JVC-HXGD8-cs-sm维修电路原理图.pdf

《JVC-HXGD8-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-HXGD8-cs-sm维修电路原理图.pdf（58页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2004 Victor Company of Japan, Limited No.MB277 2004/7 COMPACT COMPONENT SYSTEM MB27720047 HX-GD8 TABLE OF CONTENTS 1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2、 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-

3、8 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40 5TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、. . . . 1-56 Area suffix B - U.K. E - Continental Europe EN - Northern Europe EV - Eastern Europe EE - Russian Federation CA-HXGD8SP-HXGD8SP-HXGD8 RadioFans.CN 收音机爱 好者资料库 1-2 (No.MB277) SPECIFICATION Amplifier section-CA-HXGD7 Design and specifications are subject to change without notice. Output Po

5、werSUBWOOFERS100 W per channel min. RMS driven into 6 at 63 Hz with no more than 10% total harmonic distortion. MAIN SPEAKERS40 W per channel min. RMS driven into 6 at 1 kHz with no more than 10% total harmonic distortion. Audio input sensitivity/impedance (Mea- sured at 1 kHz with tape recording si

6、gnal 300 mV) AUX:300 mV/47 k Digital outputOPTICAL DIGITAL OUTPUT -21 dBm to -15 dBm (660 nm 30 nm) VIDEO OUTColor systemPAL AV OUT (composite)1 V(p-p)/75 (S-VIDEO)Y (luminance):1 V(p-p)/75 C (chrominance burst):0.286 V(p-p)/75 (RGB):0.7 V(p-p)/75 COMPONENT (Interlace/Progressive) (Y):1 V(p-p)/75 (P

7、B/PR):0.7 V(p-p)/75 Speaker TerminalsMAIN SPEAKERS 6 - 16 SUBWOOFERS6 - 16 OthersAV COMPU LINK 2 (3.5) Tuner sectionFM tuning range87.50 MHz - 108.00 MHz AM (MW) tuning range522 kHz - 1 629 kHz Disc player sectionPlayable discDVD Video/DVD Audio/CD/VCD/SVCD CD-R/CD-RW (recorded in Audio CD/Video CD/

8、 Super Video CD/ MP3/ WMA/ JPEG format) DVD-R/DVD-RW (recorded in video format) Dynamic range90 dB Horizontal resolution500 lines Wow and flutterImmeasurable Cassette deck section Frequency response Normal (type I)50 Hz - 14 000 Hz Wow and flutter0.15% (WRMS) GeneralPower requirementAC 230 V 50 Hz P

9、ower consumption185 W (at operation) 25 W (on standby with ECOLOGY mode off) 1.4 W (on standby with ECOLOGY mode on) Dimensions (approx.)205 mm 370 mm 432 mm (W/H/D) Mass (approx.)10.5 kg RadioFans.CN 收音机爱 好者资料库 (No.MB277)1-3 SECTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product

10、 contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Servic

11、es should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufact

12、ure of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tics are often not evident from visual inspection nor can the protection afforded by them necessa

13、rily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice Manual. Electrical components having such features are identified by shading on the schematics

14、and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. (4) The leads in the products are rou

15、ted and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it sh

16、ould be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on the exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, cont

17、rol shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of th

18、e cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more se

19、nsitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particular

20、ly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equi

21、pment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critica

22、l components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4

23、Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing the

24、m, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE 1-4 (No.MB

25、277) 1.5 Safety Precautions (U.K only) (1) This design of this product contains special hardware and many circuits and components specially for safety purposes. For con- tinued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replace- men

26、t parts must be identical to those used in the original circuits. (2) Any unauthorised design alterations or additions will void the manufacturers guarantee; furthermore the manufacturer cannot accept responsibility for personal injury or property damage resulting therefrom. (3) Essential safety cri

27、tical components are identified by ( ) on the Parts List and by shading on the schematics, and must never be replaced by parts other than those listed in the manual. Please note however that many electrical and mechanical parts in the product have special safety related characteristics. These charac

28、teristics are often not evident from visual inspection. Parts other than specified by the manufacturer may not have the same safety characteristics as the recommended replacement parts shown in the Parts List of the Service Manual and may create shock, fire, or other hazards. (4) The leads in the pr

29、oducts are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be obser

30、ved, and it should be confirmed that they have been returned to normal, after re-assembling. 1.5.1Warning (1) Service should be performed by qualified personnel only. (2) This equipment has been designed and manufactured to meet international safety standards. (3) It is the legal responsibility of t

31、he repairer to ensure that these safety standards are maintained. (4) Repairs must be made in accordance with the relevant safety standards. (5) It is essential that safety critical components are replaced by approved parts. (6) If mains voltage selector is provided, check setting for local voltage.

32、 Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. (No.MB277)1-5 1.6Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, f

33、abric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.6.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as

34、 laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground you

35、rself Use an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return

36、the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.7Handling the traverse unit (optical pickup) (1) Do not subject the travers

37、e unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the

38、 traverse unit. Be careful not to take too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1.8Attention when

39、 traverse unit is decomposed *Please refer to Disassembly method in the text for the pickup unit. Apply solder to the short land sections before the flexible wire is disconnected from the connecto on the servo board. (If the flexible wire is disconnected without applying solder, the pickup may be de

40、stroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the flexible wire. 1M Conductive material (conductive sheet) or iron palate (caption) Anti-static wrist strap DVD pickup DVD changer mechanism assembly Short land sections 1-6 (No.

41、MB277) 1.9Important for laser products 1.CLASS 1 LASER PRODUCT 2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3.CAUTION : There are no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete La

42、ser Unit if it malfunctions. 4.CAUTION : The CD,MD and DVD player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CA

43、UTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LABELS CAUTION : Visible and Invisible laser radiat

44、ion when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e) VARNING : Synlig och osynling laserstrlning nr den ppnas och sprren r urkopplad. Betrakta ej strlen. (s) VARO : Avattaessa ja suojalukitus ohitettuna tai viallisena olet alttiina nkyvlle ja nkymttmlle lasersteilylle.

45、Vlt steen kohdistumista suoraan itseesi. (f) ADVARSEL : Synlig og usynlig laserstrling nr maskinen er ben eller interlocken fejeler. Undg direkte eksponering til strling. (d) ! Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check. CLASS 1 LAS

46、ER PRODUCT CAUTION : Visible and Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e) VARNING : Synlig och osynling laserstrlning nr den ppnas och sprren r urkopplad. Betrakta ej strlen. (s) VARO : Avattaessa ja suojalukitus ohitettuna tai viallise

47、na olet alttiina nkyvlle ja nkymttmlle lasersteilylle. Vlt steen kohdistumista suoraan itseesi. (f) ADVARSEL : Synlig og usynlig laserstrling nr maskinen er ben eller interlocken fejeler. Undg direkte eksponering til strling. (d) WARNING LABEL (No.MB277)1-7 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS Th

48、is service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. 1-8 (No.MB277) SECTION 3 DISASSEMBLY 3.1Main body section 3.1.1Removing the metal cover (See Figs.1 to 3) (1) From the back side of the main body, remove the six screws A attaching the metal cover. (See Fig.1.) (2) From the both side

49、s of the main body, remove the two screws B attaching the metal cover. (See Figs.2 and 3.) (3) Remove the metal cover from the main body while lifting the rear section of the metal cover in the direction of the ar- row. (See Figs.2 and 3.) Fig.1 Fig.2 Fig.3 Metal cover A A A Metal cover B Metal cover B (No.MB277)1-9 3.1.2Removing the front panel assembly (See Figs.4 to 7) Prior to performing the f