HarmanKardon-AVR154-avr-sm维修电路原理图.pdf

上传人:cc518 文档编号:147049 上传时间:2024-08-23 格式:PDF 页数:140 大小:13.50MB
下载 相关 举报
HarmanKardon-AVR154-avr-sm维修电路原理图.pdf_第1页
第1页 / 共140页
HarmanKardon-AVR154-avr-sm维修电路原理图.pdf_第2页
第2页 / 共140页
HarmanKardon-AVR154-avr-sm维修电路原理图.pdf_第3页
第3页 / 共140页
亲,该文档总共140页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《HarmanKardon-AVR154-avr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-AVR154-avr-sm维修电路原理图.pdf(140页珍藏版)》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR154 AVR154 5 X 30W 5.1 CHANNEL A/V RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGING.5 FRONT PANEL CONTROLS.6 REAR PANEL CONNECTIONS.8 REMOTE CONTROL FUNCTIONS.10 CONNECTIONS/INSTALLATION.13 OPERATION.24 TROUBLESHOOTING GUIDE.29 REMOT

2、E & PROCESSOR RESETS.30 DISASSEMBLY.31 UNIT EXPLODED VIEW.32 EXPLODED VIEW PARTS LIST33 AMP BIAS ADJUSTMENT.34 BLOCK DIAGRAM.35 PCB DRAWINGS36 ELECTRICAL PARTS LIST.42 SEMICONDUCTOR PINOUTS.71 SCHEMATICS.132 WIRING DIAGRAM.140 harman/kardon, Inc. 250 Crossways Park Dr. Released 2008 Woodbury, New Yo

3、rk 11797 Rev0 5/2008 Discontinued XXXX RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designated

4、, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the customer

5、.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The following

6、techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obtai

7、n and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, t

8、oprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to damag

9、e ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads el

10、ectrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed.B

11、e sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floor

12、can generate static electricity sufficient to damage an ES devices.CAUTION :AVR154 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库2SAFETY PRECAUTIONSThe following check should be performed for the continuedprotection of the customer and service technician.LEAKAGE CURRENT CHECKMeasure leakage curr

13、ent to a known earth ground (waterpipe, conduit, etc.) by connecting a leakage current testerbetween the earth ground and all exposed metal parts of theappliance (input/output terminals, screwheads, metaloverlays, control shaft, etc.). Plug the AC line cord of theappliance directly into a 120V AC 60

14、Hz outlet and turn theAC power switch on. Any current measured must not exceedo.5mA.ANY MEASUREMENTS NOT WITHIN THE LIMITSOUTLINED ABOVE ARE INDICATIVE OF APOTENTIAL SHOCK HAZARD AND MUST BECORRECTED BEFORE RETURNING THE APPLIANCETO THE CUSTOMER.DeviceundertestTest allexposed metalsurfacesAlso test

15、withplug reversed(Using AC adapterplug as required)AC Leakage TestLeakagecurrenttesterReading shouldnot be above0.5mAEarthgroundAVR154 harman/kardonharman/kardon 3AVR 154 TECHNICAL SPECIFICATIONSAudio SectionStereo Mode Continuous Average Power (FTC)40 Watts per channel, 20Hz20kHz, 0.07% THD, both c

16、hannels driven into 8 ohmsFive-Channel Surround Modes Power per Individual ChannelFront L&R channels:30 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:30 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround (L & R Side) channels:30 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput

17、Sensitivity/ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)100dBSurround System Adjacent Channel SeparationPro Logic I/II 40dBDolby Digital (AC-3)55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz 130kHzHigh Instantaneous Current Capability (HCC)25 AmpsTransient Intermodulation

18、 Distortion (TIM)UnmeasurableSlew Rate40V/secFM Tuner SectionFrequency Range87.5108.0MHzUsable SensitivityIHF 1.3V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequenc

19、y Range5201720kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response (Composite and S-Video)10Hz8MHz (3dB)Video Frequency

20、Response (Component Video) 10Hz100MHz (3dB)HDMISwitchingGeneralPower RequirementAC 120V/60HzPower Consumption65W idle, 540W maximum (5 channels driven)Dimensions (Product)(Shipping)Width17-5/16 inches (440mm)22 inches (559mm) Height6-1/2 inches (165mm)10-1/2 inches (267mm) Depth15 inches (382mm)18-3

