JVC-DXU10-cs-sm维修电路原理图.pdf

《JVC-DXU10-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-DXU10-cs-sm维修电路原理图.pdf（103页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2008 Victor Company of Japan, Limited No.MB616 2008/4 COMPACT COMPONENT SYSTEM MB61620084 SERVICE MANUAL DX-U10A, DX-U10US, DX-U10UX, DX-U10UG, DX-U10UN, DX-U8US, DX-U8UX, DX-U8UG, DX-U8UN, DX-U6US, DX-U6UX, DX-U6UG, DX-U6UN, DX-U10UH COPYRIGHT 2008 Victor Company of Japan,

2、Limited Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade) TABLE OF CONTENTS 1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34 5TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35 SUPER VIDEO SUPER VIDEO CA-DXU6 SP-DXU6FSP-DXU6F SP-DXU10W CA-DXU8 SP-DXU10FSP-DXU10F SP-DXU10W SP-DXU8S SP-DXU8S SP-DXU10C CA-DXU10 SP-DXU10F SP-DXU10F SP-DXU10W SP-DXU10W SP-DXU10S SP-DXU10S SP-DXU10C RadioFans.CN 收音机爱 好者资料库

6、 1-2 (No.MB616) SPECIFICATION DX-U10/DX-U8 Measured at 1 kHz, with tape recording signal 400 mV Design and specifications are subject to change without notice. Amplifier sectionOutput PowerFRONT SPEAKERS150 W per channel, min. RMS, driven into 4 at 1 kHz with no more than 10% total harmonic distorti

7、on. CENTER SPEAKERCA-DXU10 140 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion. CA-DXU850 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion. SURROUND SPEAKERS CA-DXU10 130 W per channel, min. RMS, driven in

8、to 6 at 1 kHz with no more than 10% total harmonic distortion. CA-DXU850 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion. SUBWOOFERS150 W, min. RMS, driven into 4 at 63 Hz with no more than 10% total harmonic distortion. Digital outputOPTICAL DIGITAL O

9、UTPUT-21 dBm to -15 dBm (660 nm 30 nm) Digital inputUSB memory Audio input sensitivity/ Impedance AUX(STEREO)400 mV/47 k MIC1/MIC23.0 mV/50 k VIDEO OUTColor systemPAL/PAL PROG/NTSC/NTSC PROG selectable VIDEO (composite)1 V(p-p)/75 S-VIDEOY (luminance) : 1 V(p-p)/75 C (chrominance, burst) : PAL : 0.3

10、 V(p-p)/75 C (chrominance, burst) : NTSC : 0.286 V(p-p)/75 COMPONENT (Interlace/Progressive) (Y) : 1 V(p-p)/75 (PB/PR) : 0.7 V(p-p)/75 Speaker Terminals4 - 16 (front speakers/subwoofers) 6 - 16 (surround/center speakers) Tuner sectionFM tuning range87.50 MHz - 108.00 MHz AM (MW) tuning range531 kHz

11、- 1 710 kHz (at 9 kHz) 530 kHz - 1 710 kHz (at 10 kHz) AM (MW) tuning range for Saudi Arabia531 kHz to 1 602 kHz (9 kHz) 530 kHz to 1 600 kHz (10 kHz) Disc/file player section Region codesMiddle East: 2 South East Asia: 3 Central and South America, Australia: 4 Playable discDVD Video/DVD Audio/CD/VC

12、D/SVCD CD-R/CD-RW (CD/VCD/SVCD/MP3/WMA/WAV/JPEG/ MPEG-1/MPEG-2/ASF/DivX format) CD-ROM (MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/ DivX format) DVD-R/-RW (DVD-VR/DVD Video/DVD Audio/MP3/WMA/ WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format) +R/+RW (DVD Video/DVD Audio/MP3/WMA/WAV/JPEG/ MPEG-1/MPEG-2/ASF/DivX format)

13、 DVD-ROM (DVD Video/MP3/WMA/WAV/JPEG/MPEG-1/ MPEG-2/ASF/DivX format) Playable fileMP3, WMA, WAV, JPEG, MPEG-1, MPEG-2, ASF, DivX for- mat Dynamic range80 dB Horizontal resolution500 lines Wow and flutterImmeasurable USB storage sectionUSB specificationCompatible with USB 2.0 Full Speed Compatible de

14、viceMass Storage Class Compatible file systemFAT16, FAT32 Bus power supply5 V / 500 mA Cassette deck section Frequency response: Normal (type I)50 Hz - 14 000 Hz Wow and flutter0.15% (WRMS) GeneralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240 V , (adjustable with the voltage se

