Denon-AVR2313CI-avr-sm维修电路原理图.pdf

《Denon-AVR2313CI-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR2313CI-avr-sm维修电路原理图.pdf（230页珍藏版）》请在收音机爱好者资料库上搜索。

1、D&M Holdings Inc.SERVICE MANUALeeMODELJPE3E2EKEAE1E1KE1CAVR-2313CIPAVR-2313PPINTEGRATED NETWORK AV RECEIVERVer. 3 Some illustrations using in this service manual are slightly different from the actual set. Please use this service manual with referring to the operating instructions without fail. For

2、purposes of improvement, specifications and design are subject to change without notice.Please refer to the MODIFICATION NOTICE.RadioFans.CN 收音机爱 好者资料库2CONTENTSABOUT THIS MANUAL .3What you can do with this manual .3Using Adobe Reader (Windows version) .4SAFETY PRECAUTIONS .6NOTE FOR SCHEMATIC DIAGRA

3、M .7TECHNICAL SPECIFICATIONS .8DIMENSION .8CAUTIONS IN SERVICING .9Initializing INTEGRATED NETWORK AV RECEIVER .9Service Jig .9DISASSEMBLY .101. FRONT PANEL ASSY .122. PCB MX PORT/PCB RS232C .133. PCB HDMI .144. POWER TRANS MAIN .155. PCB SMPS ASSY.156. PCB VIDEO .167. PCB AUDIO .178. PCB PREOUT .18

4、9. PCB SPK .1910. RADIATOR ASSY .2011. PCB REG/REG_CNT ASSY .22SPECIAL MODE .23Special mode setting button .231. com/DSP Version display mode .242. PANEL/REMOTE LOCK Selection mode .283. Service Related Selection mode .294. Remote ID Setup mode .37BLOCK DIAGRAM .39JIG FOR SERVICING .55WHEN THE MICRO

5、PROCESSOR IS REPLACED WITH A NEW ONE .58PROCEDURE FOR UPGRADING THE VERSION OF THE FIRMWARE .581. How to update by DFW .582. How to update by DPMS .623. How to update by USB Memory .69ADJUSTMENT .76SURROUND MODES AND PARAMETERS .77TROUBLE SHOOTING .831. POWER .832. Analog video .843. HDMI/DVI .894.

6、AUDIO .975. Network/USB .1006. SMPS .104CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK .108LEVEL DIAGRAM .109PRINTED WIRING BOARDS .115HDMI .115FRONT HDMI .117REG .117REG CNT .117SIDE CNT.118RC5_MCPORT .119RS232C .119FRONT .120FUNCTION .122F/H_GUIDE .122CNT .122USB .123GUIDE L .123TOP_GUIDE .123GUIDE R .12

7、37CH AMP .124VIDEO .126SPK .127SMPS .129PREOUT .130SCHEMATIC DIAGRAMS .131HDMI SW UNIT .131FRONT HDMI UNIT .132HDMI RX UNIT .133HDMI TX UNIT .134HDMI TX DDR UNIT .135DSP UNIT .136DIR/PLD DIGITAL_IN UNIT .137MAIN DAC UNIT .138DM860A UNIT .139NET PHY UNIT .140CPU UNIT .141CPU LEVEL CHG UNIT .142DIGITA

8、L CNT UNIT .143D.SUPPLY/RESET UNIT .1447CH-AMP UNIT (1/2) .1457CH-AMP UNIT (2/2) .146SPK_SMPS UNIT (1/2) .147SPK_SMPS UNIT (2/2) .148REG_CNT_RS232_RC-5 UNIT (1/4) .149REG_CNT_RS232_RC-5 UNIT (2/4) .150REG_CNT_RS232_RC-5 UNIT (3/4) .151REG_CNT_RS232_RC-5 UNIT (4/4) .152AUDIO UNIT.153VIDEO_PREOUT_TU U

9、NIT (1/3).154VIDEO_PREOUT_TU UNIT (2/3).155VIDEO_PREOUT_TU UNIT (3/3).156FRONT UNIT (1/2) .157FRONT UNIT (2/2) .158WIRING DIAGRAM .159EXPLODED VIEW .160PARTS LIST OF EXPLODED VIEW .161PACKING VIEW .164PARTS LIST OF PACKING & ACCESSORIES .165SEMICONDUCTORS .1661. ICs .1662. FL DISPLAY.196PARTS LIST O

10、F PCB UNIT .1997CH_AMP PCB UNIT ASSY .199SPK_SMPS PCB UNIT ASSY .206REG_CNT PCB UNIT ASSY .210FRONT PCB UNIT ASSY .212AUDIO PCB UNIT ASSY .215VPT PCB UNIT ASSY .217HDMI PCB UNIT ASSY .220RadioFans.CN 收音机爱 好者资料库3ABOUT THIS MANUALRead the following information before using the service manual.What you

11、can do with this manualJump to the target of a schematic diagram connectorClick the Ref. No. of the target connector in the red box around a schematic diagram connector. The screen jumps to the target connector. Page magnification stays the same as before the jump.Search for a Ref. No. (phrase)(Ctrl

