JVC-RX7020VBK-avr-sm维修电路原理图.pdf

《JVC-RX7020VBK-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-RX7020VBK-avr-sm维修电路原理图.pdf（61页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL AUDIO/VIDEO CONTROL RECEIVER No.21075 Mar. 2002 COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD. RX-7020VBK RX-7020VBK Contents Safety precautions -1-2 Importance administering point on the safety - 1-3 Disassembly method -1-4 Adjustment method -1-9 Description of major ICs -1-1024 Area s

2、uffix J - U.S.A. DVDVCRTV SOUND/DBS ADJUST RX-7020VAUDIO/VIDEO CONTROL RECEIVER SETTING MASTER VOLUME CONTROL DOWNUP CDTAPE/CDR SOURCE NAME BASS BOOST INPUT ANALOG/DIGITAL SPEAKERS ON/OFF SURROUND MODE PHONES SURROUND ON/OFF FM/AM TUNING STANDBY STANDBY/ON FM/AM PRESETFM MODE MEMORY INPUT ATT FM/AM

3、DVD MULTI PHONO SOURCE NAME 12 COMPULINK Remote CONTROL 231 564 897/P 0+1010 BASS BOOSTEFFECT MENU ENTER TEST REARL + DIMMER SUB WOOFER + REARR + MUTING CHTV VOL /REWFF/ VOLUME CA TV/DBS CONTROL TV/VIDEO REC PAUSE RETURNFM MODE100+ CONTROL A/V CONTROL RECEIVER RM-SRX7020J REMOTE CONTROL CATV/DBSVCRT

4、VAUDIO SURROUND MODEINPUTON/OFF DVD MULTIDVDCD TAPE/CDR TREBLE TV/DBSVCRPHONO FM/AM BASS SURROUNDANALOG/DIGIT ALSLEEP CENTER + TUNING SOUND RadioFans.CN 收音机爱 好者资料库 RX-7020VBK 1-2 1. This design of this product contains special hardware and many circuits and components specially for safety purposes.

5、For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only. 2. Alterations of the design or circuitry

6、 of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. 3. Many electr

7、ical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacemen

8、t parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not ha

9、ve the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. 4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temp

10、erature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after re-assembling. 5. Leakage currnet check (Ele

11、ctrical shock hazard testing) After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electric

12、al shock. Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the chassis, t

13、o a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15

14、 F AC-type capacitor between an exposed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and meausre the AC vol

15、tage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has been designed and manufactured to meet international safety standards. 2. It is the leg

16、al responsibility of the repairer to ensure that these safety standards are maintained. 3. Repairs must be made in accordance with the relevant safety standards. 4. It is essential that safety critical components are replaced by approved parts. 5. If mains voltage selector is provided, check setting

17、 for local voltage. Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE ! Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre

18、forming repair of this system. In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. (This regulat

19、ion does not correspond to J and C version.) RadioFans.CN 收音机爱 好者资料库 RX-7020VBK 1-3 Caution: For continued protection against risk of fire, replace only with same type 6.3A/125V for F201, 2A/125V for F202 and F203. This symbol specifies type of fast operating fuse. Precaution: Pour eviter risques de

20、 feux, remplacez le fusible de surete de F201 comme le meme type que 6.3A/125V, et 2A/125V pour F202 et F203. Ce sont des fusibles suretes qui functionnes rapide. Importance administering point on the safety Secondary parts Primary part FC211 FC212 R1 EP1 B106 B105 B104 TA201 TA202 PW104 PW102 PW105

21、 PW103 PW101 B103 B102 B101 B108 B107 B109 B110 CN251 D205 FC221 FC222 FC231 FC232 R201 RY201 110 111112113 114120 121 122 130131 B192 B191 B160 B159 6.3A-125V 2A-125V 2A-125V F 201 F 203 F 202 LVA1029-C9 LVA1029-C7 6.3A-125V RX-7020VBK 1-4 Remove the four screws A attaching the top cover on both si

22、des of the body. Remove the three screws B on the back of the body. Remove the top cover from behind in the direction of the arrow while pulling both sides outward. 1. 2. 3. Disassembly method Removing the top cover (See Fig.1) Prior to performing the following procedure, remove the top cover. Remov

