Bogen-BPA125-pwr-sch维修电路原理图.pdf

《Bogen-BPA125-pwr-sch维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Bogen-BPA125-pwr-sch维修电路原理图.pdf（7页珍藏版）》请在收音机爱好者资料库上搜索。

1、RadioFans.CN 收音机爱 好者资料库TECHNICAL SPECIFICATIONSRated Output Power:Model BPA-6060 watts (rms) from 50Hz toI5kHz at less than 2%THDinto rated load impedancesModel BPA- 125125 watts (rms) from 5OHz to15kHz at less than 2% THDinto rated load impedancesFrequency Response:Input Sensitivity:Output Regulati

2、on:-2dB from 20Hz to 2OkHzHigh-impedance: 300mV;Low-impedance, balanced: 75mV with accessory transformer Model TL600Better than 2dB from no load to full loadHum and Noise:Inputs (Impedance):85dB below rated outputHigh-impedance: 50k-ohms unbalanced;Low-impedance: 600-ohms balanced, with accessory tr

3、ansformer TL600;Line-bridging with accessory transformers TLl00 or TLlOKOutput Loads:8-ohm/25V, 16-ohms,4-ohm/25V, 16-ohms,25VCT and 70V 25VCT and 70VLo-Cut Filter:Controls, Indicators;Front Panel:Rear Panel:Power Consumption;I20VAC, 60Hz Full Rated Output:-1OdB 1OOHz (Switch-Selectable)Illuminated

4、Power SwitchInput Level Control; Circuit Breaker Reset Switch; Lo-Cut Filter Switch18OW 360wOverload Protection:I1AC Circuit Breaker. Thermal Circuit Breaker, Transient Protection Diodes1Auxiliary Receptacle:(not switched)Dimensions:Three-wire grounded* 300 watts maximum15.25”Wx8”Dx3.5”H15.25”Wx8”Dx

5、5.25”H(38.7 x 20.3 x 8.9 cm) (38.7 x 20.3 x 13.3 cm)Finish:I BlackWeight:Rack Panel Brackets:19 lbs. (8.6 kg)RPK-5327 Ibs. (12.3 kg)RPK-54Accessories: Model TL600, 600-ohm line-matching transformerModel TLIOO, 1:1 ratio transformerModel TLlOK, 10,000-ohm line-matching transformer*This receptacle wil

6、l be grounded only if the power amplifier has been grounded properlyAll specifications subject to change without noticeAMPLIFIER 1G N D COM 25VCTAMPLIFIER 2GND COM 25VCTAMPLIFIER I AMPLIFIER 2G N D C O M l6fi G N D C O M lGfIIA74-2021-01OUTPUTTERMINALsz&RoFAMPLIFIERIMPEDANCEINPUT OFPOWERAMPLIFIERA T

7、 7OV R I = 10K, 1/2WA T 2 5 V R I = 3.3K, 1/2W-0730-AFigure 1 - Connecting Amplifiers in Series Figure 2 - Input From Another Amplifier2RadioFans.CN 收音机爱 好者资料库Figure 3 - BPA-60 Rear Panel Connection DiagramCONNECTING AMPLIFIERS IN SERIES. Pairs of the sameamplifier model may be connected in series t

8、o effectively dou-ble the power output into the same load line (see Figure 1). Becertain to remove the link between COM and GND terminalson amplifier No. 2.BRIDGING INPUT. The inputs of two or more amplifiers maybe paralleled by installing accessory transformer TLlOO (for upto 6 amplifiers) or TLlOK

9、 (for more than 6 amplifiers) in thetransformer socket designated XT-l (see Figure 5) on theprinted circuit board. Connect the signal source to the BALLO-Z terminal strip and connect the cable shield to the GNDterminal. For an unbalanced input, connect a jumper wire fromthe GND terminal to an adjace

10、nt input terminal.INPUT FROM ANOTHER AMPLIFIER. The BPA-60 andBPA-125 amplifiers may be driven from an amplifier that pro-vides a 25-volt or 70-volt constant voltage output. Connect theoutput of the driver amplifier to one of the HI-Z input jacks viaa resistor network (see Figure 2). These resistors