12、+Shift+F)You can use the search function in Acrobat Reader to search for a Ref. No. in schematic diagrams, printed wiring board diagrams, block diagrams, and parts lists.1.Press Ctrl+Shift+F on the keyboard. The Search window appears.CtrlShiftF2.Enter the Ref. No. you want to search for in the Searc

13、h window, and then click the Search button. A list of search results appears.3.Click an item on the list. The screen jumps to the page for that item, and the search phrase is displayed.4Using Adobe Reader (Windows version) Properties Click this button and check that the printer is set to a suitable

14、paper size. Page to print Select the following checkbox. More Options : Current View Page Sizing & Handling Select the following checkbox. Size / Size Options : FitAdd notes to this data (Sign)The Sign function lets you add notes to the data in this manual.Save the file once you have finished adding

15、 notes.Example using Adobe Reader XOn the View menu, click Sign. The Sign pane appears.Example using Adobe Reader 9On the Document menu, click Sign. Magnify schematic / printed wiring board diagrams - 1(Ctrl+Space, mouse operation)Example using Adobe Reader 9,XPress Ctrl+Space on the keyboard and dr

16、ag the mouse to select the area you want to view. The selected area is magnified.CtrlSpace0 When you want to move the area shown, hold down Space and drag the mouse. When you want to show a full page view, press Ctrl+0 on the keyboard.Print a magnified part of the manualThe Properties dialog box and

17、 functions will vary depending on your printer.1. Drag the mouse to magnify the part you want to print.2. On the File menu, click Print.3. Configure the following settings in the Print dialog box.4. Click the Print button to start printing.5Magnify schematic / printed wiring board diagrams - 2(Pan &

18、 Zoom function)The Pan & Zoom function lets you see which part of a magnified diagram is being shown in a separate window.Example using Adobe Reader XOn the View menu, point to Zoom, and then click Pan & Zoom. The Pan & Zoom window appears on the screen.Example using Adobe Reader 9On the Tools menu,

19、 point to Select & Zoom, and then click Pan & Zoom Window.Magnify schematic / printed wiring board diagrams - 3(Loupe Tool function)The Loupe Tool function lets you magnify a specific part of a diagram in a separate window.Example using Adobe Reader XOn the View menu, point to Zoom, and then click L

20、oupe Tool. The Loupe Tool window appears on the screen.Example using Adobe Reader 9On the Tools menu, point to Select & Zoom, and then click Loupe Tool Window.6SAFETY PRECAUTIONSThe following items should be checked for continued protection of the customer and the service technician.LEAKAGE CURRENT

21、CHECKBefore returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defect

22、ive. Be sure to test for leakage current with the AC plug in both polarities, in addition, when the sets power is in each state (on, off and standby mode), if applicable.CAUTION Please heed the following cautions and instructions during servicing and inspection. Heed the cautions!Cautions which are

23、delicate in particular for servicing are labeled on the cabinets, the parts and the chassis, etc. Be sure to heed these cautions and the cautions described in the handling instructions. Cautions concerning electric shock!(1) An AC voltage is impressed on this set, so if you touch internal metal part

24、s when the set is energized, you may get an electric shock. Avoid getting an electric shock, by using an isolating transformer and wearing gloves when servicing while the set is energized, or by unplugging the power cord when replacing parts, for example.(2) There are high voltage parts inside. Hand

25、le with extra care when the set is energized. Caution concerning disassembly and assembly!Through great care is taken when parts were manufactured from sheet metal, there may be burrs on the edges of parts. The burrs could cause injury if fingers are moved across them in some rare cases. Wear gloves

26、 to protect your hands. Use only designated parts!The sets parts have specific safety properties (fire resistance, voltage resistance, etc.). Be sure to use parts which have the same properties for replacement. The burrs have the same properties. In particular, for the important safety parts that ar

27、e indicated by the z mark on schematic diagrams and parts lists, be sure to use the designated parts. Be sure to mount parts and arrange the wires as they were originally placed!For safety seasons, some parts use tapes, tubes or other insulating materials, and some parts are mounted away from the su

28、rface of printed circuit boards. Care is also taken with the positions of the wires by arranging them and using clamps to keep them away from heating and high voltage parts, so be sure to set everything back as it was originally placed. Make a safety check after servicing!Check that all screws, part

29、s and wires removed or disconnected when servicing have been put back in their original positions, check that no serviced parts have deteriorate the area around. Then make an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety i

30、s ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and on the power. Using a 500V insulation resistance tester, check that the insulation resistance value between the inplug and the externally exposed metal parts (antenna terminal,

31、 headphones terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired.Many of the electric and the structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and the use of repla

32、cement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and the parts list in this service manual. Be sure to replace them with the

33、parts which have the designated part number.(1) Schematic diagrams .Indicated by the z mark.(2) Parts lists .Indicated by the z mark.The use of parts other than the designated parts could cause electric shocks, fires or other dangerous situations.CAUTION Concerning important safety parts7NOTE FOR SC

