BO-Beolab2_type686x-from19367810-sm维修电路原理图.pdf

《BO-Beolab2_type686x-from19367810-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《BO-Beolab2_type686x-from19367810-sm维修电路原理图.pdf（20页珍藏版）》请在收音机爱好者资料库上搜索。

1、BeoLab 2 Type 6861, 6862, 6863, 6864, 6865, 6867From serial no. 19367810Service Center repair guide EnglishABO-CENTER v/HENRIKSENS ELEKTRONIKRadioFans.CN 收音机爱 好者资料库HOW TO SERVICEBig efforts have been made to introduce the highest quality and a low call rate. Therefore this product is suitable for th

2、e new Service Strategy which benefi ts the customer. In a service situation where there is an electrical fault in a BeoLab 2, the fault can be removed during one visit to the customers home if you bring a Back-up suitcase with you. If it is a mechanical fault, the particular part can be replaced in

3、the customers home.When the necessary part(s) arrive from service stock, the visit to the customers home can be arranged.Front line serviceThe BeoLab 2 must be serviced in the customers home when dealing with electrical faulty or the exchange of mechanical parts. In this way, you avoid having to tra

4、nsport the heavy subwoofer (18kg) back and forth from the customer (box size: L 310 x W 260 x H 315 mm).In the customers home, it is possible to exchange the driver and slave units, the electrical chassis or transformer, as well as exchange the cabinet and foot. Replacement of the cabinet can be don

5、e easily at the customers home as it contains all the necessary parts. Only the loudspeaker units, the electrical chassis and the transformer must be put into the new cabinet.Electrical partsFor front line service we offer a Back-up suitcase (also applies to BeoLab 1). All the needed electrical part

6、s are located in the Back-up suitcase (loudspeaker units and electronics).That means the BeoLab 2 Back-up suitcase must be ordered and returned.Service documentationService documentation for the BeoLab 2 is this guide (with part numbers for the Back-up suitcase and mechanical parts) and the Users Gu

7、ide.How to service, English 1.1ABO-CENTER v/HENRIKSENS ELEKTRONIKRadioFans.CN 收音机爱 好者资料库Specifi cation guidelines for service use 1.9SPECIFICATION GUIDELINE FOR SERVICE USE BeoLab 2Type no. See type surveyDimensions W x H x D / Weight 260 x 315 x 310 mm / 17.7 kgCabinet fi nish Aluminium, structure

8、painted, greyPower Consumption Typical: 15 watts IEC65: 62W Stand-by: 0.4 wattsMaximum Sound Pressure Level 110 dBPower amplifi ers 1Long-term maximum output power 850 wattsEffective Frequency range 23 - 120 HzCabinet principle Double balanced passive radiator systemMagnetically shielded YesWoofer 1

9、 x 9” (250 mm) fl at diaphragmPassive radiators 2 x 9” (250 mm) fl at diaphragmNet volume 13 litresBass equalization ABL (Adaptive Bass Linearization)Switch for loudspeaker position Free, Wall or CornerInput sensitivity Adjustable by three position switch Corresponding to 83 dB, 88 dB or 91 dB for m

10、ain speakersConnectionsPower Link - Input 1Power Link - Output 2Mains 1Power Link plug Pin 1 Loop through, Power Link plugs Pin 2 Signal GND Pin 3 Audio Left 0V - 2V RMS Pin 4 Power Link speaker ON = 0.5V, OFF = ?A?BC?DE?)?G?0?G?)?S.S?P?.7?L?)BeoLab 2?TU.?A?BC?DE?)?G?0?,$?)?HG?de?07ABO-CENTER v/HENR

11、IKSENS ELEKTRONIK6.2 DisassemblyDisassembly 6.26.2DISASSEMBLY1346Left5LeftFrontExtra rubber foot fromthe back-up suitcaseLeftLeftPUSH2RightThe NTC-PCB must be connectedwhen the chassis is in service positionready for voltage measuringRight798WARNING!The mechanical limit for the driver is easily reac

12、hed when the vacuum tightness in BeoLab 2 is brokenSpecial bezel-toolSTATIC ELECTRICITYMAY DESTROY THEPRODUCTLeftExtra rubber foot fromthe back-up suitcase1011TORX 25TORX 25TORX 25TORX 25TORX 25TORX 25TORX 25TORX 25ALLENKEY 5ALLENKEY 5x2Disconnect1 plug for NTC PCBABO-CENTER v/HENRIKSENS ELEKTRONIK6

13、.36.36.3ABO-CENTER v/HENRIKSENS ELEKTRONIKINSULATION TESTBeoLab 2 must be insulation tested if it has been dismantled.Make the test when the BeoLab 2 is reassembled and is ready to be returned to the customer.Insulation test at the Service centerShort-circuit the two pins of the mains plug and conne

14、ct them to one of the terminals of the Insulation tester. Connect the other terminal of the insulation tester to ground on the Power Link socket.To avoid damaging the BeoLab 2, it is essential to ensure that both terminals of the insulation tester have good contact.Slowly turn up the voltage control

15、 of the insulation tester until a voltage of 2.5kV(ac) is obtained.Maintain that voltage level for one second, then slowly turn it down again.During the testing the current must not exceed 10mA.Insulation test at the customerRemove the mains cable from the wall outlet.Place a jumper across the two A

16、C plug prongs.Use a multi-meter, set for measurements in the Ohm-area.Place one lead from the multi-meter on the AC plug and place the other lead on ground at the Power Link plug.The resistance during this measurement must be of 1 Mega Ohm or more.Resistance measured below 1 Mega Ohm indicates an ab

17、normal situation and corrective action must be taken.Please note:Avoid all skin contact with the AC plug and all other metal parts while performing the test, as this contact may infl uence the measurement.Insulation test, English 7.1ABO-CENTER v/HENRIKSENS ELEKTRONIKBang & OlufsenDK-7600 StruerDenmarkPhone +45 96 84 11 22*Fax +45 97 85 39 113538051 06-06ABO-CENTER v/HENRIKSENS ELEKTRONIK