JVC-RX5062S-avr-sm维修电路原理图.pdf

《JVC-RX5062S-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-RX5062S-avr-sm维修电路原理图.pdf（14页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COPYRIGHT 2006 Victor Company of Japan, Limited No.MB504 2006/2 AUDIO/VIDEO CONTROL RECEIVER MB50420062 RX-5060BJ,RX-5060BC, RX-5060BE,RX-5062SB, RX-5062SE,RX-5062SEN, RX-5062SEV Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) TABLE OF CONTENTS

2、 1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、1-6 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、 . . . . . . . . 1-13 5TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 TA/NEWS/INFO DISPLAY MODE RadioFans.CN 收音机爱 好者资料库 1-2 (No.MB504) SPECIFICATION Northern america version Amplifier Output Power

5、 Front channels100 W per channel, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmonic distortion. Center channel100 W, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmon- ic distortion. Surround channels100 W per channel, min. RMS, driven int 8 , at 1 kHz with

6、no more than 10% total harmonic distortion. AudioAudio Input Sensitivity/Impedance (1 kHz)CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 220 mV/47 k Audio Input (DIGITAL IN)*CoaxialDIGITAL 1 (DVD) : 0.5 V(p-p)/75 OpticalDIGITAL 2 (CD) : -21 dBm to -15 dBm (660 nm 30 nm) Recording Output LevelTAPE/CDR, VCR

7、: 220 mV Signal-to-Noise Ratio (66 IHF/78 IHF)CD, TAPE/CDR, VCR, TV SOUND, DVD : 62 dB/71 dB Frequency Response (8 )CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 20 Hz to 20 kHz (1 dB) Equalization (5 bands)63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz : 8 dB (in 2 dB steps) VideoVideo Input Sensitivity/Impedance C

8、omposite video DVD, VCR, AUX : 1 V(p-p)/75 Video Output LevelComposite video VCR, MONITOR OUT : 1 V(p-p)/75 SynchronizationNegative Signal-to-Noise Ratio45 dB FM tuner (IHF) Tuning Range87.5 MHz to 108.0 MHz Usable SensitivityMonaural12.8 dBf (1.2 V/75 ) 50 dB Quieting SensitivityMonaural16.0 dBf (1

9、.7 V/75 ) Stereo37.5 dBf (20.5 V/75 ) Stereo Separation at OUT (REC)35 dB at 1 kHz AM tuner Tuning Range530 kHz to 1 710 kHz General Power RequirementsAC 120V , 60 Hz Power Consumption155 W/200 VA (at operation) 0.8 W (in standby mode) Dimensions (W H D)435 mm 146.5 mm 369.5 mm Mass7.0 kg RadioFans.

10、CN 收音机爱 好者资料库 (No.MB504)1-3 Europian version * Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency?32 kHz, 44.1 kHz, 48 kHz) Designs and specifications are subject to change without notice. Amplifier Output Power Front channels100 W per channel, min. RMS, dr

11、iven into 8 , at 1 kHz with no more than 10% total harmonic distortion. Center channel100 W, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmon- ic distortion. Surround channels100 W per channel, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmonic distortion. A

12、udioAudio Input Sensitivity/Impedance (1 kHz)CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 220 mV/47 k Audio Input (DIGITAL IN)CoaxialDIGITAL 1 (DVD) : 0.5 V(p-p)/75 OpticalDIGITAL 2 (CD) : -21 dBm to -15 dBm (660 nm 30 nm) Recording Output LevelTAPE/CDR, VCR : 220 mV Signal-to-Noise Ratio (66 IHF/DIN)CD,

13、 TAPE/CDR, VCR, TV SOUND, DVD : 66 dB/62 dB Frequency Response (8 )CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 20 Hz to 20 kHz (1 dB) Equalization (5 bands)63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz : 8 dB (in 2 dB steps) VideoVideo Input Sensitivity/Impedance Composite video DVD, VCR, AUX : 1 V(p-p)/75 Video

14、Output LevelComposite video VCR, MONITOR OUT : 1 V(p-p)/75 SynchronizationNegative Signal-to-Noise Ratio45 dB FM tuner (IHF) Tuning Range87.50 MHz to 108.00 MHz Usable SensitivityMonaural17.0 dBf (1.9 V/75 ) 50 dB Quieting SensitivityMonaural21.3 dBf (3.2 V/75 ) Stereo41.3 dBf (31.8 V/75 ) Stereo Se

15、paration at OUT (REC)35 dB at 1 kHz AM (MW) tuner Tuning Range522 kHz to 1 629 kHz General Power RequirementsAC 230 V , 50 Hz Power Consumption140 W (at operation) 0.8 W (in standby mode) Dimensions (W H D)435 mm 146.5 mm 369.5 mm Mass7.0 kg 1-4 (No.MB504) SECTION 1 PRECAUTION 1.1Safety Precautions

16、(1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used i

17、n the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and wi

18、ll further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tics are often not evident from visual inspection nor can the prot

19、ection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice Manual. Electrical components having such features are identifie

20、d by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. (4) Th

21、e leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dres

22、s should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on the exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, sc

23、rew heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from

24、 each exposed metal parts of the cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter ha

25、ving, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each

26、 exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.