11、 are in additionto the normal loudspeaker load impedance on the output of thedriver amplifier.OUTPUT CONNECTIONSCAUTIONFollow local electrical codes when connecting ampljieroutput.Fires 3 and 4 show the location and impedance values for theoutput terminal strip. Class 2 wiring is acceptable for outp

12、ut loads.SPEAKERS. The amplifier may be used with most conventionalspeaker systems. For detailed information on the installation ofmultiple speaker systems, refer to the Speaker Installation Bulletin(No. 54-5001) included with this unit.Connect speaker systems directly to the output terminal strip o

13、nthe rear panel. Connect one speaker lead to the COM terminal andthe other to the terminal corresponding to the impedance of thespeaker system. If the load impedance falls between two output ter-minal values, use the terminal of lower impedance. Total powerdistribution to the speakers should not be

14、greater than the powerrating of the amplifier. For balanced output lines, remove the linkbetween the COM and GND terminals. If the line is shielded, con-nect the shield to the GND terminal. For unbalanced speaker lines,close the link between the COM and GND terminals.HUM. If the connections between

15、the signal sources and amplifierare incorrect or defective, hum-type interference may occur. Checkfor proper grounding, broken wires, shields, poor connector con-tacts, etc. Keep input cables away from speaker cables and speakercables away from AC power lines. Where a turntable or other aux-iliary e

16、quipment is used, it may be necessary to connect a separateground wire from the chassis of such equipment to a suitable earthground.POWER. The POWER switch applies power to the amplifier; itdoes not control any associated equipment which may be connectedto the auxiliary power receptacle on the rear

17、panel. The switch lampwill illuminate when power has been applied to the unit.LO-CUT FILTER SWITCH. The LO-CUT filter switch, located onthe rear panel, provides -1OdB attenuation at 100Hz.INPUT LEVEL CONTROL. The INPUT LEVEL control, locatedon the rear panel, adjusts the input signal applied to the

18、amplifier.Turn the adjustable screw clockwise to increase the level.CAUTIONMany loudspeakers may be damaged if overdriven.Therefore, always begin system setup with the inputlevel control fully counterclockwise and gradually in-crease the setting to obtain the desired output level.4Figure 4 - BPA-125

19、 Rear Panel Connection DiagramTHERMAL BREAKER. If the thermal breaker opens, there will beno audio output; however, the power switch lamp will remain illu-minated. Wait approximately two minutes for the breaker to reset. Ifit resets and then opens again, investigate the cause of thetemperature overl

20、oad. This may be due to improper connections atthe output terminals or to excessive environmental heat with inade-quate ventilation. The thermal breaker will open when thetemperature at the output transistor heat sink reaches 105 C.CIRCUlT BREAKER. .If the AC circuit breaker opens, the powerswitch l

21、amp wiIl go out and the amplifier will have no output;however, there will be power at the AUX POWER receptacle on therear panel. Set the POWER switch to OFF and momentarily depressthe red button on the circuit breaker to reset it. Return the POWERswitch to ON. If the circuit breaker trips again, do

22、not attempt toreset it; have the trouble investigated by a qualified technician.MAINTENANCECAUTIONThere are no user-serviceable parts within theamplifier. Have all internal servicing performed by aqualifed technician. The warranty will become void ifrepairs are made by other than the Bogen ServiceDe

23、partment or authorized service agency.BOGEN SERVICEOur Service Department is interested in the maintenance ofyour Bogen equipment. If trouble ever develops, do not hesitateto ask our advice or assistance. Information may be obtained bywriting to: Service Department, Bogen Division, P.O. Box 500,Para

24、mus, N.J. 07653.When communicating with us, give the model and seriesdesignation of your unit. Describe the difficulty and includedetails on the electrical connections to associated equipment,such as preamplifiers, speakers, etc. We will send you service in-formation if the trouble appears simple. I

25、f the amplifier requiresservicing, we will send you the name and address of the nearestauthorized Bogen service agency.When shipping the amplifier, pack it well, using the originalshipping carton or similar container and filler material to preventdamage in transit. Remove any plug-in transformer fro

