Denon-AVR3311CI-avr-sm维修电路原理图.pdf

《Denon-AVR3311CI-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-AVR3311CI-avr-sm维修电路原理图.pdf（216页珍藏版）》请在收音机爱好者资料库上搜索。

1、D&M Holdings Inc.SERVICE MANUALeeMODELJPE3E2EKKAE1E1KE1CAVR-3311CIPAVR-3311PPAV SURROUND RECEIVERVer. 4Some illustrations using in this service manual are slightly different from the actual set.Please use this service manual with referring to the operating instructions without fail.For purposes of i

2、mprovement, specifications and design are subject to change without notice.S0121-0V04DM/DG1008sPlease refer to the MODIFICATION NOTICE.RadioFans.CN 收音机爱 好者资料库2SAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT

3、 CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. if the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defec

4、tive. Be sure to test for leakage current with the AC plug in both polarities, in addition, in each power ON, OFF and STANDBY mode, if applicable.CAUTION Please heed the points listed below during servicing and inspection. Heed the cautions!Spots requiring particular attention when servicing, such a

5、s the cabinet, parts, chassis,etc., have cautions indicated on labels. be sure to heed these causions and the cautions indicated in the handling instructions. Caution concerning electric shock!(1) An AC voltage is impressed on this set, so touching internal metal parts when the set is energized coul

6、d cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc.(2) Tere are high voltage parts inside. Handle with extra care when the set is energized.

7、 Caution concerning disassembly and assembly!Through great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. Only use designated parts!The s

8、ets parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same poroperties. In particular, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the designated parts.

9、 Be sure to mount parts and arrange the wires as they were originally!For safety seasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wores omsode amd clamps are use

10、d to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. Inspect for safety after servicing!Check that all screws, parts and wires removed or disconnected for servicing have been put back in their original positions, inspect that no parts arou

11、nd the area that has been serviced have been negatively affected, conduct an inslation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured.(Insulation check procedure)Unplug the power cord from the power outlet, disconnect the a

12、ntenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the inplug and the externally exposed metal parts (antenna terminal, headphones terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired.Many of the

13、 electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be pore

14、served. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designated part number.(1) Schematic diagrams .Indicated by the z mark.(2) Parts lists .Indicated by the z mark.Using parts oth

15、er than the designated parts could result in electric shock, fires or other dangerous situations.CAUTION Concerning important safety partsRadioFans.CN 收音机爱 好者资料库3NOTE FOR SCHEMATIC DIAGRAMWARNING:Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by

16、 the manufacturer.CAUTION:Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohm

17、s, the unit is defective.WARNING:DO NOT return the unit to the customer until the problem is located and corrected.NOTICE:ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHMALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CON

18、DITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.Parts for which nsp is indicated on this table cannot be supplied.When ordering of part, clearly indicate 1 and I (i) to avoid mis-supplying.Ordering part without stating its part number can not be supplied. Not including General-p

19、urpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.Not including General-purpose Carbon Film Resistor in the P.W.Board part

20、s list. (Refer to the Schematic Diagram for those parts.)Part indicated with the mark is not illustrated in the exploded view.WARNING:1.2.3.4.5.6.ResistorsRD:CarbonRC:CompositionRS :Metal oxide filmRW:windingRN:Metal filmRK :Metal mixtureP:Pulse-resistant typeNL :Low noise typeNB :Non-burning typeFR

21、 :Fuse-resistorF:Lead wire forming2B :1/8 W2E :1/4 W2H :1/2 W3A :1 W3D :2 W3F :3 W3H :5 WF:1%G:2%J:5%K:10%M :20%Ex.:RNType14KShapeand per-formance2EPower182Resist-anceGAllowableerrorFROthers* Resistance1800ohm=1.8kohm1 82Indicates number of zeros after effective number.2-digit effective number.1.2oh

22、m1 R22-digit effective number, decimal point indicated by R.1-digit effective number.: Units: ohmCapacitorsCE :Aluminum foilelectrolyticCA :Aluminium solidelectrolyticCS :Tantalum electrolyticCQ:FilmCK :CeramicCC:CeramicCP :OilCM:MicaCF :MetallizedCH:MetallizedHS :High stability typeBP :Non-polar ty

