JVC-FSSD770-cs-sm维修电路原理图.pdf

《JVC-FSSD770-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-FSSD770-cs-sm维修电路原理图.pdf（53页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COMPACT COMPONENT SYSTEM No.20947 Apr. 2001 COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD. FS-SD990 / FS-SD770 FS-SD550 Contents Safety Precautions Important for laser products Preventing static electricity Dismantling and assembling the traverse unit Disassembly method Maintenance of l

2、aser pickup Replacement of laser pickup Flow of functional operation unit TOC read Method of connecting treatment device wire Description of major ICs 1-2 1-3 1-4 1-5 1-6 1-15 1-15 1-16 1-17 1-18 FS-SD990 / FS-SD770 FS-SD550 Area Suffix J C U.S.A Canada These models not have adjustment. The differen

3、ce between FS-SD550 and FS-SD770 FS-SD990 is only the speaker systems. The difference between FS-SD770 and FS-SD990 is cabinets of the speaker. REMOTE CONTROL DIMMERSLEEP DISPLAYFM MODE POWER AHB PROCD PROGRAM DOOR SLIDE AUTO PRESET REPEATRANDOM BASSTREBLECANCEL UP SET DOWN MD/AUXFM / AM VOLUME CD F

4、ADE MUTING FS-SD550 FS-SD770, FS-SD990 REMOTE CONTROL DIMMERSLEEP DISPLAYFM MODE POWER AHB PROCD PROGRAM DOOR SLIDE AUTO PRESET REPEATRANDOM BASSTREBLECANCEL UP SET DOWN MD/AUXFM / AM VOLUME CD FADE MUTING RadioFans.CN 收音机爱 好者资料库 FS-SD990 / FS-SD770 FS-SD550 1-2 1. This design of this product contai

5、ns special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should

6、 be performed by qualified personnel only. 2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of respo

7、nsibility for personal injury or property damage resulting therefrom. 3. Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtaine

8、d by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Par

9、ts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. 4. The leads in the products are routed and dressed with tie

10、s, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that t

11、hey have been returned to normal, after re-assembling. 5. Leakage currnet check (Electrical shock hazard testing) After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, contro

12、l shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the

13、 cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more se

14、nsitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to eachexposed metal part, particularly

15、 any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. voltage measured Any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been

16、 designed and manufactured to meet international safety standards. 2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained. 3. Repairs must be made in accordance with the relevant safety standards. 4. It is essential that safety critical components are

17、replaced by approved parts. 5. If mains voltage selector is provided, check setting for local voltage. Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE ! Burrs formed during molding may be left over on s

18、ome parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( )

19、and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (Except the JC version) RadioFans.CN 收音机爱 好者资料库 FS-SD990 / FS-SD770 FS-SD550 1-3 Important for laser products 1.CLASS 1 LA

20、SER PRODUCT 2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3.CAUTION : There are no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions. 4.CAUTION : The compac

21、t disc player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is

22、 able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. VARNING : Osynlig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen. VARO : Avattaessa ja suojalukitus ohi

23、tettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen. ADVARSEL : Usynlig laserstrling ved bning , nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. ADVARSEL : Usynlig laserstrling ved pning,nr sikkerhetsbryteren er avslott. unng utsettelse for strling. REPRODUCTION

24、 AND POSITION OF LABELS WARNING LABEL DANGER : Invisible laser radiation when open and interlock or defeated. AVOID DIRECT EXPOSURE TO BEAM (e) VARNING : Osynlig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen. (s) VARO : Avattaessa ja suojalukitus ohitettaessa olet altt

25、iina nkymttmlle lasersteilylle.l katso steeseen. (d) ADVARSEL :Usynlig laserstrling ved bning , nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. (f) !CAUTION Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check. FS-SD990

26、 / FS-SD770 FS-SD550 1-4 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.1. Ground

27、ing to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players. Be careful to use proper grounding in the area where repairs are being performed. 1.1.1. Ground the workbench 1. Ground the workbench by laying

28、 conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. 1.1.2. Ground yourself 1. Use an anti-static wrist strap to release any static electricity built up in your body. 1.1.3. Handling the optical pickup 1. In order to main

29、tain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) 2. Do not use a tester to check the condition of the laser diode in the op

30、tical pickup. The testers internal power source can easily destroy the laser diode. 1.2. Handling the traverse unit (optical pickup) 1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nipp

31、ers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may

32、 break when subjected to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it Conductive material (conductive sheet) or iron plate (caption) Anti-static wrist strap FS-SD990 / FS-SD770 FS-SD550 1-5 Dismantling and assembling the traverse

33、unit Notice regarding replacement of optical pickup Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs to the optical

