Classe-CAM350-pwr-sm维修电路原理图.pdf

《Classe-CAM350-pwr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Classe-CAM350-pwr-sm维修电路原理图.pdf（23页珍藏版）》请在收音机爱好者资料库上搜索。

1、PRO-SVR_LEGACY Page 1 of 13 Date:August 16, 2007 Model Number: CAM-350Class Audio Inc.Subject:Service manual Class Audio, Inc. 5070 Franois Cusson Lachine, Qubec Canada H8T1B3, RadioFans.CN 收音机爱 好者资料库PRO-SVR_LEGACY Page 2 of 13 Table of ContentsIntroduction 3Important Notes on Servicing 3Ordering Re

2、placement Parts 3Block Diagrams 4Start up Procedure 5Protection Modes and Indicators 6Troubleshooting Guide 7Output Transistors Testing and Replacement 8Calibrations and Adjustments 9Parts List 10Updates 11Fuses 12Voltage Change 12IR Interface Information 13Schematics 14The contents of this document

3、 as well as the files associated with it contain confidential information that is proprietary to Class Audio Incorporated and are intended solely for the purpose of servicing product. No part of its contents may be used, copied, disclosed, or conveyed to any party in any manner whatsoever without pr

4、ior written permission from Class Audio Incorporated. RadioFans.CN 收音机爱 好者资料库PRO-SVR_LEGACY Page 3 of 13 IntroductionPlease read this manual carefully before commencing servicing! Only qualified and authorized personnel should attempt to service this product. The lightning flash with arrowhead symbo

5、l, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to a

6、lert the user to the presence of important operating and maintenance (servicing) instructions. Class has a global product support network. For product assistance or to order replacement parts please contact your nearest service center always quoting the unit serial number. North America Phone: (978)

7、 664-2870 E-mail: EuropePhone: 44 (0) 1903 221 700 E-mail: AsiaPhone: (852) 2790 8903 E-mail: classebwgroup.hkRest of the World Phone: (514) 636-6384 E-mail: Important Notes on Servicing 1.ALWAYS observe ESD precautions when handling electronic modules or PCBAs. 2.NEVER exchange boards with a differ

8、ent revision number, unless authorized by Class. 3.ALWAYS use Class original replacement parts. The use of generic parts may void the warranty of the unit. Ordering Replacement Parts There may be a delay in processing incomplete requests. Please be sure to include all required information. Remember

9、to quote the serial number of the unit on all replacement part orders and the Class order number when returning defective parts for credit. PRO-SVR_LEGACY Page 4 of 13 Block diagramsPRO-SVR_LEGACY Page 5 of 13 Start Up ProcedureWhen receiving a unit, an assiduous visual inspection must be performed.

10、 Do not connect the unit without analysing the symptoms reported by the customer and the results of the inspection. Using the troubleshooting guide, find the problem and proceed to the repair. Once this step is done, follow these steps, known as the start-up procedure, to ensure that everything in t

11、he unit is in working condition. 1. Proceed with a post repair visual inspection. Take the time to check if every wire is reconnected properly, every screw is bolted on, no soldering and/or metal residues lying in the unit, every fuse has been replaced, etc. 2. Connect the unit to a variable transfo

12、rmer, setted to 0Vac. 3. Turn the bias trimpot (RV1) counter clockwise until a click is heard. 4. Connect the bypass wire to the variable transformer. This bypass is a power cord, modified on the female side in order to bypass the soft start sequence. It is connected to the line tab on voltage selec

13、tor PCB. 5. Slowly raise the voltage to 10Vac, and check positive and negative rails and pre-driver supply. Check fuses.6. If one or more supply are not within specifications, return to the troubleshooting guide. 7. Slowly raise voltage until you hear relays click, this point is around 55Vac. Rechec

14、k every supply. 8. If one or more supply are not within specifications, return to the troubleshooting guide. 9. Raise voltage to 120Vac. Recheck every supply 10. If every supply is within specifications, unplug the unit and bypass from the variable transformer. Reconnect only the unit. 11. Report to

15、 calibration and adjusments to adjust bias and DC offset. Note that bias can be adjusted to 14mV, and the following tests can be performed before the unit is send to the burn-in bench for a 24 hours warm-up. 12. Connect the unit to a load, and to a source using balanced inputs and single ended input

16、s, independently. 13. Perform a test with a 200Hz, a 2kHz and a 20kHz tone, both sinus wave and square wave. Check the output with a oscilloscope, on 4 ohms and 8 ohms loads. Take special cares about oscillation and phase correlation between channels. 14. Connect the unit to a small speaker, and sho

17、rt the input. Check for any noise. Perform this step with single ended inputs and balanced inputs, independently. 15. Put the unit on a burn-in bench, and let it sit for 24 hours, then readjust bias. Let the unit on the burn-in bench for another 72 hours. 16. Redo steps 11 to 14 before shipping to t