27、m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It i

28、s essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- for

29、ming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical

30、 for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 150

31、0 10W 0.15 F AC TYPE (No.MB504)1-5 1.5Importance administering point on the safety Graphic symbol mark (This symbol means fast blow type fuse.) FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSES ; should be read as follows ; F201,F206,F207: 5A 125V F202,F2

32、03 : 2A 125V F201,F206,F207: 5A 125V F202,F203 : 2A 125V Full Fuse Replacement Marking FUSE CAUTION Le symbole graphique (Ce symbole signifie fusible de type a fusion rapide.) POUR UNE PROTECTION CONTINUE CONTRE DES RISQUES DINCENDIE, REMPLACER SEULEMENT PAR UN FUSIBLE DU MEME TYPE ; Marquage Pour L

33、e Remplacement Complet De Fusible PRECAUTIONS SUR LES FUSIBLES doit etre interprete comme suit ; CN251 FC272 FC221 FC222 FC231 FC232 FW201 R201 FC261 110111112113114120121122130131 FC262 FC271 FC211 FC212 R1 EP1 B106 B105 B104 TA201TA202 PW104 PW102 PW105 PW103 PW101 B103 B102 B101 B108 B107 B109 B1

34、10 1-6 (No.MB504) SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. (No.MB504)1-7 SECTION 3 DISASSEMBLY 3.1Main body 3.1.1Removing the top cover (See Fig. 1 and 2) (1) Remove the three screws A attaching the top cover. (2) Remove the four sc

35、rews B attaching the both side of top cover. Fig.1 Fig.2 A B 1-8 (No.MB504) 3.1.2Removing the front panel assembly (See Fig. 3 to 5) (1) Remove the three screws C attaching the top side of front panel assembly. (2) Remove the four screws D attaching the bottom side of front panel assembly. (3) Remov

36、e the one screw E attaching the ground wire to front chassis. (4) Disconnect the connector to CN404 of audio board, CN504 of video board, CN402 of main board and CN201 of regu- lator board. Fig.3 Fig.4 Fig.5 C D E CN504 CN404 CN402 CN201 Regulator board Main board (No.MB504)1-9 3.1.3Removing the rea

37、r panel and each I/O boards (See Fig. 6 to 8) (1) Remove the two screws F attaching the tuner board. (2) Disconnect the card wire from CN411 of main board. (3) Remove the three screws G attaching the digital board. (4) Disconnect the connector CN481 and CN482 of main board. (5) Remove the four screw

38、s H attaching the main board and remove the one screw J attaching the ground wire to front board. (6) Disconnect the connector CN421 of main board. (7) Remove the two screws K attaching the subwoofer board. (8) Disconnect the connector CN431 of main board. (9) Remove the three screws L attaching the

39、 video board (for European model, two screws L see Fig. 8) (10) Remove the two screws M attaching the speaker terminal board. (11) Remove the one screw N attaching the fuse board. (12) Remove the three screws P attaching the rear panel. Fig.6 Fig.7 Fig.8 GFKJHLM CN481 CN482 CN421 CN431 CN441 CN411 D

40、igital board Audio board Subwoofer board Tuner Video board K 1-10 (No.MB504) 3.1.4Removing the main board (See Fig. 9) (1) Disconnect the connector CN471, CN472 and CN473 from front board. (2) Disconnect the connection board from CN291 of regulator board and CN491 of main board. (3) Remove the two s

41、crews Q and one screw R attaching the main board. Fig.9 3.1.5Removing the front board and heat sink (See Fig. 10) (1) Disconnect the connector from CN203 and CN241 of reg- ulator board. (2) Disconnect the connector from CN251 of transformer board. (3) Remove the four screws S attaching the heat sink

42、. (4) Remove the one screw T attaching the front board. Fig.10 CN491 CN291 RQ CN471 CN472 Main board Regulator board Connection board CN473 CN241 CN203 CN251 Trans board Regulator board Front board Heat sink T S S (No.MB504)1-11 3.1.6Removing the power transformer and regulator board (See Fig. 11 an

43、d 12) (1) Remove the four screws U attaching the power transform- er. (2) Remove the one screw V attaching the fuse board. (3) Remove the three screws W and one screw X attaching the regulator board. (4) Disconnect the wire from CN101 of headphone board. Fig.11 Fig.12 3.1.7Removing the headphone boa

44、rd (See Fig. 13) (1) Remove the nut Y attaching the head phone board. Fig.13 V UU Fuse board Power trans CN101 W WX Regulator board Headphone jack Y 1-12 (No.MB504) 3.2Front panel assembly 3.2.1Removing the micon board (See Fig. 14 and 16) (1) Take out the volume knob from front panel assembly. (2)

45、Remove the nut Z attaching the volume. (3) Remove the nine screws AA attaching the micon board. 3.2.2Removing the power switch board (See Fig. 15) (1) Remove the two screws BB attaching the power switch board. 3.2.3Removing the AUX board (See Fig. 14 and 16) (1) Take out the multi jog knob from fron

46、t panel assembly. (2) Remove the three screws CC attaching the AUX board. Fig.14 Fig.15 Fig.16 Volume knob Multi jog knob Z AA BB Power switch board Micon boardAux board (No.MB504)1-13 SECTION 4 ADJUSTMENT This service manual does not describe ADJUSTMENT. SECTION 5 TROUBLESHOOTING This service manual does not describe TROUBLESHOOTING. (No.MB504) Audio/Video Systems Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Victor Company of Japan, Limited VPT Printed in Japan