Onkyo-DBS30.1-br-sm维修电路原理图.pdf

《Onkyo-DBS30.1-br-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Onkyo-DBS30.1-br-sm维修电路原理图.pdf（56页珍藏版）》请在收音机爱好者资料库上搜索。

1、DBS-30.1 SERVICE MANUALSERVICE MANUAL RC-731DV BLU-RAY DISC PLAYER MODEL DBS-30.1(B)CDD1N Ref. No. 4150 July, 2009 Black model 120 V AC, 60HzB CDD1N SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTR

2、IC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. RadioFans.CN 收音机爱 好者

3、资料库 TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1-1 Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、. . . . . . . . . . . . . . . . . . . .1-2-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、. . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4-1 Cabinet Disassembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5-1 How to Initialize the BLU-RAY Disc Player . . . . . . . . . . . . . . . . . . . . .

6、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7-1 Block Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8-1 Schematic Diagrams / CBA and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9-1 Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . .

8、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10-1 Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11-1 Electrical Parts List . . . . . . . .

9、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12-1 Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. RadioFans.CN 收音机爱 好者资料库 1-1-1E5K55SP SPECIFICATIONS

10、1-2-1B2NLBSP LASER BEAM SAFETY PRECAUTIONS This BD player uses a pickup that emits a laser beam. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look

11、 directly at the laser beam. CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Location: Inside Top of BD mechanism. Do not look directly at the laser beam coming from the pickup or allow it to strike against

12、your skin. Drive Mechanism Assembly Laser Beam Radiation Laser Pickup Turntable 1-3-1BDN_ISP IMPORTANT SAFETY PRECAUTIONS Product Safety Notice Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection

13、they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the

14、 recommended replacement part might create shock, fire, and/or other hazards. The Products Safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are carefully inspected to confirm with the recognized product safety

15、and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Re

16、place only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and

17、noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation tape 2) PVC tubing 3) Spacers 4) Insulators

18、for transistors E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F.Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.). G. Check th

19、at replaced wires do not contact sharp edges or pointed parts. H. When a power cord has been replaced, check that 5 - 6 kg of force in any direction will not loosen it. I.Also check areas surrounding repaired locations. J.Be careful that foreign objects (screws, solder droplets, etc.) do not remain

20、inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC outlet. 1-3-2BDN_ISP Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been ret

21、urned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d) between soldered terminals, and between

22、 terminals and surrounding metallic parts. (See Fig. 1) Table 1: Ratings for selected area Note:This table is unofficial and for reference only. Be sure to confirm the precise values. 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug pr

23、ongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Measuring Method (Power ON): Insert load Z between B (earth ground, po

24、wer cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table. Table 2: Leakage current ratings for selected areas Note:This table is unofficial and for reference only. Be sure to confirm the precise values. AC L

25、ine VoltageClearance Distance (d), (d) 120 V 3mm(d) 4mm(d) AC Line VoltageLoad ZLeakage Current (i) One side of power cord plug prongs (B) to: 120 V 2k RES. Connected in parallel i0.7mA AC Peak i2mA DC RF or Antenna terminals 50k RES. Connected in parallel i0.7mA AC Peak i2mA DC A/V Input, Output Ch

26、assis or Secondary Conductor Primary Circuit Fig. 1 dd Fig. 2 AC Voltmeter (High Impedance) Exposed Accessible Part B One side of Power Cord Plug Prongs Z 1-4-1BDN_SN STANDARD NOTES FOR SERVICING Circuit Board Indications 1.The output pin of the 3 pin Regulator ICs is indicated as shown. 2.For other

27、 ICs, pin 1 and every fifth pin are indicated as shown. 3.The 1st pin of every male connector is indicated as shown. Instructions for Connectors 1.When you connect or disconnect the FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord. 2.FFC (Flexible Foil Connector) cable sh

28、ould be inserted parallel into the connector, not at an angle. Pb (Lead) Free Solder When soldering, be sure to use the Pb free solder. How to Remove / Install Flat Pack-IC 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: 1.Prepare the hot-air flat pack-IC desoldering machine, then apply ho

29、t air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) 2.Remove the flat pack-IC with tweezers while applying the hot air. 3.Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then

30、 remove (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CAUTION: 1.The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2.Do not supply hot air

31、to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) Top View OutIn Bottom View Input 5 10 Pin 1 Pin 1 FFC Cable Connector CBA * Be careful to avoid a short c

32、ircuit. Fig. S-1-1 1-4-2BDN_SN 3.The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. With Soldering Iron: 1.Using desoldering braid, remove the solder from all pins of the flat pack-IC. When yo

33、u use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2.Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air

34、desoldering machine. (Fig. S-1-4) 3.Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4.Release the flat pack-IC from the CBA using tweezer

35、s. (Fig. S-1-6) Hot-air Flat Pack-IC Desoldering Machine CBA Flat Pack-IC Tweezers Masking Tape Fig. S-1-2 Flat Pack-IC Desoldering Braid Soldering Iron Fig. S-1-3 Fine Tip Soldering Iron Sharp Pin Fig. S-1-4 1-4-3BDN_SN With Iron Wire: 1.Using desoldering braid, remove the solder from all pins of t

36、he flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2.Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 3.While heating the pins using a fine tip soldering iron or hot air blower, pull up the

37、wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 4.Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted)

38、. (Fig. S-1-6) 5.Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is a

39、pplied. 2. Installation 1.Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2.The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB

40、 when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3.Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. To Solid Mounting Point Soldering Iron Iron Wire or Hot Air Blower Fig. S-1-5 Fine Tip Soldering Iron C

41、BA Flat Pack-IC Tweezers Fig. S-1-6 Example : Pin 1 of the Flat Pack-IC is indicated by a mark. Fig. S-1-7 Presolder CBA Flat Pack-IC Fig. S-1-8 1-4-4BDN_SN Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by ele

42、ctrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper groun

43、ding (1 M) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. CBA Grounding Band Conductive Sheet or Coppe

44、r Plate 1M 1M CBA 1-5-1E5K55DC CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally. 2. Disass

45、embly Method Note: (1) Identification (location) No. of parts in the figures (2) Name of the part (3) Figure Number for reference (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector * = U

46、nhook, Unlock, Release, Unplug, or Desolder e.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2) (5) Refer to “Reference Notes.” Reference Notes 1.CAUTION 1: Locking Tabs (L-1) and (L-2) are fragile. Be careful not to break them. 2.The BD Main CBA electrical components having such feature

47、s are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create sho

48、ck, fire, or other hazards. Notes: 1.Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2.All resistance values are indicated in ohms (K = 103, M = 106). 3.R

49、esistor wattages are 1/4W or 1/6W unless otherwise specified. 4.All capacitance values are indicated in F (P = 10-6 F). 5.All voltages are DC voltages unless otherwise specified. 1-9-2BDN_SC LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES DINCELE NUTILISER QUE DES FUSIBLE DE MME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED. 2. CAUTION: Fixed Voltage (or Auto voltage selectable)