SONY MZ-N1电路原理图 .pdf

《SONY MZ-N1电路原理图 .pdf》由会员分享，可在线阅读，更多相关《SONY MZ-N1电路原理图 .pdf（64页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL PORTABLE MINIDISC RECORDER AEP Model UK Model E Model SPECIFICATIONS MZ-N1 US and foreign patents licensed from Dolby Laboratories. Continued on next page Model Name Using Similar MechanismNEW Mechanism TypeMT-MZN1-171 Optical Pick-up NameLCX-5R Ver 1.0 2002. 01 9-873-443-01Sony Corpo

2、ration 2002A0500-1Personal Audio Company C 2002.1Published by Sony Engineering Corporation OpenMG, “MagicGate”, “MagicGate Memory Stick”, “Memory Stick”, VAIO,MusicClip and their logos are trademarks of Sony Corporation. “WALKMAN” is a trademark of Sony Corporation. Microsoft,Windows,Windows NT and

3、Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. IBM and PC/AT are registered trademarks of International Business Machines Corporation. Macintosh is a trademark of Apple Computer,Inc.in the United States and/or other countri

4、es. All other trademarks are trademarks of their respective owners. and marks are omitted in this manual. Audio playing system MiniDisc digital audio system Laser diode properties Material: GaAlAs Wavelength: = 790 nm Emission duration: continuous Laser output : less than 44.6 W (This output is the

5、value measured at a distance of 200 mm from the lens surface on the optical pick-up block with 7 mm aperture.) Recording and playback time (when using MDW-80) Maximum 160 min. in monaural Maximum 320 min. in stereo Revolutions 382 rpm to 2,700 rpm (CLV) Error correction ACIRC (Advanced Cross Interle

6、ave Reed Solomon Code) Sampling frequency 44.1 kHz Sampling rate converter Input: 32 kHz/44.1 kHz/48 kHz Coding ATRAC (Adaptive TRansform Acoustic Coding) ATRAC3 LP2/LP4 本资料由O K X I A 视听皮带资源库w w w . o k x i a . c n 提供 本资料由视听皮带资源库 收集整理提供 2 MZ-N1 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED

7、 BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. Modulation system EFM (Eight to Fourteen Modulation)

8、 Frequency response 20 to 20,000 Hz 3 dB Wow and Flutter Below measurable limit Inputs1) MIC: stereo mini-jack (minimum input level 0.25 mV) Line in: stereo mini-jack for anolog input (minimum input level49 mV) optical (digital) mini-jack for optical (digital) input Outputs i/LINE OUT2): stereo mini

9、-jack (dedicated remote control jack)/194 mV (10 kohm) Maximum output (DC) 2) Headphones:5 mW + 5 mW (16 ohm) Power requirement Sony AC Power Adaptor connected at the DC IN 3V jack (country model in parentheses): 220 V AC, 50/60 Hz (Continental Europe) 230 - 240 V AC, 50 Hz (U.K. and Hong Kong) 100

10、- 240 V AC, 50/60 Hz (Other countries) Battery life1) When recording2) (Unit: approxi.hours)(JEITA3) BatteriesSP Stereo LP2 Stereo LP4 Stereo Nickel metal hydride rechargeable battery4) 121721 LR6 (SG) Sony alkaline dry battery5) 121923 Nickel metal hydride rechargeable battery4) + One LR6 (SG)5) 30

11、4352 The recorder: Nickel metal hydride rechargeable battery NH-14WM(A) 1.2V 1350 mAh (MIN) Ni- MH LR6 (SG) alkaline battery USB cradle: AC power adaptor DC 3V Dimensions Approx. 77.7 71.4 16.4 mm (w/h/d) (31/8 27/8 21/32 in.) Mass Approx. 87 g (3.0 oz) the recorder only 1)The LINE IN (OPT) jack is

12、used to connect either a digital (optical) cable or a line (analog) cable. 2)The i/LINE OUT jack connects either headphones/earphones or a line cable. Design and specitications are subject to change without notice. Supplied accessories AC power adaptor (1) Headphones/earphones with a remote control

