GrundigSonoclock52SC5302 维修电路图、原理图.pdf

上传人:cc518 文档编号:110000 上传时间:2024-07-20 格式:PDF 页数:10 大小:1.92MB
下载 相关 举报
GrundigSonoclock52SC5302 维修电路图、原理图.pdf_第1页
第1页 / 共10页
GrundigSonoclock52SC5302 维修电路图、原理图.pdf_第2页
第2页 / 共10页
GrundigSonoclock52SC5302 维修电路图、原理图.pdf_第3页
第3页 / 共10页
亲,该文档总共10页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《GrundigSonoclock52SC5302 维修电路图、原理图.pdf》由会员分享,可在线阅读,更多相关《GrundigSonoclock52SC5302 维修电路图、原理图.pdf(10页珍藏版)》请在收音机爱好者资料库上搜索。

1、Sonoclock 52 SC 5302 Service Document Exchange Set Es gelten die Vorschriften und Sicherheitshinweise gem dem Service Manual Sicherheit, Material- nummer 720108000000, sowie zustzlich die even- tuell abweichenden, landesspezifischen Vorschrif- ten! The regulations and safety instructions shall be va

2、lid as provided by the Safety Service Manual, part number 720108000000, as well as the respective national deviations. S Dieses Service Dokument ist nur in Datenform verfgbar This Service Document is only available as data nderungen vorbehalten/Subject to alteration Made by GRUNDIG in Germany H-S43

3、0303 S Service Manual Sicherheit Safety Materialnr./Part No. 720108000000 ? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? Sonoclock 52 SC 5302? EQUIPMENT REQUIRED Signal Source 1. FM signal ge

4、nerator (FM SG) 2. Sweep generator (10.7 Mhz for FM) Output Indicator 1. SSVM 2. Oscilloscope 3. Frequency Counter General preparation 1. Check source voltage. 2. Set function switch to band being aligned 3. Turn volume control to minimum (unless noted otherwise) 4. Connect low side of signal and ou

5、tput indicator to chassis ground unless otherwise specified. Keep ground connection close to high side connection. 5. Keep signal inout as low as possible to avoid and AFC action (set output indicator to high sensitivity.) 6. Standard modulation is 1000 Hz AT 22.5KHZ amplitude for FM FM ALIGNMENT PR

6、OCEDURE Step Signal source (FM RF Gen.) Connect to Set signal to Alignment Indicator connect to Oscilloscope or SSVM Set Radio dial to AdjustAdjust forRemarks 1T1Maximum Symmetrical response 2det. Coil Symmetrical response centered 10.7Mhz 3Repeat Step 1 and 2 as necessary to obtain S curve linearit

7、y , with maximum output FM RF ALIGNMENT Step Signal source (FM Signal Gen.) Connect to Set signal to Alignment indicator (oscilloscope , VTVM Connect to Set radio dial to AdjustAdjust for Remarks 1 87.35 MHz modulated 87.35MHz (lowest end) L7 (Osc, coil) 2 108.25MHz modulated 108.25MHz (Highest end)

8、 C2 (Osc, trimmer) 3 90 MHz modulated 90MHz L3 (RF coil) stretch or squeeze 4 106 MHz modulated 106MHzC1 (RF trim) 5repeat steps 3 and 4 as necessary to minimum tracking error. Also repeat steps 1 and 2 if necessary. * UK models must not be able to tune below 87.5 MHz. Quiet point ALIGNMENT PROCEDUR

9、E MODEL NO. GRUNDIG SONOCLOCK SC 52 Volume control min- position TP2 and GND Sweep centered 10.7 MHz TP3 Detector Output Terminal TP 1, GND (Test point) through matching network if necessary Across speaker voice coilMaximum Volume control Max- position Sonoclock 52 SC 5302? 1 9 8 12 19 7 24 10 23 38 18 13 14 5 2830 33 25 3 34 26 31 39 40 29 274 371617153611 35 20 21 22 32 2 6

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 德国收音机 > 根德GRUNDIG

copyright@ 2008-2025 收音机爱好者资料库 版权所有
备案编号:鄂ICP备16009402-5号