JBL Technical Note - Vol.1, No.2 电路原理图.pdf

《JBL Technical Note - Vol.1, No.2 电路原理图.pdf》由会员分享，可在线阅读，更多相关《JBL Technical Note - Vol.1, No.2 电路原理图.pdf（20页珍藏版）》请在收音机爱好者资料库上搜索。

1、Technical Notes Vol. 1, No. 2 70-Volt Distribution Systems Using JBL Industrial Series Loudspeakers Theory of Line Distribution Systems In a typical paging, background music, or noise-masking system, many loudspeakers are placed across a single amplifier. They must often be powered at different leve

2、ls, and the calculations involved in determining the actual load impedance at the amplifiers output are quite tedious. The 70-volt distribution system was developed to make all calculations simple and straightforward. In this method of distribution, the output of an amplifier is designed so that its

3、 full power output exists at a voltage of 70 volts RMS, as shown in Figure 1. Table I shows the load impedances which correspond to several output power ratings. In application, many loudspeakers are placed across the output using distribution transformers, which matches the load impedance of each l

4、oudspeaker so that it will draw a specified amount of power from the line. Figure 2A shows a typical distrubution transformer which has two primary taps (for different line levels) and multiple secondary taps for different power drives to the loudspeaker. Figure 2B shows a different transformer arra

5、ngement, which power settings made in the primary and loudspeaker impedance matching in the secondary. The configuration at A allows the same transformer to be operated with 25-volt systems, while the configuration at B allows the same transformer to be used with loads of different impedances. Both

6、types provide identical turns ratios when used in the 70-voIt-8-ohm configuration. Let us assume that we want to drive a particular loudspeaker at 5 watts. The connection is made as shown in Figure 3, and the impedance of the loudspeaker as seen from the primary side is calculated as shown. Note tha

7、t the 8-ohm loudspeaker is transformed across to the primary as a 1000-ohm load to the amplifier. The 70-volt primary has, in the process, been transformed down to 6.3 volts RMS at the voice coil. Loudspeakers are placed across the line and tapped as needed, and all the designer has to do is simply

8、count watts. When the total wattage drawn by the line equals the power output rating of the amplifier, then the proper load will exist at the amplifiers output. The simplicity of the method is that the user need never calculate load impedances and their parallel combinations. Use of the 25-Volt Tap

9、Just as a 70-volt amplifier produces its full output at 70-volts RMS, a 25-volt amplifier produces its full output at 25-volts RMS. Because wiring codes do not require conduit for voltages up to 25-volts RMS, the 25-volt system has been incorporated into some distribution systems, particularly schoo

10、l systems. Assume for example that we have a 200-watt amplifier with a 25-volt output. Then the load impedance for full output will be: Z = E 2/P = (25)2/200 = 3.13 ohms Transformer and Line Losses 70-volt line-to-loudspeaker transformers in the 5-watt class should exhibit nominal insertion losses n

11、o greater than 1 or 1.25 dB, and the frequency response should be uniform from 40 Hz to 12 kHz. The distortion should be less than 0.1% at mid-frequencies, rising to no more than 5% at 40 Hz. Figure 4 shows a schematic of the JBL 9315HT transformer designed to be used with the JBL 8000-series of ind

12、ustrial loudspeakers. Table 2 gives the published specifications for this transformer. Measurements are an actual production unit are given in Table III, and for comparison we show, in Table IV, similar measurements on a Soundolier Model HT-47 transformer. The transformers are comparable except for

13、the total harmonic distortion (THD) at 40 Hz at high drive levels. Wire losses in 70-volt systems should be held to no more than 0.5 dB. The trade-off here is obviously between the cost of power and the cost of copper wiring. Actually, the losses at the loudspeaker come from two sources: power loss

14、in the lines and power not delivered by the amplifier due to the load mismatch. The data presented in Table V gives the maximum length of wire pairs that will ensure losses in a 70-volt system not exceeding 0.5 dB. We can use Table V to determine maximum wire runs for different gauges in 25-volt sys

15、tems by: 1. Dividing all lengths by 8 2. Dividing maximum safe power by 2.8 3. Dividing the load impedance by 8 Loudspeakers Used in Distributed Systems Because they are generally low-power units, and used in relatively large quantities, loudspeakers used in low-1 eve I distributed systems tend to b

16、e selected on a very competitive basis. It is not unusual to see equivalent models by several manufacturers priced within pennies of each other. While there is certainly justification in not using costly cast frame loudspeakers for paging systems, there is absolutely no reason why performance charac

17、teristics have to be compromised to the extent usually seen in this segment of the professional sound industry. JBLs 8000-series industrial grade loudspeakers are both cost competitive and, as will be seen, show a performance edge over the general level of competitive products: 100 mm (4) diameter l

