HarmanKardon-AVR170_230-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR170_230-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR170_230-avr-sm维修电路原理图.pdf（114页珍藏版）》请在收音机爱好者资料库上搜索。

1、Harman Kardon Service Manual AVR 170/230 2x100W/2 channels 5.1 CHANNEL A/V RECEIVER Released EU2012 Harman Consumer Group, Inc. Rev 1, 12/2012 8500 Balboa Boulevard Northridge, California 91329 CONTENTS BIAS ADJUSTMENT 87 PCB DRAWINGS 88 BLOCK DIAGRAMS 100 WIRING DIAGRAM 102 SCHEMATIC DIAGRAMS 103 E

2、SD WARNING 2 OWNERS MANUAL 3 PACKAGE DRAWING 50 DISASSEMBLY 51 EXPLODED VIEW AND PARTS 52 PARTS LIST 53 RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a com

3、ponent identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated fr

4、om the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field e

5、ffect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge o

6、nyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, pl

7、ace the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified

8、as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to i

9、nstall it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechas

10、sis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your

11、clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION : Harman KardonAVR 170 / 230V Service ManualPage 2 of 114RadioFans.CN 收音机爱 好者资料库Audio/video receiverAVR 1700, AVR 170, AVR 170/230COwners ManualHarman KardonAVR

12、 170 / 230V Service ManualPage 3 of 114AVR2Table of ContentsIntroductIon 3SupplIed AcceSSorIeS 3ImportAnt SAfety InformAtIon 3plAce the AVr 3front-pAnel controlS 4reAr-pAnel connectorS 6SyStem remote control functIonS 8IntroductIon to home theAter 10typIcAl home theAter SyStem 10multIchAnnel AudIo 1

13、0Surround modeS 10plAce your SpeAkerS 10plAcIng the left, center And rIght SpeAkerS 10plAcIng the Surround SpeAkerS 10plAcIng the Subwoofer 10typeS of home theAter SyStem connectIonS 11SpeAker connectIonS 11Subwoofer connectIonS 11Source deVIce connectIonS 11VIdeo connectIonS 12rAdIo connectIonS 12u

14、Sb/ipod port 12mAkIng connectIonS 13connect your SpeAkerS 13connect your Subwoofer 13connect your tV or VIdeo dISplAy 13connect your AudIo And VIdeo Source deVIceS 13connect to your home network 15connect the rAdIo AntennAS 15connect Ir equIpment 15connect the trIgger output 15connect to Ac power 16

15、Set up the remote control 16InStAll the bAtterIeS In the remote control 16progrAm the remote to control your Source deVIceS And tV 16Set up the AVr 17turn on the AVr 17uSIng the on-Screen menu SyStem 17confIgure the AVr for your SpeAkerS 17ASSIgn the AVr Input connectorS 18Set up the network 18AddIt

16、IonAl Source Setup menu ItemS 19operAtIng your AVr 19controllIng the Volume 19mutIng the Sound 19lIStenIng through heAdphoneS 19SelectIng A Source 19VIdeo troubleShootIng tIpS 19lIStenIng to fm And Am rAdIo 20lIStenIng to Internet rAdIo (vtuner) 20lIStenIng to An ipod/iphone/ipad deVIce 20lIStenIng

17、to medIA on A uSb deVIce 20lIStenIng to medIA VIA your home network 21lIStenIng to medIA VIA AIrplAy 22SelectIng A Surround mode 22AdVAnced functIonS 23AudIo proceSSIng And Surround Sound 23mAnuAl SpeAker Setup 24SyStem Setup 26AdVAnced remote control progrAmmIng 26recordIng 27Sleep tImer 27reSettIn

18、g the remote 27proceSSor reSet 27memory 27troubleShootIng 28SpecIfIcAtIonS 29AppendIx 30Harman KardonAVR 170 / 230V Service ManualPage 4 of 114AVR3EnglishIntroduction, Supplied Accessories, Important Safety Information and Place the AVRIntroductionThank you for choosing this Harman Kardon product! f

19、or more than fifty years, the harman kardon mission has been to share a passion for music and entertainment, using leading-edge technology to achieve premium performance. Sidney harman and bernard kardon invented the receiver, a single component designed to simplify home entertainment without compro

20、mising performance. over the years, harman kardon products have become easier to use while offering more features and sounding better than ever.the AVr 1700, AVr 170 and AVr 170/230c 5.1-channel digital audio/video receivers (AVrs) continue this tradition with some of the most advanced audio and vid

21、eo processing capabilities yet and a wealth of listening and viewing options.to obtain the maximum enjoyment from your new AVr, please read this manual and refer back to it as you become more familiar with its features and their operation.If you have any questions about this product, its installatio

22、n or its operation, please contact your harman kardon retailer or custom installer, or visit our web site at .Supplied Accessoriesthe following accessory items are supplied with your AVr. If any of these items are missing, please contact your harman kardon dealer, or harman kardon customer service a

23、t . System remote control EzSet/EQ microphone AM loop antenna FM wire antenna Three AAA batteries AC power cordIMPORTANT SAFETY INFORMATIONVerify Line Voltage Before Usethe AVr 1700 has been designed for use with 120-volt alternating current (Ac). the AVr 170 and AVr 170/230c have has been designed

24、for use with 220 240-volt Ac. connection to a line voltage other than that for which your AVr is intended can create a safety and fire hazard, and may damage the unit. If you have any questions about the voltage requirements for your specific model or about the line voltage in your area, contact you

