current Hot Check-With the instrument completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use a isolation trans

7、former during this test.) Use a leakage current tester or a metering system that complies with American National Standards institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1270 (40.7).With the instruments AC switch first in the ON position and then in the OFF

8、 position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinets, screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the

9、 chassis. Any current measured must not exceed 0.5mA. Reverse the instrument power cord plug in the outlet and repeat the test. See Fig. 1-1. Any measurements not within the limits specified herein indicate a potential shock hazard that must be eliminated before returning the instrument to the custo

10、mer. Fig. 1-1 AC Leakage Test (4) Insulation Resistance Test Cold Check-(1) Unplug the power supply cord and connect a jumper wire between the two prongs of the plug. (2) Turn on the power switch of the instrument. (3) Measure the resistance with an ohmmeter between the jumpered AC plug and all expo

11、sed metallic cabinet parts on the instrument, such as screwheads, antenna, control shafts, handle brackets, etc. When an exposed metallic part has a return path to the chassis, the reading should be between 1 and 5.2 megohm. When there is no return path to the chassis, the reading must be infinite.

12、If the reading is not within the limits specified, there is the possibility of a shock hazard, and the instrument must be re-pared and rechecked before it is returned to the customer. See Fig. 1-2. Fig. 1-2 Insulation Resistance Test DEVICE UNDER TEST (READING SHOULD NOT BE ABOVE 0.5mA) LEAKAGE CURR

13、ENT TESTER EARTH GROUND TEST ALL EXPOSED METER SURFACES ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) 2-WIRE CORD Antenna Terminal Exposed Melal Part ohm ohmmeter RadioFans.CN 收音机爱 好者资料库 Precautions 1-2 2) Read and comply with all caution and safety re- lated notes non or inside t

14、he cabinet, or on the chassis. 3) Design Alteration Warning-Do not alter of add to the mechanical or electrical design of this instrument. Design alterations and additions, including but not limited to, circuit modifications and the addition of items such as auxiliary audio output connections, might

15、 alter the safety characteristics of this instrument and create a hazard to the user. Any design alterations or additions will make you, the service, responsible for personal injury or property damage resulting therefrom. 4) Observe original lead dress. Take extra care to assure correct lead dress i

16、n the following areas: (1) near sharp edges, (2) near thermally hot parts (be sure that leads and components do not touch thermally hot parts), (3) the AC supply, (4) high voltage, and (5) antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring, Do not change spacing

17、between a component and the printed-circuit board. Check the AC power cord for damage. 5) Components, parts, and/or wiring that appear to have overheated or that are otherwise damaged should be replaced with components, parts and/ or wiring that meet original specifications. Additionally, determine

18、the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection

19、 they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by shading, an ( )or a ( )on schematics and parts lists. Use of a substitute replacement that does not have the same safety chara

20、cteristics as the recommended replacement part might created shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. Precautions 1-3 1-2 Servicing Precautions CAUTION : Before servicing Instruments covered by this service ma

21、nual and its supplements, read and follow the Safety Precautions section of this manual. Note : If unforseen circument create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions. Remember: Safety First. 1-2-1 General Servicing

22、Precautions (1) a. Always unplug the instruments AC power cord from the AC power source before (1) re-moving or reinstalling any component, circuit board, module or any other instrument assembly, (2) disconnecting any instrument electrical plug or other electrical connection, (3) connecting a test s

23、ubstitute in parallel with an electrolytic capacitor in the instrument. b. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service manual might be equipped. c. Do not apply AC power to this instrument and /or any of its electrical assemblies unless all soli

24、d-state device heat sinks are correctly in- stalled. d. Always connect a test instruments ground lead to the instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last. Note : Refer to the Safety Precautions section ground lead l

25、ast. (2) The service precautions are indicated or printed on the cabinet, chassis or components. When servicing, follow the printed or indicated service precautions and service materials. (3) The components used in the unit have a specified flame resistance and dielectric strength. When replacing co

26、mponents, use components which have the same ratings. Components i- entified by shading, by( ) or by ( ) in the circuit diagram are important for safety or for the characteristics of the unit. Always replace them with the exact replacement components. (4) An insulation tube or tape is sometimes used

27、 and some components are raised above the printed wiring board for safety. The internal wiring is sometimes clamped to prevent contact with heating components. Install such elements as they were. (5) After servicing, always check that the removed screws, components, and wiring have been in- stalled

28、correctly and that the portion around the serviced part has not been damaged and so on. Further, check the insulation between the blades of the attachment plug and accessible conductive parts. 1-2-2 Insulation Checking Procedure Disconnect the attachment plug from the AC outlet and turn the power ON

29、. Connect the insulation resi- stance meter (500V) to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive parts(see note) should be more than 1 Megohm. Note : Accessible conductive parts include metal panels, input terminal

30、s, earphone jacks, etc. Precautions 1-4 1-3 ESD Precautions Electrostatically Sensitive Devices (ESD) Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostati- cally Sensitive Devices(ESD). Examples of typical ESD devices

31、are integrated circuits and some field- effect transistors and semiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity. (1) Immediately before handling any semiconductor component or semiconductor-equipped as