18、oudspeakers The curves shown in Figure 5A, B, and C show the performance of the JBL model 8110 loudspeaker. Note at A the smooth response through the mid-range. The on-axis rise above 4 kHz is generally beneficial in that it is 2 associated with maintaining extended power response out to the 6-8 kHz

19、 region. The off-axis response is shown at B. Second and third harmonic distortion for 10-watts input is shown at C. The distortion is this figure has been raised 20 dB for ease in reading. Note that above 400 Hz the distortion components are in the 1 to 2% range. Figure 5D, E, and F show equivalent

20、 measurements for the Soundolier model FC-104, and Figure 5G, H, and J show equivalent data for the Altec model 405-8H. Note that both competitive models show a considerable dip in their output in the 800 Hz to 1500 Hz range. These dips, which are almost an octave wide, occur in the frequency range

21、so important to speech articulation. They are due to improperly controlled surround resonances in the loudspeakers. The off-axis behavior of all three models is equivalent, since it is basically a function of cone diameter. Distortion data for the the Soundolier and Altec models shows a rise in the

22、400 Hz to 4 kHz range relative to the JBL 8110H. 200 mm (8) diameter, 142 g (5 oz) magnet, loudspeakers Figure 6A, B, and C present data on the JBL 8120H, while D, E, and F and G, H, and J show data, respectively, on the Soundolier model FD and the Altec 2549A. Note the smooth mid-range response of

23、the JBL 8120H as compared with both competitive models. Off-axis behavior of all three loudspeakers is equivalent, since they are all single cone designs. The 10-watt distortion performance of the JBL 8120H is marginally better than the Soundolier FD and significantly better than the Altec 2549A. 20

24、0 mm (8), 283 g (10 oz) magnet, loudspeakers Figure 7A, B, and C present data on the JBL model 8130H, while D, E, and F and G, H, and J present data, respectively, on the Soundolier model C10 and the Muzak C8M10/U704. Again, note the overall smoothness of the JBL model compared to the other two. Off

25、-axis performance is again similar between the models. The distortion performance is unusual. The JBL model shows fairly constant distortion in the range from 400 Hz to 10 kHz. The Soundolier and Muzak models exhibit extremely low distortion in the range from 200 Hz to 800 Hz. Above that range, the

26、distortion rises dramatically. 200 mm (8) coaxial loudspeakers Figure 8A, B, and C show performance data on the unique JBL 8140 Co-motional 2-way design, while D, E, and F and G, H, and J show data, respectively, on the Soundolier C803 and the Altec 409-T. While nearly all 200 mm coaxials have a sta

27、tionary HF element located on a bridge which extends across the frame, the JBL 8140 has its HF element, a piezoelectric device, attached directly to the LF cone near its apex. This design eliminates interference in the crossover region due to the bridge, and the near-coincidence of both HF and LF el

28、ements results in a very smooth transition between the two, as can be seen from a comparison of the on-axis data for all three models. The Co-motional design is subject to Doppler distortion while the two competitive models are not. We have assured ourselves that LF cone excursions normally encounte

29、red in distributed systems are small enough so that any modulation of the HF due to LF cone motion will be insignificant. All the models exhibit smooth off-axis response since they all have the benefit of a separate small HF radiator. 3 Conclusion With the new 8000-series industrial products line, J

30、BL confirms its belief that quality performance in low-level distributed systems need not cost any more than the mediocre performance which has become the norm for this important segment of sound contracting work. JBL is further the only manufacturer of industrial grade loudspeakers to publish Thiel

31、e-Small parameters for these products, thus enabling contractors and consultants to custom design enclosures for optimum LF performance. IN FIGURE 1. A 70-VOLT AMPLIFIER TABLE I. POWER Z 50 W 100 n 100 W 50 n 200 W 25 a 250 W 20 a 400 W 12.5 n FIGURE 2. TYPICAL 70-VOLT DISTRIBUTION TRANSFORMERS Z E

32、0 = 70 VOLTS POWER = E2 = 5000 Z Z Z = 5000 POWER 70 V 25 V 5 W 2 W 1 W .5 W 0.5 W 1 W 2 W 5W 1 6 0 8 n 4fi A B 4 E = 70 V Zi = 5000 = 1000 n 5 E S = VPZ = V 5(8) = 6.3 V RMS FIGURE 3. PLACING A 5-WATT LOAD ACROSS A 70-VOLT LINE TABLE II. INSERTION LOSS (70-VOLT PRIMARY) FOR JBL 9315HT TRANSFORMER T