23、peHR:Ripple-resistant typeDL :For change and dischargeHF :For assuring high requencyU:UL partC:CSA partW :UL-CSA partF:Lead wire forming0J :6.3 V1A :10 V1C :16 V1E :25 V1V :35 V1H :50 V2A :100 V2B :125 V2C :160 V2D :200 V2E :250 V2H :500 V2J :630 VF:1%G:2%J:5%K:10%M :20%Z:80%:- 20%P:+100%C:0.25pFD:0

24、.5pF=:OthersEx.:CEType04WShapeand per-formance1HDielectricstrength3R2CapacityMAllowableerrorBPOthers Units:F.2200F2 22Indicates number of zeros after effective number.2-digit effective number. Units:F.2.2F2 R22-digit effective number, decimal point indicated by R1-digit effective number.*Capacity (e

25、lectrolyte only)When the dielectric strength is indicated in AC,AC is included after the dieelectric strength value.*Capacity (except electrolyte) Units:pF2200pF=0.0022F2 22Indicates number of zeros after efective number. (More than 2)2-digit effective number. Units:pF220pF2 212-digit effective numb

26、er.Indicates number of zeros after effective numver. (0 or 1)NOTE FOR PARTS LIST4TECHNICAL SPECIFICATIONS s n Audio SectionPower amplifierRated output :Front:125W+125W(8,20Hz20kHzwith0.05%T.H.D.)165W+165W(6,1kHzwith0.7%T.H.D.)Center:125W(8,20Hz20kHzwith0.05%T.H.D.)165W(6,1kHzwith0.7%T.H.D.)Surround:

27、125W+125W(8,20Hz20kHzwith0.05%T.H.D.)165W+165W(6,1kHzwith0.7%T.H.D.)Surroundback/Frontheight/Frontwide:125W+125W(8,20Hz20kHzwith0.05%T.H.D.)165W+165W(6,1kHzwith0.7%T.H.D.)Dynamic power : 130Wx2ch(8)190Wx2ch(4)Output connectors : 616AnalogInput sensitivity/Input impedance : 200mV/47kFrequency respons

28、e: 10Hz100kHz+1,3dB(DIRECTmode)S/N: 102dB(IHFAweighted,DIRECTmode)Distortion: 0.005%(20Hz20kHz)(DIRECTmode)Rated output: 1.2VDigitalD/A output: Ratedoutput2V(at0dBplayback)Totalharmonicdistortion0.008%(1kHz,at0dB)S/Nratio102dBDynamicrange100dBDigital input: FormatDigitalaudiointerfacePhono equalizer

29、 (PHONO input REC OUT)Input sensitivity: 2.5mVRIAA deviation: 1dB(20Hzto20kHz)S/N: 74dB(Aweighting,with5mVinput)Rated output: 150mVDistortion factor: 0.03%(1kHz,3V) n Video SectionStandard video connectorsInput/output level and impedance : 1Vp-p,75Frequency response : 5Hz10MHz+1,3dBColor component v

30、ideo connectorInput/output level and impedance : Y(brightness)signal1Vp-p,75PB/CBsignal0.7Vp-p,75PR/CRsignal0.7Vp-p,75Frequency response : 5Hz60MHz+0,3dB(when“VideoConvert”setto“OFF”) n HD Radio section (forE3)FM(Note:Vat75,0dBf=1x1015W)Receiving Range :FM 87.5MHz107.9MHzAM530kHz1710kHzUsable Sensit

31、ivity :FM1.5V(14.8dBf)AM20VS/N (IHF-A) :FMMONO78dBAMSTEREO68dBHD85dB85dBTotal harmonic Distortion (at 1 kHz) :FMMONO0.1%AMSTEREO0.2%HD0.02%0.02% n Tuner section (forE2,E1C)FM(Note:Vat75,0dBf=1x1015W)Receiving Range :FM 87.5MHz108.0MHzAM522kHz1611kHzUsable Sensitivity :FM1.2V(12.8dBf)AM18V50 dB Quiet