21、/4 inches (476mm)(Product)(Shipping)Weight 20.5 lb (9.3kg)25.3 lb (11.5kg)Depth measurement includes knobs, buttons and terminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon and Logic 7 are trademarks of H

22、arman International Industries, Incorporated, registered in the United States and/or other countries. Designed to Entertain is a trademark of Harman InternationalIndustries, Incorporated.Blu-ray Disc is a trademark of the Blu-ray Disc Association.Cirrus Logic is a registered trademark of Cirrus Logi

23、c, Inc.Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.Manufactured under license from Dolby Laboratories.Manufactured under license under U.S. Patent #s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending

24、. DTS, DTS Digital Surround,ES, and Neo:6 are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. 1996-2007 DTS, Inc.All rights reserved.HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).HDMI is a trademark or registered trademark of HDMI Licens

25、ing LLC.iPod is a trademark of Apple Inc., registered in the U.S. and other countries.SACD is a trademark of Sony Corporation.TiVo is a registered trademark of TiVo Inc.Please register your AVR 154 on our Web site at . Note:Youll need the products serial number.At the same time, you can choose to be

26、 notified about our new products and/or special promotions.AVR154 harman/kardonharman/kardon 4POLY BAGNODESCRIPTIONPARTS NO.Q,ty123456711CPB1061WPOLY BAG1. Instruction manual assy - AccessoriesSHEET GUIDE(QUICK START GUIDE)STAPLE108CPL0905CQE1A379Z311CARTAVR154CABR03P3CSA1A020ZREMOCON TRANSMITTER AS

27、SYAM LOOP ANTENNABATTERY113CARD WARRANTYCQE1A172X1INSTRUCTION MANUALFM 1 POL ANT(UL)CQX1A1309ZCSA1A019Z11CARD WARRANTYSHEET GUIDE2BATTERY ASSY4REMOCONTRANSMITTER ASSY873AM LOOP ANTENNA ASSYMANUAL INSTRUCTION5FM 1 POLE ANT(UL)6STAPLESHEET,FRONT COVERCOVER BCOVER ABAG,POLYPAD, COVERCQE1A219ZCGR1A332H6

28、3CPS1A676CPB1A176ZCGR1A331H631 11111COVER ASSYCGRAVR154ZA154321COVER ASSY910IMAGE BROCHURES11HQE1A273Z1IMAGE BROCHURES119MANUAL ASSYBOX,OUT CARTON4512DESCRIPTIONNOCPS5A564CQXAVR154CPG1A854Z111Q,tyPARTS NO.CPS5A565SNOW,PAD(R)31SNOW,PAD(L)SET1A2. Package DrawingAVR154SNOW PAD (R)3BOX ,OUT CARTON54SNOW

29、 PAD (L)2MANUAL ASSY1AVR154AVR154AVR 154visit 58Main Power Switch:This mechanical switch turns the power supplyon or off. It is usually left pressed in (On position), and cannot be turnedon using the remote control.Standby/On Switch:This electrical switch turns the receiver on for playback, or leave

30、s it in Standby mode for quick turn-on using thisswitch or the remote control.Power Indicator:This LED has four possible modes: Main Power Off: When the AVR is unplugged or the Main PowerSwitch is off, this LED remains unlit. Standby: This LED turns amber, indicating that the AVR is ready to be turn

31、ed on. On: This LED turns white, and the AVR operates normally. Protect: If this LED ever turns red, turn off the AVR and unplug it.Check all speaker wires for a possible short. If none is found, bringthe unit to an authorized Harman Kardon service center for inspectionand repair before using it aga

32、in.When the main power is turned off, the LED is dark and the receiverwont respond to any button presses.When the main power is turnedon, but before the Standby/On Switch is used, the LED turns amber toindicate that the receiver is in standby mode and is ready to be turnedon.When the receiver is tur

33、ned on, the LED turns white.Source Select:Press this button to select a source device, which is a component where a playback signal originates, e.g., DVD, CD,cable TV, satellite or HDTV tuner.The sources name will appear in the Message Display.Volume Knob:Turn this knob to raise or lower the volume,

34、 which will be shown in decibels (dB) in the Message Display.Message Display:Various messages appear in this two-line displayin response to commands and changes in the incoming signal. In normal operation, the current source name and the analog or digitalaudio input assigned to it appear on the uppe

35、r line, while the surroundmode is displayed on the lower line.When the on-screen display menusystem (OSD) is in use, the message OSD ON will appear to remind you to check the video display.Tuner Band:Press this button to select the tuner as the source, or to switch between the AM and FM bands.Tuning

