HarmanKardon-AVR132_230-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR132_230-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR132_230-avr-sm维修电路原理图.pdf（67页珍藏版）》请在收音机爱好者资料库上搜索。

1、AVR 132/230 SERVICE MANUAL harman/kardon Power for the Digital Revolution RadioFans.CN 收音机爱 好者资料库TECHNICAL SPECIFICATIONS 35Technical SpecificationsAudio SectionStereo Mode Continuous Average Power (FTC)40 Watts per channel, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohmsFive-Channel Surround

2、 Modes Power Per Individual ChannelFront L&R channels:30 Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:30 Watts, 0.07% THD, 20Hz20kHz into 8 ohmsSurround channels:30 Watts per channel, 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/Impedance Linear (High Level)200mV/47kohmsSig

3、nal-to-Noise Ratio (IHF-A)95dBSurround System Adjacent Channel Separation Analog Decoding 40dB (Pro Logic, etc.) Dolby Digital (AC-3) 55dB DTS55dBFrequency Response 1W (+0dB, 3dB)10Hz100kHzHigh Instantaneous Current Capability (HCC)25 AmpsTransient Intermodulation Distortion (TIM)UnmeasurableRise Ti

4、me16secSlew Rate40V/secFM Tuner SectionFrequency Range87.5108MHzUsable SensitivityIHF 1.3 V/13.2dBfSignal-to-Noise RatioMono/Stereo: 70/65dB (DIN)DistortionMono/Stereo: 0.15/0.3%Stereo Separation35dB 1kHzSelectivity400kHz: 70dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequency Range 522162

5、0kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop: 500VDistortion1kHz, 50% Mod: 0.8%Selectivity10kHz: 30dBVideo SectionVideo FormatPAL/NTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance 1Vp-p/75 ohmsVideo Frequency Response10Hz8MHz (3dB)GeneralPower RequirementAC 220-240V/50HzPower Consu

6、mption72W idle, 580W maximum (2 channels driven)Dimensions (Max)Width440mm Height165mm Depth382mmWeight9.6 kgDepth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kar

7、don is a registered trademark.*Manufactured under license from Dolby Laboratories.“Dolby”,“Pro Logic”, and the Double-D symbol are trademarks of Dolby Laboratories, Inc.Confidential Unpublished Works. 19921999 Dolby Laboratories, Inc.All rights reserved.DTS and DTS Neo:6 are registered trademarks of

8、 DTS, Inc. 96/24 is a trademark of DTS, Inc.Logic 7 is a registered trademark of Lexicon, Inc.29782_AVR132_ENG_sort 10/08/06 16:45 Side 35RadioFans.CN 收音机爱 好者资料库SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURREN

9、T CHECKMeasure leakage current to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance

10、 directly into a 120V AC 60Hz outlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexpo

11、sed metalsurfacesAlso test withplug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundFRONT PANEL CONTROLS 5?Main Power Switch: Press this button toapply power to the AVR.When the switch ispressed in, the unit is placed in a Standb

12、ymode, as indicated by the orange LED 2.Thisbutton MUST be pressed in to operate the unit.To turn the unit off completely and prevent theuse of the remote control, this switch should bepressed until it pops out from the front panelso that the word “OFF” may be read at the topof the switch.NOTE:This

13、switch is normally left in the “ON”position.1System Power Control:When the MainPower Switch?is “ON,” press this button toturn on the AVR; press it again to turn the unitoff (to Standby). Note that the PowerIndicator2will turn blue when the unit is on.2Power Indicator:This LED will be illumi-nated in

14、 orange when the unit is in the Standbymode to signal that the unit is ready to beturned on.When the unit is in operation, theindicator will turn blue.3Headphone Jack:This jack may be used tolisten to the AVRs output through a pair ofheadphones. Be certain that the headphoneshave a standard 6.3 mm s

15、tereo phone plug.Note that the speakers will automatically beturned off when the headphones are connected.4Digital Optical 3 Input: Connect the opti-cal digital audio output of an audio or video prod-uct to this jack.When the Input is not in use,becertain to keep the plastic cap installed to avoiddu

16、st contamination that might degrade future performance.5Speaker/Channel Input Indicators:Theseindicators are multipurpose,indicating either thespeaker type selected for each channel or theincoming data-signal configuration.The left,cen-ter,right,right surround and left surround speakerindicators are

17、 composed of three boxes,while thesubwoofer is a single box.The center box lightswhen a “Small”speaker is selected,and the twoouter boxes light when “Large”speakers areselected.When none of the boxes are lit for thecenter,surround or subwoofer channels,nospeaker has been selected for that position.(