26、m theprinted circuit board beforeshipping. Send the unit, fully insuredand freight prepaid via UPS or other responsible carrier. Therepaired unit may be picked up by you personally or will bereturned to you freight prepaid while in warranty.REPLACING COMPONENTSAll semiconductor components on the pri

27、nted circuit boardare soldered in place to ensure maximum reliability. Whensoldering or unsoldering transistors and diodes, use a heat sink(such as a small alligator clip) between the source of heat and thecomponent. When replacing driver and output transistors, becertain to install the case/heat si

28、nk insulator, after lightly coatingboth sides with a thermal conducting compound (such as DowCorning No. 340, or equivalent).REPLACEMENT PARTSMost components used in the amplifier are standard partsavailable through reputable parts suppliers. The parts listed heremay be obtained through Bogen distri

29、butors, service agencies ordirectly from the factory. When ordering a part, specify the partnumber and the description, as listed. Specify the model of theunit and give the series designation, which is a letter followed bynumbers, located on the rear panel. For parts on the circuitboard, also give t

30、he component board assembly number, whichbegins with “45”.TRANS. SKT. XT1I0Figure 5 - BPA-60/BPA-125 Printed Circuit BoardPARTS LISTDesignation-c2C3,4C6CR1-4:;:RlR3R4R5Rl8,19Sl-Cl01Cl03Cl04C201C202PartNumber DescriptionPC Board45-7241-05 Ptd. Cir. Bd. Assy.79-l 19-001 Cap., Elect., 470 F, 63V79-008-

31、065 Cap., Elect., 10 F, 63V79-008-062 Cap., Elect., 100 F, 50V96-5333-01 Diode, 4OOprv 1A96-5643-01 Transistor, KTC224096-5365-01 Transistor, MPSA5696-5459-01 Transistor, 2N629296-5458-01 Transistor, 2N610777-001-818 Control, Scr. Adj., 100 kilohm75-154-124 Resistor, 120 kilohm, W , 1%75-154-154 Res

32、istor, 150 kilohm, 1/4W, 1%75-154-334 Resistor, 330 kilohm, 1/4W, 1%76- 107-096 Resistor, .82 ohm, 2W81-003-067 Switch, Slide, Miniature70-9302-01 Clip, Heat Sink (2)Chassis78-200-l 1679- 118-002Cap., Cer. Disc, 0.01 F, 1400VCap., Elect., 13,000 F, 40V(BPA-125)79-118-004 Cap., Elect., 8800 F, 75V(BP

33、A-125)79-118-006 Cap., Elect., 5000 F , 50V(BPA-60)79-509-056 Cap., Elect., 6000 F , 75V(BPA-60)SchematicDesignationPartNumberCBlOl 94-0023-10CB102 94-0014-07CB201 94-0023-05CR101 96-5373-01CR201 -204 96-5241-01QlOl 96-5213-014102,103 96-5385-01Q104-107 96-5385-01R101,102R103-10676-114-10776-l 14-10

34、2R107 75-154-182R109R201,20375-742-10176-l 14-102R202 75-154-132SW101 81-009-036TlOl 83-831-000T102 83-492-000T201 83-814-000T202 83-491-000-14-9088-016DescriptionBreaker, Circuit, 4.OA(BPA-125)ThermostatBreaker, Circuit, 1.6A (BPA-60)Rectifier, Bridge (BPA-125)Diode, 300prv 3A (BPA-60)Transistor, 2

35、N5089Transistor, 2N3055H, RCATransistor, 2N3055H, RCA(BPA-125)Resistor, 3.3 ohm, 5W(BPA-125)Resistor, 0.27 ohm, 5W(BPA-125)Resistor, 1800 ohm, 1/4W, 1%(BPA-125)Resistor, 100 ohm, 7WResistor, 0.27 ohm, 5W(BPA-60)Resistor, 1300 ohm, 1/4W, 1%(BPA-60)Switch, PowerTransformer, Power (BPA-125)Transformer, Output (BPA-125) Transformer, Power (BPA-60)Transformer, Output (BPA-60)Foot, Rubber