34、HEMATIC DIAGRAMWARNING:Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.CAUTION:Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the l

35、eakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.WARNING:DO NOT return the set to the customer unless the problem is identified and remedied.NOTICE:ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000

36、,000 OHMALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO FARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.Parts indicated by nsp on this table cannot be supp

37、lied.When ordering a part, make a clear distinction between 1 and I (i) to avoid mis-supplying.A part ordered without specifying its part number can not be supplied. General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list. (Refer to the Schematic Diagram f

38、or those parts.)Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Part indicated by mark is not illustrated in the

39、exploded view.WARNING:1.2.3.4.5.6.ResistorsRD:CarbonRC:CompositionRS :Metal oxide filmRW:windingRN:Metal filmRK :Metal mixtureP:Pulse-resistant typeNL :Low noise typeNB :Non-burning typeFR :Fuse-resistorF:Lead wire forming2B :1/8 W2E :1/4 W2H :1/2 W3A :1 W3D :2 W3F :3 W3H :5 WF:1%G:2%J:5%K:10%M :20%

40、Ex.:RNType14KShapeand per-formance2EPower182Resist-anceGAllowableerrorFROthers* Resistance1800ohm=1.8kohm1 82Indicates number of zeros after effective number.2-digit effective number.1.2ohm1 R22-digit effective number, decimal point indicated by R.1-digit effective number.: Units: ohmNOTE FOR PARTS

41、LIST8TECHNICAL SPECIFICATIONS n Audio Section Power amplifierRated output (for 2313CI model) :Front : 105 W + 105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W + 135 W (6 , 1 kHz with 0.7 % T.H.D.)Center :105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W (6 , 1 kHz with 0.7 % T.H.D.)Surround :105 W +

42、105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W + 135 W (6 , 1 kHz with 0.7 % T.H.D.)Surround back:105 W + 105 W (8 , 20 Hz 20 kHz with 0.08 % T.H.D.)135 W + 135 W (6 , 1 kHz with 0.7 % T.H.D.)Output connectors : 6 16 AnalogInput sensitivity/Input impedance : 200 mV/47 kFrequency response: 10 Hz 10

43、0 kHz +1, 3 dB (DIRECT mode)S/N : 100 dB (IHFA weighted, DIRECT mode) n Video section Standard video connectorsInput/output level and impedance : 1 Vp-p, 75 Frequency response : 5 Hz 10 MHz 0, 3 dB Color component video connectorInput/output level and impedance : Y (brightness) signal 1 Vp-p, 75 PB

44、/ CB signal 0.7 Vp-p, 75 PR / CR signal 0.7 Vp-p, 75 Frequency response : 5 Hz 60 MHz 0, 3 dB n Tuner section(Note: V at 75 , 0 dBf = 1 x 1015 W)Receiving Range (for E3 model) : 87.5 MHz 107.9 MHzUsable Sensitivity :1.2 V (12.8 dBf)50 dB Quieting Sensitivity :MONO 2.8 V (20.2 dBf)S/N :MONO 70 dB (IH

45、FA weighted, DIRECT mode)STEREO 67 dB (IHFA weighted, DIRECT mode)Total harmonic Distortion :MONO 0.7 % (1 kHz)STEREO 1.0 % (1 kHz) n GeneralPower supply (for E3 model) : AC 120 V, 60 HzPower supply (for E2 model) : AC 230 V, 50/60 HzPower supply (for E1C model) : AC 220 V, 50 HzPower consumption :

46、600 WPower consumption in standby mode : 0.1 WPower consumption in CEC standby mode : 0.5 WPower comsumption in network standby mode : 2.7 WWeight : 10.9 kg4343446086.035.830.2338.518.51521671554.0214.522.0245DIMENSIONAVR-2313CIE3 model9CAUTIONS IN SERVICINGInitializing INTEGRATED NETWORK AV RECEIVE

47、RINTEGRATED NETWORK AV RECEIVER initialization should be performed when the com, peripheral parts of com, and Digital PCB were replaced.1. Turn off the power pressing Power operation (X) button.2. Press Power operation (X) button while simultaneously while pressing ZONE2/REC SOURCE and DIMMER button

48、s.3. Check that the entire display is flashing at intervals of about 1 second, and then release the 2 buttons. The microprocessor will be initialized.AVR-2313CIE3 modelService Jig When you repair the printing board, you can use the following JIG (Extension cable kit).Please order it from Denon Offic

49、ial Service Distributor in your region if necessary.8U-110084S : EXTENSION UNIT KIT : 1 Set(Refer to 55 page.)NOTE: If step 3 fails, start over from step 1. All user settings will be lost and the factory setting will be recovered after the set is initialized. So make sure to note down your setting b

50、eforehand for restoring after the initialization.(X)ZONE2 / REC SOURCEDIMMER10DISASSEMBLY Disassemble in order of the arrow in the following figure. In the case of the re-assembling, assemble it in order of the reverse of the following flow. In the case of the re-assembling, observe attention of ass