18、Seepage 16 for more information on configuringspeakers.) The letters inside each of the centerboxes display active input channels.For standardanalog inputs,only the L and R will light,indicat-ing a stereo input.When a digital source is play-ing,the indicators will light to display the chan-nels begi

19、n received at the digital input.When theletters flash,the digital input has been interrupt-ed.(See page 20 for more information on theChannel Indicators).Front Panel Controls?123 4 56 7 8 9A B C D E F G H I J Main Power SwitchSystem Power ControlPower IndicatorHeadphone JackDigital Optical 3 InputSp

20、eaker/Channel Input IndicatorSurround Mode Group SelectorTuningTuner Band SelectorPreset Stations SelectorInput Source SelectorRDS Select ButtonSurround Mode SelectorSurround Mode IndicatorsRemote Sensor WindowMain Information DisplayDigital Coax 3 InputVideo 3 input jacksVolume ControlInput Indicat

21、ors167G9DFIJC8BL24A5E3DIGITALLOGIC 7VID 1DVDCDFMAMTAPEVID 2VID 3PRO LOGIC 3 STEREO DSP5 CH. STEREOSURR. OFF6 CH29782_AVR132_ENG_sort 10/08/06 16:45 Side 56 FRONT PANEL CONTROLSFront Panel Controls6Surround Mode Group Selector: Pressthis button to select the top-level group ofsurround modes. Each pre

22、ss of the button willselect a major mode grouping in the followingorder:Dolby Modes DTS Digital Modes DSPModes Stereo Modes Logic 7 ModesOnce the button is pressed so that the name ofthe desired surround mode group appears in theLower Display LineF, press the SurroundMode SelectorCto cycle through t

23、he indi-vidual modes available. For example, press thisbutton to select Dolby modes, and then pressthe Surround Mode SelectorCto choosefrom the various mode options.7Tuning Selector: Press the left side of thebutton to tune lower frequency stations and theright side of the button to tune higher freq

24、uencystations.When a station with a strong signal isreached,MANUAL TUNEDor AUTOTUNEDwill appear in the Main InformationDisplay F(see page 27 for more informationon tuning stations).8Tuner Band Selector: Pressing this buttonwill automatically switch the AVR to the Tunermode. Pressing it again will sw

25、itch between theAM and FM frequency bands, holding it pressedfor some seconds will switch between stereoand mono receiving and between automatic andmanual tuning mode (See page 27 for moreinformation on the tuner).9Preset Stations Selector: Press thisbutton to scroll up or down through the list ofst

26、ations that have been entered into the presetmemory. (See page 27 for more information ontuner programming.)AInput Source Selector: Press this buttonto change the input by scrolling through the listof input sources.BRDS Select Button: Press this button todisplay the various messages that are part of

27、 theRDS data system of the AVRs tuner.(See page 28for more information on RDS).CSurround Mode Selector: Press this but-ton to select from among the available surroundmode options for the mode group selected.Thespecific modes will vary based on the number ofspeakers available, the mode group and if t

28、heinput source is digital or analog. For example,press the Surround Mode Group Selector6to select a mode grouping such as Dolby orLogic 7, and then press this button to see themode choices available. For more information onmode selection, see page 21.DSurround Mode Indicators: Indicator willillumina

29、te in front of the surround mode that iscurrently in use.ERemote Sensor Window:The sensorbehind this window receives infrared signalsfrom the remote control.Aim the remote at thisarea and do not block or cover it unless anexternal remote sensor is installed.FMain Information Display:This displaydeli

30、vers messages and status indications to helpyou operate the receiver.GDigital Coax 3 Input:This jack is normallyused for connection to the output of portabledigital audio devices, video game consoles orother products that have a coax digital jack.HVideo 3 Input Jacks: These audio/videojacks may be u

31、sed for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio players.IVolume Control:Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR is muted,adjusting volume control will automaticallyrelease the

32、unit from the silenced condition.JInput indicators: Indicator will illuminatein front of the input that is currently being usedas the source for the AVR.29782_AVR132_ENG_sort 10/08/06 16:45 Side 6REAR PANEL CONNECTIONS 7Rear Panel Connectionsc?fideb fla?Tape InputsTape OutputsVideo 1 Audio InputsAM

33、AntennaVideo 1 Audio OutputsDVD Audio InputsFM AntennaCD InputsVideo 2 Component Video InputsCoaxial Digital InputsSubwoofer OutputVideo Monitor OutputsFront/Center Speaker OutputsSurround Speaker OutputsComponent Video OutputsVideo 1 Component Video InputsAC Power CordDVD Video InputsVideo 1 Video

34、OutputsVideo 2 Audio InputsVideo 2 Video InputsOptical Digital InputsVideo 1 Video Inputs6-Channel Direct Inputs ?Tape Inputs: Connect these jacks to thePLAY/OUT jacks of an audio recorder.?Tape Outputs: Connect these jacks to theRECORD/INPUT jacks of an audio recorder.?Video 1 Audio Inputs: Connect