23、e the power cord stopper from the rear panel by moving it in the direction of the arrow. Remove the thirty-two screws E attaching the each boards to the rear panel on the back of the body. Remove the four screws F attaching the rear panel on the back of the body. 1. 2. 3. Removing the rear panel (Se

24、e Fig.4) Prior to performing the following procedure, remove the top cover. Disconnect the card wire from connector CN402 on the audio board and CN201 on the power supply board in the front panel assembly. Cut off the tie band fixing the harness. Remove the three screws C attaching the front panel a

25、ssembly. Remove the four screws D attaching the front panel assembly on the bottom of the body. Detach the front panel assembly toward the front. 1. 2. 3. 4. Removing the front panel assembly (See Fig.2 and 3) Fig.1 Fig.2 Fig.3 Fig.4 A 2 A 2 B Top cover C Power supply board Audio board CN402 Main bo

26、ard Tie band D E E FEF F Cord stopper C Front panel assembly Front panel assembly D Rear panel CN201 EEEE E RX-7020VBK 1-5 Prior to performing the following procedure, remove the top cover and the rear panel. Cut off the tie band fixing the harness. Disconnect the DSP board from connector CN481 on t

27、he audio board. Disconnect the audio input board, DVD board Video board and the S video board from connector CN421, CN431, CN441 and CN461 on the audio board. Disconnect the Component video board from connector CN511 on the S video board. Disconnect the tuner board from connector CN411 on the audio

28、board. 1. 2. 3. 4. 5. Removing each board connected to the rear side of the audio board (See Fig.5 to 9) Fig.5 Fig.6 Fig.7 Fig.8 CN411 Tie band DSP board DVD board Video board Tuner board Audio input board DSP board CN481 CN441CN431CN421 CN481 CN421 CN431 CN441 CN411 Tie band CN421 CN431 CN441 Audio

29、 input board DVD board Video board Tuner board Audio board CN461S Video board CN461 S Video board Component video board CN511 Fig.9 Component video board CN511 RX-7020VBK 1-6 Prior to performing the following procedure, remove the top cover and the rear panel. Removing the audio board (See Fig.10) D

30、isconnect the card wire from connector CN402 on the audio board. Disconnect the relay board from the audio board and the power supply board. (CN291, CN491) Disconnect the harness from connector CN471, CN472, CN473. Remove the three screws G attaching the audio board assembly. Remove the screw H atta

31、ching the audio board assembly. 1. 2. 3. 4. 5. Removing the Heat sink (See Fig.12 to 14) Prior to performing the following procedure, remove the top cover, the rear panel and audio board. Disconnect the harness from connector CN241 and CN203 on the power supply board respectively. Disconnect the har

32、ness from connector CN251 on the power transformer board . Remove the four screws I and the two screws J attaching the main board. 1. 2. 3. Removing the main board (See Fig.11) Prior to performing the following procedure, remove the top cover and main board. Remove the two screws K attaching the hea

33、t sink to the reverse side of main board. Disconnect the for connectors with each amp. board, and remove the main board. Remove the four screws M and ten screws L attaching the heat sink. 1. 2. 3. Fig.10 Fig.13 Fig.11 Fig.12 power supply board Power / Fuse board Relay board CN473 Audio board Main bo

34、ard rear side Main board Heat sink CN291 CN203 CN491H G CN471 CN402 CN472 Power transformer G G CN241I I I I J J LL KK M M CN251 L Fig.14 Main board Rear Rch amp. board Front Lch amp. board Front Rch amp. board Center amp. board Rear Lch amp. board Heat sink CN802 CN801 CN302 CN301 CN901 RX-7020VBK

35、1-7 Prior to performing the following procedure, remove the top cover and the rear panel. Remove the screw O attaching the power / fuse board. Unsolder the power cord and other harnesses connected to the power / fuse board. 1. 2. Removing the power / fuse board (See Fig.15) Prior to performing the f