15、lector), 50 Hz / 60 Hz Power requirement: For AustraliaAC 240 V , 50 Hz Power consumptionCA-DXU10300 W (at operation) / 22 W (on standby) CA-DXU8270 W (at operation) / 21 W (on standby) Dimensions (W/H/D) (approx.)185 mm 460 mm 370 mm Mass (approx.)CA-DXU1011.5 kg CA-DXU811.4 kg RadioFans.CN 收音机爱 好者

16、资料库 (No.MB616)1-3 DX-U6 Measured at 1 kHz, with tape recording signal 400 mV Design and specifications are subject to change without notice. Amplifier sectionOutput PowerFRONT SPEAKERS150 W per channel, min. RMS, driven into 4 at 1 kHz with no more than 10% total harmonic distortion. SUBWOOFER150 W,

17、 min. RMS, driven into 4 at 63 Hz with no more than 10% total harmonic distortion. Digital outputOPTICAL DIGITAL OUTPUT -21 dBm to -15 dBm (660 nm 30 nm) Digital inputUSB memory Audio input sensitivity/ Impedance AUX400 mV/47 k MIC1/MIC23.0 mV/50 k VIDEO OUTColor systemPAL/PAL PROG/NTSC/NTSC PROG se

18、lectable VIDEO (composite)1 V(p-p)/75 S-VIDEOY (luminance) : 1 V(p-p)/75 C (chrominance, burst) : PAL : 0.3 V(p-p)/75 C (chrominance, burst) : NTSC : 0.286 V(p-p)/75 COMPONENT (Interlace/Progressive) (Y) : 1 V(p-p)/75 (PB/PR) : 0.7 V(p-p)/75 Speaker Terminals4 - 16 (main speakers/subwoofer) 16 - 32

19、(matrix surround speakers) Tuner sectionFM tuning range87.50 MHz - 108.00 MHz AM (MW) tuning range531 kHz - 1 710 kHz (at 9 kHz) 530 kHz - 1 710 kHz (at 10 kHz) AM (MW) tuning range: For Saudi Arabia531 kHz to 1 602 kHz (9 kHz) 530 kHz to 1 600 kHz (10 kHz) Disc/file player section Region codesMiddl

20、e East: 2 South East Asia: 3 Central and South America, Australia: 4 Playable discDVD Video/DVD Audio/CD/VCD/SVCD CD-R/CD-RW (CD/VCD/SVCD/MP3/WMA/WAV/JPEG/MPEG-1/ MPEG-2/ASF/DivX format) CD-ROM (MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX for- mat) DVD-R/-RW (DVD-VR/DVD Video/DVD Audio/MP3/WMA/WAV/ JPEG

21、/MPEG-1/MPEG-2/ASF/DivX format) +R/+RW (DVD Video/DVD Audio/MP3/WMA/WAV/JPEG/MPEG-1/ MPEG-2/ASF/DivX format) DVD-ROM (DVD Video/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ ASF/DivX format) Playable fileMP3, WMA, WAV, JPEG, MPEG-1, MPEG-2, ASF, DivX format Dynamic range80 dB Horizontal resolution500 lines Wow an

22、d flutterImmeasurable USB storage sectionUSB specificationCompatible with USB 2.0 Full Speed Compatible deviceMass Storage Class Compatible file systemFAT16, FAT32 Bus power supply5 V / 500 mA Cassette deck section Frequency response: Normal (type I)50 Hz - 14 000 Hz Wow and flutter0.15% (WRMS) Gene

23、ralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240 V , (adjustable with the voltage selector), 50 Hz / 60 Hz Power requirement: For AustraliaAC 240 V , 50 Hz Power consumption200 W (at operation) 19 W (on standby) Dimensions (W/H/D) (approx.)185 mm 460 mm 370 mm Mass (approx.)10.

24、5 kg 1-4 (No.MB616) SECTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the ma

25、nufacturer. Replacement parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alter

26、ations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tic

27、s are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice M

28、anual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of

29、Service Manual may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazar

30、d. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on the exposed metal part

31、s of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. U

32、sing a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the A

33、C line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth ground. Measure the AC voltage across the resis

34、tor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must n

35、ot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (3) Repairs must be

36、made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some parts of the chassis.

37、 Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diod

38、e ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each exposed metal part.

39、 AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE (No.MB616)1-5 1.5Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (opt

40、ical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs ar

41、e being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any static electricity built up

42、in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a

43、 tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.6Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2

44、) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the

45、connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1.7Attention when traverse unit is decomposed *Please refer to Disassembly method in the text for

46、 the pickup unit. Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short

47、 land sections after connecting the card wire. 1M Conductive material (conductive sheet) or iron palate (caption) Anti-static wrist strap DVD changer mechanism assembly Switch board DVD traverse mechanism assembly DVD servo board 1-6 (No.MB616) 1.8Important for laser products 1.CLASS 1 LASER PRODUCT

48、 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation when open and inter

49、 lock failed or defeated. Avoid direct exposure to beam. 4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may resu