JVC-HXZ1-cs-sm维修电路原理图.pdf

《JVC-HXZ1-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-HXZ1-cs-sm维修电路原理图.pdf（85页珍藏版）》请在收音机爱好者资料库上搜索。

1、1-1 HX-Z1 SERVICE MANUAL COMPACT COMPONENT SYSTEM No.21088 Jun. 2002 COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD. HX-Z1 HX-Z1 Area Suffix J - U.S.A. C - Canada Safety precautions Preventing static electricity Important for laser products Importance administering point on the safety Disassembly metho

2、d Contents Adjustment method Flow of functional operation until TOC read (CD) Maintenance of laser pickup Replacement of laser pickup Description of major ICs 1-2 1-3 1-4 1-5 1-6 1-24 1-29 1-30 1-30 1-3141 COMPACT DIGITAL AUDIO V O L U M E P R E S E T S O U N D M O D E RadioFans.CN 收音机爱 好者资料库 1-2 HX

3、-Z1 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used

4、in the original circuits. Services should be performed by qualified personnel only. 2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will

5、 further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. 3. Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protectio

6、n afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shadin

7、g on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. 4. The leads in the

8、 products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be ob

9、served, and it should be confirmed that they have been returned to normal, after re-assembling. 5. Leakage currnet check (Electrical shock hazard testing) After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cab

10、inet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock. Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage cur

11、rent from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmet

12、er having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connectio

13、n to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5

14、mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards. 2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained. 3. Repairs must be made in accordance with the relevant safety standards. 4. It is esse

15、ntial that safety critical components are replaced by approved parts. 5. If mains voltage selector is provided, check setting for local voltage. Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE ! Burrs f

16、ormed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with

17、black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. (This regulation does not correspond to J and C version.) RadioFans.CN 收音机爱 好者资料库 1-3 HX-Z1 Preventing static electricity 1. Grounding to prevent damage by static electricity Electrostatic

18、 discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 2. About the earth processing for the destruction prevention by static electric

19、ity In the equipment which uses optical pick-up (laser diode), optical pick-up is destroyed by the static electricity of the work environment. Be careful to use proper grounding in the area where repairs are being performed. 2-1 Ground the workbench Ground the workbench by laying conductive material

20、 (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. 2-2 Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. 3. Handling the optical pickup 1. In order to maintain quality during transport

21、and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) 2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers inte

22、rnal power source can easily destroy the laser diode. 4. Handling the traverse unit (optical pickup) 1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the op

23、tical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to strong

24、force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it Conductive material (conductive sheet) or iron plate (caption) Anti-static wrist strap Attention when traverse unit is decomposed 1. Remove the disk stopper and T. bracket on the CD changer me

25、chanism assembly. 2. Disconnect the harness from connector on the CD motor board. 3. CD traverse unit is put up as shown in Fig.1. 4. Solder is put up before the card wire is removed from connector CN601 on the CD servo control board as shown in Fig. 2. (When the wire is removed without putting up s

26、older, the CD pick-up assembly might destroy.) 5. Please remove solder after connecting the card wire with CN601 when you install picking up in the substrate. *Please refer to Disassembly method in the text for pick-up and how to detach the CD traverse mechanism. Soldering Fig.1 Fig.2 CD changer mec

27、hanism assembly CD traverse unit Flexible cable 1-4 HX-Z1 Important for laser products 1.CLASS 1 LASER PRODUCT 2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3.CAUTION : There are no serviceable parts inside the Laser Unit. Do not dis

28、assemble the Laser Unit. Replace the complete Laser Unit if it malfunctions. 4.CAUTION : The compact disc player uses invisible laserradiation and is equipped with safety switches whichprevent emission of radiation when the drawer is open and the safety interlocks have failed or are de feated. It is

29、 dangerous to defeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. VARNING : Osynlig laserstrlning r d

30、enna del r ppnad och sprren r urkopplad. Betrakta ej strlen. VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen. ADVARSEL : Usynlig laserstrling ved bning , nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling. ADVARSEL : Usynlig

31、laserstrling ved pning,nr sikkerhetsbryteren er avslott. unng utsettelse for strling. REPRODUCTION AND POSITION OF LABELS WARNING LABEL !CAUTION Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check. CLASS 1 LASER PRODUCT 1-5 HX-Z1 Importance

32、administering point on the safety Caution: For continued protection against risk of fire, replace only with same type 2.5A/125V for F103, 5A/125V for F001 and 6A/125V for F101, F102. This symbolspecifies type of fast operating fuse. Precaution: Pour evitisques de fer reux, remplacez le fusible de su

33、rete de F103 comme le meme type que 2.5A/125V, et 5A/125V pour F001 et 6A/125V pour F101, F102. Ce sont des fusibles suretes qui functionnes rapide. 1-6 HX-Z1 Remove the six screws A on the back of the body. Remove the screw B on each side of the body. Remove the metal cover from the body by lifting