36、:Press either side of this button to tune a radio station.Tuning Mode:This button toggles between manual (one frequencystep at a time) and automatic (seeks frequencies with acceptable signalstrength) tuning mode. It also toggles between stereo and mono modeswhen an FM station is tuned.Preset Station

37、s:Press this button to select a preset radio station.Headphone Jack:Plug a 1/4 headphone plug into this jack for private listening.Surround Mode:Press this button to select a surround sound (e.g., multichannel) mode group. Choose from the Dolby modes,DTS modes, Logic 7 modes, DSP modes or Stereo mod

38、es.Surround Select:After you have selected the desired surroundmode group, press this button to select a specific mode.Analog Audio,Video and Digital Audio Inputs:Connect asource component that will only be used temporarily, such as a cameraor game console to these jacks. Use only one type of audio

39、and onetype of video connection.Speaker/Channel Input Indicators:The box icons indicatewhich speaker positions you have configured (see the Initial Setup section), and the size (frequency range) of each speaker.When a digitalaudio input is used, letters will light inside the boxes to indicate whichc

40、hannels are present in the incoming signal.Remote IR Sensor:This sensor receives infrared (IR) commandsfrom the remote control. It is important to ensure that it is not blocked.If covering the sensor is unavoidable, such as when the AVR 154 isplaced inside a cabinet, you may use an optional Harman K

41、ardon HE 1000, or other infrared receiver, with an IR emitter (“blaster”) placed directly over this sensor.FRONT-PANEL CONTROLSAVR154 harman/kardonharman/kardon 69SurroundModeTuningPreset StationsSurroundSelectTuner BandTuning ModeSourceSelectHeadphoneJackDigitalAudio Inputs(Optical 3 andCoaxial 3)V

42、ideo 3Video InputsVideo 3Analog AudioInputsPowerIndicatorMain PowerSwitchStandby/OnSwitchVolumeRemote IR SensorMessage DisplaySpeaker/ChannelInput IndicatorsNOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded

43、 from the Product Support section .AVR154 harman/kardonharman/kardon 710REAR-PANEL CONNECTIONSAM and FM Antenna Terminals:Connect the included AM andFM antennas to their respective terminals for radio reception.Front, Center and Surround Speaker Outputs:Use two-conductor speaker wire to connect each

44、 set of terminals to the correctspeaker. Remember to observe the correct polarity (positive and negativeconnections).Always connect the positive lead to the colored terminalon the receiver and the red terminal on the speaker. Connect the negativelead to the black terminal on both the receiver and th

45、e speaker. See theConnections section for more information on connecting your speakers.Subwoofer Output:If you have a powered subwoofer with a line-level input, connect it to this jack.Video 1,Video 2 and DVD Audio/Video Inputs:These jacksmay be used to connect your video-capable source components (

46、e.g.,VCR, DVD player, cable TV box) to the receiver.NOTE: If a source is HDMI-capable, it is preferable to connect itto one of the AVRs HDMI Inputs. If HDMI is not available on thesource, then select one of the following types of video connectionfor each source device, in order of preference: compon

47、entvideo, S-video or composite video.See the Connections section for more information on audio and videoconnection options.Video 1 Audio/Video Outputs:These jacks may be used to connect your VCR or another recorder.Composite and S-Video Monitor Outputs:If any of yoursources use composite or S-video

48、connections, connect one or both of these monitor outputs to the corresponding inputs on your televisionor video display.CD and Tape Audio Inputs:These jacks may be used to connectaudio-only source components (e.g., CD player, tape deck). Do not connect a turntable to these jacks unless you are usin

49、g it with a phonopreamp.Tape Outputs:These jacks may be used to connect a CDR oranother audio-only recorder.Coaxial and Optical Digital Audio Inputs:If your source has a compatible digital audio output, connect it to one of these jacksfor improved audio performance. Use only one type of digital audi

50、o connection for each source.Coaxial Digital Audio Output:If a source is also a digital audiorecorder, connect the coaxial digital audio output to the recorders coaxial digital input.AUX Input:Enjoy audio from an iPod (not included), CD player orother portable player by connecting its headphone jack

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 功放/音响/收扩 > HarmanKardon

copyright@ 2008-2025 收音机爱好者资料库 版权所有
备案编号:鄂ICP备16009402-5号