33、AP TYPICAL MAXIMUM DRAWS FROM LINE DELIVERS TO LOAD 5 W 1.0 dB 1.25 dB 5 W 4 W 2 W 0.7 dB 1.0 dB 2 W 1.7 W 1 W 0.7 dB 1.0 dB 1 W 0.85 W 0.5 W 1.0 dB 1.25 dB 0.5 W 0.4 W FIGURE 4. JBL MODEL 9315HT TRANSFORMER 5 5 W 8 n Z|_ 70 V 25 V 0 5 W (OdB) 2 W ( - 4 d B ) 1 W ( - 7 d B ) .5W ( - 1 0 dB) 0 8J2 LO

34、AD TABLE III. JBL MODEL 9315HT FREQUENCY 0.5 W 1 W 2 W 5 W 40 Hz -0.1 dB* -0.1 dB* -0.1 dB* 0 dB* 60 -0.1 0 -0.1 0 200 -0.1 0 0 0 1 K 0 0 0 0 2 K 0 0 0 0 5 K 0 0 0 0 8 K -.05 - . 1 -0.12 -0.15 10 K -.05 -.13 -0.19 -0.23 12 K -.15 -.165 -0.23 -0.31 INSERTION LOSS, 1 kHz 1.1 dB 0.6 dB 0.5 dB 0.9 dB TH

35、D 40 Hz, 5 WATTS = 0.9% *DATA NORMALIZED TO 1 kHz TABLE IV. SOUNDOLIER MODEL HT-47 FREQUENCY 0.5 W 1 W 2 W 4W 40 Hz 0 dB* 0 dB* -0.12 dB* -0.55 dB* 60 0 0 0 0 200 0 0 0 0 1 K 0 0 0 0 2 K 0 0 0 0 5 K -0.1 -0.16 - 0.25 -0.26 8 K -0.3 -0.43 -0.5 -0.55 10 K -0.6 -0.67 -0.8 - 0.8 12 K -0.8 -0.95 -1.1 -1.

36、1 INSERTION LOSS, 1 kHz 0.85 dB -0.45 dB -1.4 dB -1.1 dB THD 40 Hz, 4 WATTS = 15% *DATA NORMALIZED TO 1 kHz TABLE V. MAXIMUM WIRE RUNS FOR 0.5 dB LOSS IN 70-VOLT SYSTEMS WIRE SIZE, AWG RESISTANCE PER 300 m (1000) PAIR OF COPPER WIRE MAXIMUM CURRENT MAXIMUM POWER 50 W 100 W 200 W 250 W 400W 10 2.0 OH

37、MS 25 AMP. 1750 W 870 m 435 m 220 m 175 m 110 m (2900) (1450) (730) (580) (370) 12 3.2 OHMS 20 AMP. 1400 W 545 m 272 m 140 m 110 m 70 m (1820) (910) (460) (365) (230) 14 5.2 OHMS 15 AMP. 1000 W 335 m 168 m 85 m 68 m 42 m (1120) (560) (280) (225) (140) 16 8.0 OHMS 6 AMP. 420 W 220 m 110 m 55 m 45 m 2

38、7 m (740) (370) (180) (150) (90) 18 13.0 OHMS 3 AMP. 210 W 170 m 85 m . (560) (230) 20 20.6 OHMS 1 AMP. 70 W 66 m 33 m (220) (110) JBL 8110H 40 FIGURE 5A FIGURE 5B FIGURE 5C 7 SOUNDOLIER FCM04 8 FIGURE 5F FIGURE 5D FIGURE 5E FIGURE 5H FIGURE 5J 9 ALTEC 405-8H FIGURE 5G JBL 8120H FIGURE 6A FIGURE 6B

39、FICURE 6C 10 FIGURE 6D SOUNDOLIER FD FIGURE 6E FIGURE 6F 11 FIGURE 6G FIGURE 6H 12 FIGURE 6J ALTEC 2549A FIGURE 7C 13 JBL 8130H FIGURE 7A FIGURE 7B SOUNDOLIER C10 FIGURE 7D FIGURE 7E 14 FIGURE 7F 10000 FIGURE 7G 1000 * 10000 FIGURE 7H FIGURE 7J JBL 8140 100 1000 10000 FIGURE 8A 100 1000 IOOOO FIGURE

40、 8B Bruel & Kjcer Hz 16 FIGURE 8C SOUNDOLIER C803 FIGURE 8D FIGURE 8E FIGURE 8F 17 FIGURE 8G 18 ALTEC 409-T FIGURE 8H FIGURE 8J NOTES 19 P R O F E S S I O N A L D I V I S I O N JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A. UBL/harman international 2M 63810 6/84 Printed in U.S.A.