34、pickup or connected devices. 1. Do not touch the area around the laser diode and actuator. 2. Do not check the laser diode using a tester, as the diode may easily be destroyed. 3. It is recommended that you use a grounded soldering iron when shorting or removing the laser diode. Recommended solderin

35、g iron: HAKKO ESD-compatible product 4. Solder the land on the optical pickups flexible cable. Note : Short the land after shorting the terminal on the flexible cable using a clip, etc., when using an ungrounded soldering iron. Note : After shorting the laser diode according to the procedure above,

36、remove the solder according to the text explanation. Shorting Flexible cable KSM-900AAH Sub board (Reverse side) FS-SD990 / FS-SD770 FS-SD550 1-6 Piror to performing the following procedure, remove the CD door. Remove the ten screws B and the five screws C attaching the rear cover on the back of the

37、 body. 1. Removing the rear cover (See Fig.2) Remove the four screws A attaching the CD door on the upper side of the body. 1. Removing the CD door (See Fig.1) Prior to performing the following procedure, remove the CD door, the rear cover. Remove the four screws D attaching the side covers on the b

38、ottom of the body. Move the left cover backward and remove outward. Also remove the right cover in the same way. 1. 2. Removing the right and left covers (See Fig.3) Disassembly method Fig.1 Fig.2 Fig.3 B BB B B B C C C Rear cover D DRight cover Left cover Bottom CD door AA FS-SD990 / FS-SD770 FS-SD

39、550 1-7 Prior to performing the following procedure, remove the CD door, the rear cover and the side covers. Remove the three screws E on the bottom of the body. Release two joints a and two joints b on both sides of the body using a screwdriver and remove the front panel assembly toward the front.

40、1. 2. Removing the front panel assembly (See Fig.4 to 6) Prior to performing the following procedure, remove the CD door, the rear cover, the side covers and the front panel assembly. Disconnect the card wire from connector CN104 and CN105 of the main board in the front part of the body. Disconnect

41、the card wire from CN101 of the main board on the right side, and the wire from CN705 and CN708 of the CD mechanism base assembly respectively. Remove the four screws F attaching the CD mechanism base assembly on the upper side of the body. Remove the screw I attaching the earth terminal on the righ

42、t side. 1. 2. Removing the CD mechanism base assembly (See Fig.7 to 14) Fig.4 Fig.6Fig.5 E Front panel assembly (Left side) (Right side) Front panel assembly Joints a Joints b Bottom Fig.7 Fig.8 FF CD mechanism base assembly CD mechanism base assembly Main bard CN105CN104 Front panel assembly FS-SD9

43、90 / FS-SD770 FS-SD550 1-8 Remove the screw G attaching the power amplifier board on the back of the body. Disconnect the wire from connector CN301 and pull the power amplifier board fully outward. Raise the right and left door arms by turning the gear a in the rear of the power amplifier board. Aft

44、er the CD mechanism base assembly is detached from the door arms, pull the CD mechanism base assembly toward the front and disconnect the wire from connector CN804 on the left side of the door arm board. Pull out the CD mechanism base assembly toward the front. 3. 4. 5. 6. Fig.9 Fig.10 Fig.11 F I CD

45、 mechanism base assembly Main board CN101 CN708 F CD mechanism base assembly CN804 CD mechanism base assembly CN301 G Power amplifier board Fig.13 Gear a Fig.12 Fig.14 CD mechanism base assembly Power amplifier board Door arm Door arm I Gear a CD mechanism base assembly Door arm board (L) CN804 CN70

46、5 FS-SD990 / FS-SD770 FS-SD550 1-9 Prior to performing the following procedure, remove the rear cover, the side covers, the front panel assembly and the CD mechanism base assembly. In case that the upper parts of the door arms attached to the CD door are not level, let down them to the level positio

47、n by turning the gear a in the direction of the arrow. 1. Removing the door arm assembly / the door arm board (R) and (L) (See Fig.15 to 20) When the door arms incline, the door arm assembly and the door arm board (R) and (L) may not be removed. ATTENTION: Remove the four screws H on the upper side

48、and the one screw I on the left side of the body. Remove the four screws J attaching the door arm board (L) and (R) on both sides of the door arm assembly. 2. 3. Fig.15 Fig.16 Fig.18 Fig.20 Fig.17 Fig.19 Door arm Door arm board (L) Door arm Door arm board (R) Door arms (Attached to the CD door) H H

49、Door arm assembly Door arm assembly J J I Door arm board (L) Door arm assembly J J Door arm board (R) Fan motor FS-SD990 / FS-SD770 FS-SD550 1-10 Prior to performing the following procedure, remove the CD mechanism base assembly. Disconnect the wires from connector CN102 and CN193 on the main board and release them from the cord stopper respectively. Remove the two screws K and the two screws L attaching the heat sink a