13、(1) Optical cable (1) USB cable (1) Nickel metal hydride rechargeable battery NH-14WM(A) (1) CD-ROM (1)* Dry battery case (1) Rechargeable battery carrying case (1) Carrying pouch/carrying case with a belt clip (1) *Do not play a CD-ROM on an audio CD player. 1)The battery life may be shorter due to

14、 operating conditions and the temperature of the location. 2)When you record , use a fully charged rechargeable battery. Recording time may differ according to the alkaline batteries. 3)Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries Association) standa

15、rd. 4)When using a 100% fully charged nickel metal hydride rechargeable battery (NH- 14WM(A). 5)When using a Sony LR6 (SG) “STAMINA” alkaline dry battery (produced in Japan). When playing (Unit BatteriesSP Stereo LP2 Stereo LP4 Stereo Nickel metal hydride rechargeable battery2) 303842 LR6 (SG) Sony

16、alkaline dry battery3) 445262 Nickel metal hydride rechargeable battery2) + One LR6 (SG)3) 7995110 1)Measured in accordance woth theJEITA (Japan Electronics and Information Technology Industries Association) standard. 2)When using a 100% fully charged nickel metal hydriderechargeable battery (NH- 14

17、WM(A). 3)When using a Sony LR6 (SG) “STAMINA” alkaline dry battery (produced in Japan) : approxi.hours)(JEITA1) 本资料由视听皮带资源库 收集整理提供 3 MZ-N1 TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL.5 3.DISASSEMBLY 3-1.Disassembly Flow .6 3-2.Bottom Panel Assy .7 3-3.Upper Panel Section.7 3-4.LCD Module, Upper

18、Panel Assy .8 3-5.MAIN Board Section .8 3-6.Battery Case Assy, MAIN Board.9 3-7.MD Mechanism Deck (MT-MZN1-171), Chassis Assy.9 3-8.OP Service Assy (LCX-5R). 10 3-9.Holder Assy . 11 3-10. DC Motor (Sled) (M602). 11 3-11. DC SSM18B Motor (Spindle) (M601), DC Motor (Over Write Head UP/DOWN) (M603) . 1

19、2 4.TEST MODE. 13 5.ELECTRICAL ADJUSTMENTS. 19 6.DIAGRAMS 6-1.Block Diagram SERVO/USB Section . 30 6-2.Block Diagram AUDIO Section . 31 6-3.Block Diagram DISPLAY/KEY CONTROL/ POWER SUPPLY Section . 32 6-4.Note for Printed Wiring Board and Schematic Diagrams . 33 6-5.Printed Wiring Board MAIN Board (

20、Component Side) . 34 6-6.Printed Wiring Board MAIN Board (Conductor Side) . 35 6-7.Schematic Diagram MAIN Board (1/4) . 36 6-8.Schematic Diagram MAIN Board (2/4) . 37 6-9.Schematic Diagram MAIN Board (3/4) . 38 6-10. Schematic Diagram MAIN Board (4/4) . 39 6-11. IC Pin Function Description . 46 7.EX

21、PLODED VIEWS 7-1.Upper Panel Section. 53 7-2.Bottom Panel Section. 54 7-3.Chassis Section . 55 7-4.MAIN Board Section . 56 7-5.MD Mechanism Deck Section (MT-MZN1-171) . 57 8.ELECTRICAL PARTS LIST. 58 CAUTION Use of controls or adjustments or performance of procedures other than those specified herei

22、n may result in hazardous ra- diation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur- in

23、g repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the sol

24、der contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering

25、 irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C . Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong

26、 viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. On power s

27、ources Use house current, nikel metal hydride rechargeable battery, LR6 (SG) battery, or car battery. For use in your house: For the supplied battery charging stand, use the AC power adaptor supplied with this recorder. Do not use any other AC power adaptor since it may cause the recorder to malfunc

28、tion. Polarity of the plug 本资料由视听皮带资源库 收集整理提供 4 MZ-N1 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the

29、human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK Never look into the laser diode emiss

30、ion from right above when checking it for adjustment. It is feared that you will lose your sight. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK (LCX-5R) The laser diode in the optical pick-up block may suffer electro- static break-down easily. When handling it, perform soldering bridge to the laser-ta

31、p on the flexible board. Also perform mea- sures against electrostatic break-down sufficiently before the op- eration. The flexible board is easily damaged and should be handled with care. OPTICAL PICK-UP FLEXIBLE BOARD SECTION 1 SERVICING NOTES In performing the repair with the power supplied to th