34、 the rear part of the cover. 1. 2. 3. Removing the metal cover (See Fig.1 3) Prior to performing the following procedure, remove the metal cover. Disconnect the card wire from connector CN651 on the CD servo control board on the right bottom of the CD changer mechanism assembly. Remove the four scre

35、ws C attaching the CD changer mechanism assembly on top of the body. Remove the CD changer mechanism assembly while lifting the rear part. 1. 2. 3. Removing the CD changer mechanism assembly (See Fig.4, 5) Do not break the front panel tab fitted to the metal cover. CAUTION: Do not damage the CD fitt

36、ing when removing the CD changer mechanism assembly. CAUTION: Disassembly method Metal cover Metal cover Metal cover A A B B CC C A Fig.1 Fig.2 Fig.3 Fig.5Fig.4 Front panel assembly CD changer mechanism assembly Rear part CD changer mechanism assembly CD servo control board CN651 1-7 HX-Z1 Prior to

37、performing the following procedure, remove the metal cover and the CD changer mechanism assembly. Disconnect the card wire from connector CN44 and CN870 on the main board on the right side of the body. Remove the screw D attaching the wire from extending from the underside of the front panel assembl

38、y. Disconnect the wire from connector CN701 on the bridge board. Cut the tie band. Disconnect the wire from connector CN231 and CN232 on the primary board on the left side of the body and remove the band fixing the wire. Remove the plastic rivet attaching the inner bar in the center of the front pan

39、el assembly. 1. 2. 3. 4. 5. Remove the three screws E attaching the front panel assembly at the bottom of the body. Release the two joints a on the lower left and right sides of the front panel assembly using a screwdriver, and remove the front panel assembly toward the front. 6. 7. Removing the fro

40、nt panel assembly (See Fig.6 9) Front panel need to be tilt a little bit as release from bottom chassis. REFERENCE: Keep the plastic rivet for reuse.REFERENCE: Front panel assembly Front panel assembly Front panel assembly Front panel assembly Fig.6 Fig.7 Fig.8 Fig.9 Bridge board CN701 Bridge board

41、CN701 Main board CN870 D E Joint a Joint a Primary board CN231, CN232 Primary board CN231, CN232 Plastic rivet Band Inner bar Bottom chassis 1-8 HX-Z1 Prior to performing the following procedure, remove the metal cover. Disconnect the card wire from connector CN1 on the antenna board on the right si

42、de of the body. Remove the band attaching the antenna board. Remove the two screws F on the rear panel on the back of the body. 1. 2. 3. Removing the antenna board (See Fig.10, 11) There is no need to remove the CD changer mechanism assembly. REFERENCE: Fig.10 Fig.11 Rear panel Rear panel CN1 Antenn

43、a board Band F 1-9 HX-Z1 Prior to performing the following procedure, remove the metal cover and the CD changer mechanism assembly. Remove holding board by remove two plastic rivets and then slide out the holding board as shown in fig. 12. Disconnect fan wire from connector CN206. Cut off the tie ba

44、nd that tied fan wire on inner bar. Remove eight screws F from rear panel. Detach joint b to release rear panel from inner bar. Release joints c which on right bottom and left bottom of rear panel. The joint can be release by pull outward the side of rear panel. 1. 2. 3. 4. 5. 6. Removing the rear p

45、anel (See Fig.12 17) Fan assembly will come off with rear panel. REFERENCE: Fig.12 Fig.15 Fig.13 Fig.14 Fig.16 Fig.17 Inner bar Holding board Holding board CN206 Plastic Rivets Tie band Joint b Fan assembly Rear panel Rear panel Rear panel F F F F Joint c Joint c CN206 1-10 HX-Z1 Prior to performing

46、 the following procedure, remove the metal cover and the CD changer mechanism assembly and the rear panel. Remove two screws G on the rear panel. Rotate fan assembly in clockwise direction to release fan assembly from rear panel (joint d). 1. 2. Removing the fan assembly (See Fig.18, 19) Prior to pe

47、rforming the following procedure, remove the metal cover, the CD changer mechanism assembly, the antenna board and the rear panel. Disconnect the card wire from connector CN44 and CN870 on the main board. Remove the screw D attaching the board. Disconnect connector CN217 and CN311 on the main board

48、outward and release from the base chassis (joint e) upward. 1. 2. 3. Removing the main board (See Fig.20) Rear panel G Fig.18 Fig.19 Fig.20 Joint d Joint d Fan assembly CN217 CN311 CN44 Joint eD Main board CN870 1-11 HX-Z1 Prior to performing the following procedure, remove the metal cover, the CD c

49、hanger mechanism assembly, the rear panel, the antenna board and main board. Remove the plastic rivet attaching the stay inner bar and remove the screw H on the bridge board. Move the inner bar forward and upward to release from the front section (joint f) and from the bridge board (two joints h) respectively. Remove the two plastic rivets setting the holding board fixing the bridge board and the primary