25、r selling dealer before plugging the unit into a wall outlet.Do Not Use Extension CordsTo avoid safety hazards, use only the power cord supplied with your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or ca

26、rpets, or place heavy objects on them. damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.Handle the AC Power Cord Gentlywhen disconnecting the power cord from an Ac outlet, always pull the plug; never pull the cord. If you d

27、o not intend to use your AVr for any considerable length of time, disconnect the plug from the Ac outlet.Do Not Open the Cabinetthere are no user-serviceable components inside this product. opening the cabinet may present a shock hazard, and any modification to the product will void your warranty. I

28、f water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.CATV or Antenna Grounding (AVR 1700)If an outside antenna or cable system is connected to this product, be

29、 certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the united States national electrical code, AnSI/nfpA no. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead

30、-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode.NOTE TO CATV SYSTEM INSTALLER: this reminder is provided to call the cAtV (cable tV) system installers attention to

31、article 820-40 of the nec, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.Place the AVR Place the AVR on a firm and level surface. Be certa

32、in that the surface and any mounting hardware can support the AVrs weight. Provide proper space above and below the AVR for ventilation. Recommended clearance distances are 30cm above the unit, 30cm behind the unit and 30cm on each side of the unit. If you install the AVR in a cabinet or other enclo

33、sed area, provide cooling air within the cabinet. under some circumstances, a fan may be required. Do not obstruct the ventilation slots on the top of the AVR or place objects directly over them. Do not place the AVR directly on a carpeted surface. Do not place the AVR in moist or humid locations, i

34、n extremely hot or cold locations, in areas near heaters or heat registers, or in direct sunlight.Harman KardonAVR 170 / 230V Service ManualPage 5 of 114AVR4Front-Panel ControlsFront-Panel Controlspower Indicator/ power buttonmessage displayVolume knobSurround mode Select buttonsSet buttonIr Sensorc

35、hannel level control buttonSource Select buttonsleft/right buttonsheadphone Jack/ EzSet/EQ Mic connectortuning mode button/ rdS buttondigital Input buttonSurround-mode category buttonup/down buttons/ tuning buttonsuSb portAux Analog Audio Input connectorHarman KardonAVR 170 / 230V Service ManualPage

36、 6 of 114AVR5EnglishFront-Panel Controls, continuedFront-Panel Controls, continuedPower indicator/Power button: the AVr has four different power modes: Off (Power indicator not illuminated): when the rear-panel main power switch is in the off position or the power cord is unplugged the AVr is off an

37、d will not respond to any commands. plugging the power cord into a live Ac outlet and setting the main power switch in the on position will put the AVr into the eco Standby mode. Eco Standby (Power indicator glows solid amber): The Eco Standby mode minimizes energy consumption when youre not using t

38、he AVr. when the AVr is in eco Standby, it will not automatically turn on or play audio in response to an Airplay signal from a networked device. when the AVr is in eco Standby, pressing the power button turns it on. to put the AVr into eco Standby when it is on, press the power button for more than

39、 three seconds. NOTE: The AVR will not automatically enter the Eco Standby mode. Standby (Power indicator glows solid amber): the Standby mode mutes the AVr and shuts off its front-panel display, but allows the AVr to automatically turn on and play audio in response to an Airplay signal from a netwo

40、rked device. See Listening to Media via AirPlay, on page 22, for more information. when the AVr is in Standby, pressing the power button turns it on. to put the AVr into Standby when it is on, press the power button for less than three seconds. NOTE: The AVR will automatically enter the Standby mode

41、 whenever no control buttons have been pressed and no audio signal has been present for 30 minutes. On (Power indicator glows solid white): when the AVr is on it is fully operational.IMPORTANT NOTE: If the PROTECT message ever appears on the AVRs front-panel Message display, turn off the AVR and unp

42、lug it from the AC outlet. Check all speaker wires for a possible short circuit (the “+” and “” conductors touching each other or both touching the same piece of metal). If a short circuit is not found, bring the unit to an authorized Harman Kardon service center for inspection and repair before usi

43、ng it again.Tuning Mode button (AVR 1700 only): this button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an fm station is tuned in.RDS button (AVR 170 only): whe

44、n listening to an fm radio station that broadcasts rdS information, this button activates the various rdS functions. note: rdS service may not be available in all areas.Channel Level Control button: press this button to activate the channel-level adjustment feature. After pressing this button, use t

45、he up/down buttons to select the channel for adjustment and use the left/right buttons to adjust the channels level.Digital Input button: press this button to change the audio input for the current source. use the left/right buttons to cycle through the available input connections, and press the Set

46、 button to assign the currently-displayed connection to the source. IR sensor: this sensor receives infrared (Ir) commands from the remote control. It is important to ensure that the sensor is not blocked. Set button: press this button to select the currently highlighted menu item.Left/Right buttons

47、: use these buttons to navigate the AVrs menus.Message display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line.

48、 when the on-screen display menu system (oSd) is in use, the current menu settings appear.Up/Down buttons/Tuning buttons: use these buttons to navigate the AVrs menus. when the radio is the active source, use these buttons to tune stations according to the setting of the tuning mode button (see abov

49、e).Surround-Mode Category button: press this button to select a surround-sound category. each press changes the surround-mode category: Auto Select, Virtual, Stereo, movie, music and Video game. to change the specific surround-sound mode within the category, use the Surround mode Select buttons. See

50、 Audio Processing and Surround Sound, on page 23, for more information on surround modes.Surround-Mode Select buttons: After you have selected the desired surround-mode category, press these buttons to select a specific mode within the category, such as to change from dolby pro logic II movie mode t