32、sembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. (2) After removing an

33、electrical assembly equipped with ESD devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. (3) Use only a grounded-tip soldering iron to solder or unsolder ESD devices. (4) Use only an anti-static solder remov

34、al devices. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ESD devices. (5) Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD devices. (6) Do not remove a replacement ESD device from it

35、s protective package until immediately before your are ready to install it.(Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials). (7) Immediately before removing the protective ma- terials from the le

36、ads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION : Be sure no power is applied to the ch- assis or circuit, and observe all other safety precautions. (8) Minimize bodily motions when handling unpackaged

37、 replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ESD device). Precautions 1-5 1-4 Handling the optical pick-up The laser diode in the opt

38、ical pick up may suffer electrostatic breakdown because of potential static electricity from clothing and your body. The following method is recommended. (1) Place a conductive sheet on the work bench (The black sheet used for wrapping repair parts.) (2) Place the set on the conductive sheet so that

39、 the chassis is grounded to the sheet. (3) Place your hands on the conductive sheet(This gives them the same ground as the sheet.) (4) Remove the optical pick up block (5) Perform work on top of the conductive sheet. Be careful not to let your clothes or any other static sources to touch the unit. B

40、e sure to put on a wrist strap grounded to the sheet. Be sure to lay a conductive sheet made of copper etc.Which is grounded to the table. Fig.1-3 (6) Short the short terminal on the PCB, which is in- side the Pick-Up ASSY, before replacing the Pick- Up. (The short terminal is shorted when the Pick-

41、 Up Assy is being lifted or moved.) (7) After replacing the Pick-up, open the short terminal on the PCB. THE UNIT WRIST-STRAP FOR GROUNDING 1M 1M CONDUCTIVE SHEET Precautions 1-6 1-5-1 Disassembly 1) Remove the power code. 2) Disassemble the Deck-Assy. 3) Solder land 4 points short on Pick-up.(See F

42、ig. 1-4) 4) Disassembly the Pick-up. 1-5-2 Assembly 1) Replace the Pick-up. 2) Remove the soldering 4 points on Pick-up. 3) Reassemble the Deck-Assy. PICK-UP ASSY CD DVD SOLDER LAND 4 POINTS SHORT Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged. Fi

43、g. 1-4 1-5 Pick-up disassembly and reassembly 2-1 2. Product Specifications Power RequirementsAC 120V, 60Hz Power Consumption15W GENERAL Weight2.7kg DimensionsW 430mm X D 240mm X H 79mm Operating Temperature Range+5C +35C Operating Humidity Range10% to 75% DVDReading Speed : 3.49 m/s (Digital Versat

44、ile Disc)Approx. Play Time (Single Sided, Single Layer Disc) : 135 min. CD : 12CmReading Speed : 1.2 to 1.4 m/s DISC (Compact Disc)Maximum Play Time : 74min. CD : 8CmReading Speed : 1.2 to 1.4 m/s (Compact Disc)Maximum Play Time : 20min. VCD : 12Cm Reading Speed : 1.2 to 1.4 m/s Maximum Play Time :

45、74min. (Video + Audio) Composite Video1 channel : 1.0Vp-p (75ohm load) Y : 1.0Vp-p (75ohm load) Video Output Component VideoPr : 0.70Vp-p (75ohm load) Pb : 0.70Vp-p (75ohm load) S-Video Luminance Signal : 1Vp-p (75ohm load) Chrominance Signal : 0.286Vp-p (75ohm load) 2 ChannelL (1/L), R (2/R) * Freq

46、uency Response 48kHz Sampling : 4Hz to 22kHz Audio Output 96kHz Sampling : 4Hz to 44kHz * S/N Ratio110dB * Dynamic Range100dB * Total Harmonic Distortion0.004% * : Nominal specification 3-1 3. Operating Instructions 14 POWER/STANDBY When the unit is first plugged in, the indicator lights. When POWER

47、/STANDBYis pressed, the lamp goes out and the player is turned on. DISC TRAY Press OPEN/CLOSE to open and close the disc tray. DISPLAY Operation indicators are displayed here. OPEN/CLOSE Press to open and close the disc tray. (PLAY/PAUSE) Begin or pause disc play. (STOP) Stops disc play. (SKIP/SEARC

48、H) Use to skip a scene or music. If this button is held down for approx. two seconds, it will switch to the search button: Thereafter, each time the button is pressed, the search speed will switch to 2X, 4X, 8X, 16X, 32X, 128X, after which SKIP will be restored. Description-Front Panel Front Panel C

49、ontrols POWER/STANDBY 15 You can now select different viewing points of the scene recorded by different cameras (Multi Angle). Disc type indicators Reverse playback / Pause / Forward playback Lights when 3D sound is turned on. DVD : Title number DVD : Chapter number. Video/Audio CD : Track number Repeat play mode Linear PCM audio output Dolby Digital audio output DTS (Digital Theater System) audio output(Digital only) MPEG-2 Audio output Displays various messages concerning operations such as PLAY, STOP, LOAD, RANDOM, . no DISC : No disc loaded. OPEN : T