Infinity-IRSV-ps-sm维修电路原理图.pdf

《Infinity-IRSV-ps-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Infinity-IRSV-ps-sm维修电路原理图.pdf（26页珍藏版）》请在收音机爱好者资料库上搜索。

1、IRSV SYSTEM SERVICE MANUAL Infinity Systems Incorporated 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 5/2002 RadioFans.CN 收音机爱 好者资料库 - CONTENTS - SPECIFICATIONS .2 FEATURES.3 IMPEDANCE MATCHING. .5 SET-UP GUIDE.7 OPERATION.14 ADJUSTMENTS/CONTROLS. .15 SERVICE SETTINGS/ADJUSTMENTS/TIPS19 MECH

2、ANICAL PARTS LIST . .20 PASSIVE CROSSOVER SCHEMATIC.21 PASSIVE CROSSOVER WIRING.22 SYSTEM WIRING DIAGRAM.23 ELECTRONIC CROSSOVER SCHEMATIC.24 BASS AMPLIFIER SCHEMATIC .25 RadioFans.CN 收音机爱 好者资料库 1 IRSV SYSTEM SPECIFICATIONS Low Frequency(6) 12” IMG (4 ohm DCR) per tower wired in parallel Midrange Fr

3、equency(12) Emims per mid-twt panel High Frequency(24) Emits (Front) per mid-twt panel (12) Emits (Rear) per mid-twt panel Nominal Impedance 4 ohms (per mid-twt panel) DCR of Woofer Tower0.66 ohms FinishRosewood or Black Dimensions: Woofer tower20 x 28 3/8 x 90” (52.7 x 73 x 228cm) Mid/twt Panel47 x

4、 17 x 90” (119 x 43 x 228cm) Base Footprint38 x 12” (96.5 x 30.5cm) Weight (System)1500 lbs. (681 kg) Special FeaturesMonster Cable ARC wire Solen capacitors Wonder capacitors Frequency response15Hz 45kHz ?2 dB Crossover Frequencies70Hz (Variable) 4500 Hz Crossover ControlsTweeter and Upper Midrange

5、 Level Mid/Twt Amplifier Requirements100-500 watts/ch RMS Bass Amplifier Power2000 watts/ch RMS Production HistoryIntroduced in 1987 Discontinued in 1996 Retail price 1996$60,000.00 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Service Settings/Adjustments/Tips IRSV Amplifier (120v) A036-3089 or (240v)

6、 A036-3096 Potentiometer Settings (Nominal) Most versions have small arrows in the slot of each potentiometer. See illustration for direction of arrows for Nominal Setting. Bottom pot should always be maximum CW. IRS amplifier output can be “trimmed” in relation to each other by powering system up w

7、ith amp cover removed, attaching DMM to main amp terminals and comparing output voltage, driving with 50Hz signal to achieve approx. 5.0 volts at main amp terminals. If amp voltages are not equal on both towers, carefully adjust (raise/lower) Center ACCELERATION/FEEDBACK pot on one unit until they a

8、re. Connect an AC voltmeter to these test points to assure high speed of cooling fan is working. With AC meter attached to these points with COLD system, voltage should be less than 100v. Drive system at 20-30Hz either into woofer tower load or 1-2 ohm 500 watt resistor bank on bench at reasonably h

9、igh power. When system heats sufficiently, warp switch should audibly trip and raise voltage to over 100v. With AC ammeter on 120v power cord, nominal AC current should = 0.40A with no signal input. If not adjust at indicated test point. Line Fuse ratings 120v = 12 amps slo-blo 240v = 8 amps slo-blo

10、 Control Woofer is the third woofer from the bottom in the tower 19 IRSV MECHANICAL PARTS LIST MODEL: IRS V(IF970400) NLA = No Longer Available CABINETS/WINGS/BASES/TOP PIECESNLA FRONT GRILLESNLA CONTROL CABLE (2)NLA AMPLIFIER 120V (2)A036-3089 AMPLIFIER 220V (2)A036-3096 (Currently NLA) ELECTRONIC

11、CROSSOVER UNITA048-3088 TWEETER - EMIT902-3721 (Currently NLA) MIDRANGE - EMIM902-0012D (Currently NLA) 12 WOOFER (10)902-3102 CONTROL WOOFER 12 (2)A028-3103 (Currently NLA) DIAPHRAGM ONLY - TWEETER751-3722 (Currently NLA) DIAPHRAGM ONLY - MIDRANGE751-3806 (Currently NLA) PASSIVE CROSSOVER ASSEMBLY (2)NLA (SEE DRAWING FOR PART NUMBERS OF COMPONENTS) RCA SIGNAL CABLE639-3199 OWNERS MANUAL930-3095 20 PARALLEL 21 22 23 24 25