18、he customer. PRO-SVR_LEGACY Page 6 of 13 Protection Modes and IndicatorsThe front LED shows the status of the amplifier. When starting up normally, the CAM350 will show a FLASHING RED LED for about 15 seconds and if all is normal, the LED will go SOLID RED. If there is a fault, the LED will go to a

19、FLASHING GREEN LED. The CAM350 is equipped with four Mosfet protection fuses. In the event that one or more of these fuses would blow, the technician will first need to identify and cure the cause of failure (please report to troubleshooting guide). When the cause has been identified, disconnect the

20、 unit from the system including the AC power. Remove the top cover and look for damaged or burned components. If no other components than the fuses appear to be damaged, the technician can then replace the broken fuses with the same value and rating (please report to fuses section). The Mosfet fuses

21、 are located on the control board. When replacing fuses, please make sure that the fuse holder are holding the fuses very tightly. A loose fuse holder can translate into distortion on top of the signal. PRO-SVR_LEGACY Page 7 of 13 Troubleshooting GuideSymptom Possible cause Unit won t turn on Check

22、connections; Check fuses; Check soft-start circuit; Check relays; Check power supply circuits (positive rail, negative rail, Mosfet supply). Smoked and/or burned components Check for short between components and ground; Check output transistors; Check output relays; Check power supply circuits (posi

23、tive rail, negative rail, Mosfet supply). Blown fuses Check for short between fuse and ground; Check power supply circuits (positive rail, negative rail, Mosfet supply). No output Check connexions; Check output relays; Check power supply circuits (positive rail, negative rail, Mosfet supply);Check o

24、utput transistors. Unit turn into protection Check for smoked and/or burned components; Check power supply circuits (positive rail, negative rail, Mosfet supply);Check source and load; Check protection circuit; Check sensor wires between sensor PCB and control PCB; Check outputs transistors and Mosf

25、et drivers. Excessive buzz and/or hum Check electrical lines; Check for a ground loop in the system. Oscillation Check source; Check capacitors on main board; Check 4.7? resistor. Intermittent signal Check connections; Replace shield wires. PRO-SVR_LEGACY Page 8 of 13 Output Transistors Testing and

26、ReplacementPLEASE NOTE THAT THESE TESTS ARE ONLY EFFECTIVE ON BIPOLAR TRANSISTORS. DO NOT PERFORM THESE TESTS ON MOSFET DEVICES, AS THEY ARE LIKELY TO BECOME SHORT DURING THE TEST.You should check all pin combinaisons, as there is a chance that only one side of the transistor is short. When replacin

27、g outputs transistors, the technician should first disconnect both outputs and main board to check if the blown outputs were caused by a faulty component on the amplifier s base. Blown output transistors should be replaced by kits, not individually. These kits contains matched transistors for both r

28、ails of one channel. When replacing blown output transistors, you must also replace positive and negative Mosfet drivers and bias transistor. Carefully inspect 4.7? resistor and 10? soft start resistor, and replace if necessary. Replace any burnt component or board. Pins : 1 Base 2 Collector 3 Emitt

29、er You should have these results, if the transistor is good. 2SC3264 (NPN) Positive lead Negative lead Result B C Conductive B E Conductive C B Infinite C E Infinite E B Infinite E C Infinite 2SA1295 (PNP) Positive lead Negative lead Result B C Infinite B E Infinite C B Conductive C E Infinite E B C

30、onductive E C Infinite PRO-SVR_LEGACY Page 9 of 13 Calibrations and AdjustmentsBias adjustment: Note: Bias adjustment should be made without any load connected to the amplifier s output, and no signal connected to the amplifier s input. 1. On positive heatsink, connect a multimeter to R111 leads and

31、 set the multimeter to mV scale. 2. Turn trimpot R104 counterclockwise until it reaches 0?. A click should be heard. 3. Turn on amplifier, and let it warm up for 15 minutes on idle. 4. Adjust trimpot R104 to get a 10mV reading. 5. Repeat procedure with negative heatsink. 6. Let the amplifier warm up

32、 for a 24 hours period with signal and load. 7. Remove signal and load, and reconnect the multimeter, setted to mV scale, to R112 leads. 8. Readjust R104 to get a 12mV reading. 9. Repeat procedure with negative heatsink. DC offset: Note: DC offset adjustment should be made without any load connected

33、 to the amplifier s output, and no signal connected to the amplifier s input. On these units, DC offset can t be adjusted. Measure DC offset using a voltmeter connected to the output posts, scale setted to mV. DC offset should be less than 10mV. PRO-SVR_LEGACY Page 10 of 13 Parts ListThis is not a d

34、etailed part list. It is a list of major chassis parts and PCBs. If you need to order a specific part, please contact Classe Audio with the part location, PCB number, and model and serial number of the unit. If you need a complete PCB, please replace the (x) in the Classe part number with the revisi