32、ing Sensitivity :FMMONO2.0V(17.3dBf)STEREO42V(34.5dBf)S/N (IHF-A) :FMMONO72dBSTEREO67dBTotal harmonic Distortion (at 1 kHz) :FMMONO0.3%STEREO0.7% n GeneralPower supply : AC120V,60Hz(forE3)AC230V,50Hz(forE2)AC220V,50Hz(forE1C)Power consumption :670W0.1W(Standby)2.2W(CECstandby)Maximum external dimens

33、ions :434(W)x171(H)x381(D)mm(17-3/32”x6-47/64”x15”)Weight : 12.2kg(26lbs14.3oz) n Remote Control Unit (RC-1146)Batteries : R6/AAType(twobatteries)Maximum external dimensions :53(W)x224(H)x28(D)mm(2-3/32”x8-13/16”x1-7/64”)Weight : 160g(5.6oz,includingbatteries) n Remote Control Unit (RC-1148)Batterie

34、s : R03/AAAType(twobatteries)Maximum external dimensions : 49(W)x220(H)x24.5(D)mm(1-59/64”x8-21/32”x31/32”)Maximum external dimensions : 114g(Approx4oz,includingbatteries)DIMENSION21.420.554.7214.5338.9380.844.28535.534.5266344434161551715CAUTION IN SERVICINGBefore the Digital P.W.B. are replacedIf

35、you cannot specify the cause of the digital PWB defect, carry out Initializing Update to latest firmware.The defect may be cleared. See the following for the method of initializing the com.Initializing AV SURROUND RECEIVERAV SURROUND RECEIVER initialization should be performed when the com, peripher

36、al parts of com, and Digital P.W.B. are replaced.1. Turn off the power using ON/STANDBY button.2. Press ON/STANDBY button while simultaneously pressing STANDARD and DSP SIMULATION buttons.3. Check that the entire display is flashing with an interval of about 1 second, and release your fingers from t

37、he 2 buttons and the microprocessor will be initialized.Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to Denon Official Service Distributor in your region if necessary.8U-110084S : EXTENSION UNIT KIT : 1 Set(Refer to 21 page)Note:

38、If step 3 does not work, start over from step 1. All user settings will be lost and this factory setting will be recovered when this initialization mode. So make sure to memorize your setting for restoring after the initialization.2,31,2 6DISASSEMBLY s Disassembleinorderofthearrowofthefigureoffollow

39、ingflow. Inthecaseofthere-assembling,assembleitinorderofthereverseofthefollowingflow. Inthecaseofthere-assembling,observeattentionofassemblingit. Ifwirebundlesareuntiedormovedtoperformadjustmentorpartsreplacementetc.,besuretorearrangethemneatlyastheywereoriginallybundledorplacedafterward.Otherwise,i

40、ncorrectarrangementcanbeacauseofnoisegeneration.FRONT PANEL ASSYReferto DISASSEMBLY 1. FRONT PANEL ASSYandEXPLODED VIEWPCBFRONT(Ref.No.ofEXPLODEDVIEW:P1)PCBFUNCTION(Ref.No.ofEXPLODEDVIEW:P2)PCBCNT(Ref.No.ofEXPLODEDVIEW:P3)PCBV.AUX_HP(Ref.No.ofEXPLODEDVIEW:P4)PCBUSB(Ref.No.ofEXPLODEDVIEW:P5)PCBMIC(Re

41、f.No.ofEXPLODEDVIEW:P6)PCBFRONTHDMI(Ref.No.ofEXPLODEDVIEW:P29)TRANS MAINReferto DISASSEMBLY 5. TRANS MAINandEXPLODED VIEWTRANSMAIN(Ref.No.ofEXPLODEDVIEW:44)HEAT SINK ASSYReferto DISASSEMBLY 2. HEAT SINK ASSYandEXPLODED VIEWPCBGUIDE_TOP(Ref.No.ofEXPLODEDVIEW:P7)PCBGUIDE_L(Ref.No.ofEXPLODEDVIEW:P8)PCB