32、e set, re- moving the MAIN board causes the set to be disabled. In such a case, fix a convex part of the open/close detect switch (S804 on MAIN board) with a tape in advance. Handle the FLEXIBLE board (overwrite head) with care, as it has been soldered directly to the MAIN board. In repairing the co

33、mponent side of MAIN board, connect the FLEXIBLE board (overwrite head) and the MAIN board with the lead wires in advance. (See page 8) laser-tap upper panel assy MAIN board Tape S804 FLEXIBLE board (Over write head) Replacement of CXD2677-202GA (IC801) used in this set re- quires a special tool. Th

34、e shipment data will be cleared when the NV is reset. There- fore, change the NV adjusted values following the Change of NV Adjusted Values immediately after the NV was reset. (See page 19) This set requires the patch data in the nonvolatile memory (IC802) to be rewritten using the application, when

35、 the MAIN board or nonvolatile memory (IC802) was replaced. (See page 27) System requirements IBM PC/AT or Compatible (The software does not run on Macintosh.) CPU: MMX Pentium 233 MHz or higher (Pentium II 400 MHz or higher is recommended.) Hard disk drive space: 60 MB or more (The amount of necess

36、ary space depends on the version of the Windows OS or the size of your audio files.) RAM: 64 MB or higher (128 MB or higher is recommended for Windows XP Home Edition/Windows XP Professional.) CD-ROM drive (capable of digital playback by WDM) Sound Board USB port (supports USB 2.0 Full Speed (previo

37、usly USB 1.1) Operating System: Windows 98/Windows 98 Second Edition/Windows 2000 Professional/Windows Me/Windows XP Home Edition/Windows XP Professional (manufacturer installed) The NTFS format of Windows 2000 Professional, Windows XP Home Edition, or Windows XP Professional (manufacturer-installed

38、) is supported only when used with the standard (factory) settings. This software is not supported by the following environments. Windows 95, Windows NT, or other versions of Windows NT (such as Server) An environment that is an upgrade of the original manufacturer-installed operating system, as in

39、the following examples: Windows 3.1/Windows 95 t Windows 98 (or Windows 98 Second Edition/ Windows Me) Windows Me/Windows 2000 Professional t Windows XP Multi-boot environment with Windows 2000 (or Windows XP) and Windows 98 (or Windows 98 Second Edition/WindowsMe) Display: High (16bit) Color or mor

40、e (800 480 dot or more) Internet access: for Web registration and EMD services Windows Media Player (version 7.0 or higher) installed for playing WMA files. Notes Trouble-free operation is not assured within a multiple-monitor environment. We do not assure trouble-free operation for all computers sa

41、tisfying the system requirements. Trouble-free operation is not guaranteed following the self-conducted upgrade of home-built PCs or operating systems. We do not assure trouble-free operation of the system suspend, sleep, or hibernation function on all computers. For details, refer to “Net MD Help”

42、of the online help. Note The optical digital output connector (on computers provided with one) may be disabled during playback for the protection of copyrights. Notes on using OpenMG Jukebox with Windows 2000/Windows XP If your computer is Windows 2000 Professional, Windows XP Home Edition, or Windo

43、ws XP Professional, please be aware of the following before instaling OpenMG Jukebox. 1 With Windows 2000 Professional, you must log on as “Administrators” (or with the user name “Administrator”) to install OpenMG Jukebox. 2With Windows XP Home Edition or Windows XP Professional, you must log on wit

44、h user name “Computer Administrator” to install OpenMG Jubebox. To check whether a user name has the attribute of “Computer Administrator” or not, go to Control Panel - User Account. Notes on using OpenMG Jukebox with Windows XP/ Windows Me If Windows XP/Windows Me is installed in your computer, and

45、 you perform the “System Restore” function of the Windows “System Tools,” the songs managed by OpenMG Jukebox may become corrupted and rendered unplayable. Therefore, before executing “System Restore,” back up the songs using “OpenMG Jukebox Backup Tool” first. Then, after the “System Restore” function is finished, restore the songs using “OpenMG Jukebox Backup Tool” to ensure the integrity and r