35、on number printed on the board. Parts Description Classe part number B1DAX Complete PCB, power switch B1DAXR(x) B1D1X Complete PCB, heatsink B1D1XR(x) B02AX Complete PCB, amplifier B02AXR(x) B1B3X Complete PCB, control B1B3XR(x) B1B1X Complete PCB, capacitors B1B1XR(x) B016X Complete PCB, AC B016XR(

36、x) B258X Complete PCB, input B258XR(x) B019X Complete PCB, sensor B019XR(x) B01GX Complete PCB, filter B01GXR(x) B1B2X Complete PCB, supply B1B2XR(x) PRO-SVR_LEGACY Page 11 of 13 Updates1. On board B1D1X (both PCBs), replace R104 with Classe part number 3299X-1-202. 2. On board B1D1X (both PCBs), re

37、place D101 and D103 with Classe part number 1N5333B. 3. On board B1B3X, replace P011XR02 to 040AR3, and drop rail voltage sensor from 500mV to 250mV. 4. Add a jumper from GND post on B1B1X PCB to relay GND on B1B3X PCB. PRO-SVR_LEGACY Page 12 of 13 FusesEXTRA PRECAUTIONS SHOULD BE TAKEN WHEN REPAIRI

38、NG, MODIFYING,ORTROUBLESHOOTING IN THE POWER SUPPLY AREA. UNIT MUST BE DISCONNECTFROM MAIN SOURCE AND CAPACITORS MUST BE DISCHARGED USING A 100W INCANDESCENT BULB. WHEN REPLACING FUSES, PLEASE MAKE SURE THAT THE FUSE HOLDERS ARE HOLDING THE FUSES VERY TIGHTLY. A LOOSE FUSE HOLDER CAN TRANSLATE INTO

39、DISTORTION ON TOP OF THE SIGNAL. Main fuses: For 100 120v units: 10A slo-blo, Classe part number MDA-10A For 220 240v units: 4A slo-blo, Classe part number MD The main fuse is located at the back of the unit, on the rear panel. Control board fuse: 0.50A, Classe part number 225.500 The control board

40、fuse is located on top of the supply board (B1B2X) Mosfet fuses: 0.75A, Classe part number 225.750 The Mosfet fuses are located on top of the supply board (B1B2X) Voltage ChangeEXTRA PRECAUTIONS SHOULD BE TAKEN WHEN REPAIRING, MODIFYING, ORTROUBLESHOOTING IN THE POWER SUPPLY AREA. UNIT MUST BE DISCO

41、NNECTFROM MAIN SOURCE AND CAPACITORS MUST BE DISCHARGED USING A 100W INCANDESCENT BULB. 1. Set the primary wires of the main transformer as described below. 2. Replace the varistor, according to new line voltage, following Classe s recommendations. If varistor is not available, remove old varistor a

42、nd leave it empty. 3. Set the jumpers accordingly on the auxiliary transformer located at the back of the unit on the top main board on the left-hand side of the auxiliary transformer (see tables below) Primary wires, main transformer Mains X1 X2 X3 X4 X5 X6 X7 X8 Varistor100VAC Grey YellowBlueBlack

43、Orange White - - 130 120VACBlueBlackGreyYellowOrange White - - 130 220VAC - YellowGreyBlack - White BlueOrange 250240VAC - Black GreyYellow- White BlueOrange 250Jumpers, auxiliary transformer Mains Position 1 Position 2 Position 3 Position 4 Position 5 100/120VAC In Out Out Out In 220/240VAC Out Out

44、 In Out Out PRO-SVR_LEGACY Page 13 of 13 IR Interface InformationPress and hold: AMP + LINE 1 = Turns on Amplifier # 1 AMP + LINE 2 = Turns on Amplifier # 2 AMP + LINE 3 = Turns on Amplifier # 3 AMP + BAL 1 = Turns on Amplifier # 4 AMP + BAL 2 = Turns on Amplifier # 5 AMP + BAL 3 = Turns on Amplifie

45、r # 6 J3 J2 J1 J0 ADDRESS RC Button Auto ON Note X X X X 0 Amp1 No QC setting X X X Out 1 Amp2 No X X Out X 2 Amp3 No X X Out Out 3 Amp4 No X Out X X 4 Amp5 No X Out X Out 5 Amp6 No X Out Out X 0 Amp1 No X Out Ot Out 0 Amp1 Yes On with AC Out X X X 0 DC No Out X X Out 1 DC No Out X Out X 2 DC No Out X Out Out 3 DC No Out Out X X 4 DC No Out Out X Out 5 DC No Out Out Out X 0 DC No Out Out Out Out 0 DC Yes On with AC B01GXR02.sch-1 - Tue Jul 17 11:41:29 2007B1DAXR01.sch-1 - Thu Jul 26 16:16:52 2007B258XR00.sch-1 - Thu Jul 26 16:15:00 2007