42、7CH-AMPASSY(Ref.No.ofEXPLODEDVIEW:P10)PCB REG CNT/PCB REGReferto DISASSEMBLY 3. PCB REG CNT/PCB REGandEXPLODED VIEWPCBREG(Ref.No.ofEXPLODEDVIEW:P11)PCBREG_CNT(Ref.No.ofEXPLODEDVIEW:P12)CABINET TOPHDMI UNIT ASSYReferto DISASSEMBLY 4. HDMI UNIT ASSYandEXPLODED VIEWPCBPREOUT(Ref.No.ofEXPLODEDVIEW:P13)P

43、CBSIDE_CNT(Ref.No.ofEXPLODEDVIEW:P14)PCBAUDIO(Ref.No.ofEXPLODEDVIEW:P15)PCBVIDEOASSY(Ref.No.ofEXPLODEDVIEW:P16)PCBHDMI(Ref.No.ofEXPLODEDVIEW:P17)PCBRS232(Ref.No.ofEXPLODEDVIEW:P18)PCBSIRIUS(Ref.No.ofEXPLODEDVIEW:P19)PCBSPK(Ref.No.ofEXPLODEDVIEW:P20)PCBSMPS(Ref.No.ofEXPLODEDVIEW:P21)PCBF_WIDE(Ref.No.

44、ofEXPLODEDVIEW:P22)PCBFRONT_CNT(Ref.No.ofEXPLODEDVIEW:P23)7About the photos used for descriptions in the DISASSEMBLY section. ThedirectionfromwhichthephotographsusedhereinwerephotographedisindicatedatDirectionofphotograph:*attheleftoftherespectivephotographs. Refertothetablebelowforadescriptionofthe

45、directioninwhichthephotosweretaken. Photographsforwhichnodirectionisindicatedweretakenfromabovetheproduct.The viewpoint of each photograph(Photografy direction)View from aboveFront sideDirection of photograph: BDirection of photograph: DDirection of photograph: CDirection of photograph: A81. FRONT P

46、ANEL ASSY(1) Removethescrews.(2) Cutthewireclampband,thendisconnecttheconnectorwiresandFFCcable.Removethescrews.CABINET TOPFRONT PANEL ASSYProceeding : View from bottomSTYLE PIN : LooseSTYLE PIN : LooseN4201CP100FFC cableFFC cablecutPleaserefertoEXPLODEDVIEWforthedisassemblymethodofeachPCBincludedin

47、FRONTPANELASSY.92. HEAT SINK ASSY(1) Removethescrews.(2) Cutwireclampband,thenremovethescrews.Disconnecttheconnectorwires.CABINET TOPHEAT SINK ASSYProceeding : View from bottomDirection of photograph: DDirection of photograph: CSTYLE PIN : LooseCP100cut10(3) Removethescrews.(4) Cutthewireclampbands,

48、thendisconnecttheconnectorwiresandFFCcable.Removethescrews,SUPPORTERP.C.andtheHDMIBRACKET.(5) Disconnecttheconnectorwires.Direction of photograph: ACUSHION BRACKETSTYLE PIN : LooseN4201N4905FFC cableFFC cablecutHEATSINK ASSYHDMI BRACKETSUPPORTER P.C.CP401CP402CP405CP403STYLE PIN : LoosePCB 7CH AMPPl

49、easerefertoEXPLODEDVIEWforthedisassemblymethodofeachP.W.BincludedinHEATSINKASSY.113. PCB REG CNT/PCB REG(1) Removethescrews.(2) Disconnecttheconnectorwiresandconnectorboard.CABINET TOPHEAT SINK ASSYPCB REG CNT/PCB REGProceeding : PCB REGCP102CP104N2004Board to boardCP13APCB REGPCB REG CNTDirection o

50、f photograph: C124. HDMI UNIT ASSY(1) Removethescrews,thenremovetheBACKPANELandtheHDMIBRACKET.(2) Cutwireclampband,thendisconnecttheconnectorwiresandtheFFCcables.RemovethescrewsandtheSUPPORTERP.C.RemovethePCBSIRIUSandthePCBRS232fromthePCBSIDECNT(Boardtoboard).CABINET TOPHDMI UNIT ASSYProceeding : Di