35、 these jacksto the PLAY/OUT audio jacks on a VCR or othervideo source.?AMAntenna:ConnecttheAMloopantennasuppliedwiththereceivertotheseterminals.IfanexternalAMantennaisused,makeconnections tothe AM and GND terminals in accordance withthe instructions supplied with the antenna.?Video 1 Audio Outputs:

36、Connect thesejacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.?DVD Audio Inputs: Connect these jacks tothe analog audio jacks on a DVD or other videosource.?FM Antenna: Connect the supplied indoor oran optional external FM antenna to this terminal.?CD Inputs: Connect these

37、jacks to the ana-log output of a compact disc player or CDchanger.?Video 2 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofan HDTV Set-top convertor, satellite receiver, orother video source device with component videooutputs to these jacks.?Coaxial Digital Inputs: Connect the c

38、oaxdigital output from a DVD player,HDTV receiver,LD player,MD player or CD player to these jacks.The signal may be either a Dolby Digital signal,DTS signal or a standard PCM digital source.Donot connect the RF digital output of an LD play-er to these jacks.?Subwoofer Output: Connect this jack tothe

39、 line-level input of a powered subwoofer. Ifan external subwoofer amplifier is used, connectthis jack to the subwoofer amplifier input.29782_AVR132_ENG_sort 10/08/06 16:45 Side 78 REAR PANEL CONNECTIONSRear Panel Connections?Video Monitor Outputs: Connect thesejacks to the composite and/or S-Video i

40、nput of aTV monitor or video projector to view the outputof any video source selected by the receiversvideo switcher.?Front/Center Speaker Outputs: Connectthese outputs to the matching + or terminalson your front/center speakers.When makingspeaker connections, always make certain tomaintain correct

41、polarity by connecting the red(+) terminals on the AVR to the red (+) terminalson the speaker and the black () terminals onthe AVR to the black () terminals on the speak-ers. (See page 12 for more information onspeaker polarity.)?Surround Speaker Outputs: Connectthese outputs to the matching + or te

42、rminalson your left and right surround speakers.Whenmaking speaker connections always make cer-tain to maintain correct polarity by connectingthe red (+) terminals on the AVR to the red (+)terminals on the speakers and the black () ter-minals on the AVR to the black () terminals onthe speakers. See

43、page 12 for more informationon speaker polarity.?Monitor Component Video Outputs:Connect these outputs to the component videoinputs of a video projector or monitor.When asource connected to one of the twoComponent Video Inputs?is selectedthe signal will be sent to these jacks.?Video 1 Component Vide

44、o Inputs:Connect the Y/Pr/Pb component video outputs ofa DVD player to these jacks.Note: All component inputs/outputs can beused for RGB signals too, in the same way asdescribed for the Y/Pr/Pb signals, then connectedto the jacks with the corresponding color.RGB connection is not possible if the sou

45、rce out-puts a separate sync signal (see page 13).?AC Power Cord: Connect the AC plug to anunswitched AC wall output.?DVD Video Inputs: Connect these jacks tothe composite or S-Video output jacks on a DVDplayer or other video source.?Video 1 Video Outputs: Connect thesejacks to the RECORD/INPUT comp

46、osite or S-Video jack on a VCR.?Video 2 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a VCR or othervideo source.?Video 2 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona second VCR or other video source.?Optical Digital Inputs: Connect the opticaldig

47、ital output from a DVD player, HDTV receiver,LD player,MD player or CD player to these jacks.The signal may be either a Dolby Digital signal, aDTS signal or a standard PCM digital source.?Video 1 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona VCR or other video sourc

48、e.Note: Either the Video or S-Video output of anyS-Video source must be connected to the AVR, not both in parallel, otherwise the videomay be disturbed or its performance beadversely effected.?6-Channel Direct Inputs:These jacks areused for connection to source devices such asDVD-Audio or SACD playe

49、rs with discrete analogoutputs.29782_AVR132_ENG_sort 10/08/06 16:45 Side 8Surround Mode ChartMODEFEATURESDELAY TIME RANGEDOLBY DIGITALAvailable only with digital input sources encoded with Dolby Digital data. It provides Center: 0 ms 5 msup to five separate main audio channels and a special dedicate

50、d Low Frequency Effects Initial Setting 0 mschannel.Surround: 0 ms 15 msInitial Setting 0 msDTS 5.1When the speaker configuration is set for 5.1-channel operation, the DTS 5.1 mode is available when DVD, audio-only music or laserdiscs encoded with DTS data are played.DTS 5.1 provides up to five sepa