36、ollowing procedures, remove the top cover. Cut off the tie band fixing the harness. Unsolder the two harnesses connected to the power transformer. Unsolder the harness connected to the FW201 on the power transformer board. Remove the four screws N attaching the power transformer. 1. 2. 3. 4. Removin

37、g the power transformer (See Fig.15) Prior to performing the following procedure, remove the top cover and the front panel. Remove the one nut attaching the headphone jack of the power supply board on the front side of the body. Disconnect the harness connected to connector CN241, CN201, CN203, and

38、CN291 on the power supply board (If necessary, cut off the band fixing the harness on the side of the base chassis). Remove the three screws P attaching the power supply board and pull out the power supply board from the front bracket backward. Unsolder the three harnesses connected to the power sup

39、ply board. 1. 2. 3. 4. Removing the power supply board (See Fig.16 , 17) Fig.15 Fig.16 Fig.17 Power supply board Power transformer N CN241 Solder points N Solder points Solder points O Power / fuse board Power cord Power supply board Nut Headphone jack Headphone jack Tie band Solder points P P P Sol

40、der points CN201 CN291 Hook Power transformer board FW201 CN203 RX-7020VBK 1-8 Prior to performing the following procedure, remove the top cover and the front panel assembly. Pull out the volume knob on the front side of the front panel and remove the nut attaching the system control board. Remove t

41、he two screws Q attaching the power switch board. Disconnect the harness from connector CN714 on the power switch board. Remove the six screws R attaching the system control board on the back of the front panel. On the back of the front panel, release the six joints by pushing the joint tabs inward.

42、 Remove the operation switch panel toward the front. Release the two hook attaching the system control board. 1. 2. 3. 4. 5. 6. Removing the system control board / power switch board (See Fig.18 to 20) Fig.18 Fig.19 Fig.20 Front panel assembly Nut Volume knob System control board Power switch board

43、R R CN714 Q Joint Joint JointJointJointJoint Hook Hook Operation switch panel RX-7020VBK 1-9 Adjustment method 1. Set the volume control to minimum during this adjustment. (No signal & No load) 2. Set the surround mode OFF. 3. Turn VR301 and VR302 fully counterclockwise to warm up before adjustment.

44、 If the heat sink is already warm from previous use the correct adjustment can not be made. 4. For L-ch, connect a DC voltmeter between TP301s B216 and B217 (Lch) and, connect it between TP302s B218 and B219 (Rch). 5. Adjust the VR301 (Lch) and VR302 (Rch) so that the DC voltmeter indicates 2.0mV im

45、mediately after turning the power on. 1. Tuner range FM 87.5MHz108.0MHz AM (MW) 530kHz1710kHz Tuner section Power amplifier section TP302 (Rch) VR301 (Lch) VR302 (Rch) Heat sink Adjustment of idling current Measurement locationTP301 (Lch) , TP302 (Rch) Adjustment partVR301 (Lch) , VR302 (Rch) Attent

46、ion This adjustment does not obtain a correct adjustment value immediately after the amplifier is used (state that an internal temperature has risen). Please adjust immediately after using the amplifier after turning off the power supply of the amplifier and falling an internal temperature. * It is

47、not abnormal though the idling current might not become 0mA even if it is finished to turn variable resistance (VR301, VR302) in the direction of counterclockwise. TP301 (Lch) RX-7020VBK 1-10 1 2 3 4 5 6 7 8 9 10 11 33 32 31 30 29 28 27 26 25 24 23 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39

48、38 37 36 35 34 1.Pin layout AK4527BVQP (IC601) : A/D,D/A converter Top View No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Symbol SDOS OSKS MIS BICK LRCK SDTI1 SDTI2 SDTI3 SDTO D,AUX DFS DEMI DEMO MCKO DVDD DVSS PD XTS SDTO Source Select Pin (Note 1) L : Internal ADC output, H : DAUX input Control Mode Select Pin L : 3-wire Serial, H : I2C Bus Soft Mute Pin (Note 1), Connect to GND When this pin goes to H, soft mute cycle is initialized. When returning to L, the output mute releases. Audio Serial Data Clock Pin