HarmanKardon-AVR210-avr-sm维修电路原理图.pdf

《HarmanKardon-AVR210-avr-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-AVR210-avr-sm维修电路原理图.pdf（135页珍藏版）》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR210 AVR210 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.11 TROUBLESHOOTING GUIDE.14 PROCESSOR RESET.14 IDLE CURRENT/TUNER ALIGNMENT15 BULLETIN # H/K

2、2001-01.16 BULLETIN # H/K2001-03.18 BULLETIN # H/K2003-07.19 TECH TIP# HKTT2002-01.21 TECH TIP# HKTT2003-01.23 TECH TIP# HKTT2004-03.24 UNIT EXPLODED VIEW.28 EXPLODED VIEW PARTS LIST.29 BLOCK DIAGRAMS.30 PCB DRAWINGS.32 ELECTRICAL PARTS LIST.44 SEMICONDUCTOR PINOUTS.65 SCHEMATICS.115 WIRING DIAGRAM.

3、132 PACKAGE135 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 6/2005 RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component id

4、entified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the su

5、pply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect tra

6、nsistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour bod

7、y by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the a

8、ssembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-s

9、tatic can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it

10、. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or ci

11、rcuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes f

12、abric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :2AVR210 AVR210 harman/kardon RadioFans.CN 收音机爱 好者资料库1. Inspect all lead dress to make certain thatleads are not pinched or that hardware is notlodged between the chassi

13、s and other metalpartsintheunit.2. Be sure that any protective devices such asnonmetallic control knobs, insulating fish-papers,cabinetbacks,adjustmentandcompartment covers or shields, isolationresistor-capacitynetworks,mechanicalinsulators, etc. Which were removed for theservicingareproperlyre-inst

14、alled.Before returning the unit to the user, perform the following safety checks :3. Be sure that no shock hazard exists ; check for leakagecurrentusingSimpsonModel229LeakageTester,standardequipment item No. 21641, RCA Model WT540A or usealternate method asfollows : Plug the power cord directlyInto

15、a 120 volt AC receptacle (do not use an IsolationTransformer for this test). Using two clip leads, connect a1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,suchas a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or hi

16、gher sensitivity to measure the AC voltage drop across theresistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal,cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thistest

17、shouldbeperformedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningtheunittotheowner.3AVR210 AVR210 harman/kardon 4 SPECIFICATIONSTechnical SpecificationsAudio SectionStereo Mode Continuous Average Power (FTC)50 Watts per channel, 20Hz20kHz, 0.07%

18、 THD, both channels driven into 8 ohmsFive-Channel Surround Modes Power Per Individual ChannelFront L&R channels:40 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:40 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround channels:40 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput S

19、ensitivity/ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)95dBSurround System Adjacent Channel SeparationAnalog Decoding 40dB(Pro Logic, etc.)Dolby Digital (AC-3)55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz100kHzHigh Instantaneous Current Capability (HCC)25 AmpsTransient

20、Intermodulation Distortion (TIM)UnmeasurableRise Time16secSlew Rate40V/secFM Tuner SectionFrequency Range87.5108MHzUsable SensitivityIHF 1.3 V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection

21、90dBTuner Output Level1kHz, 75kHz Dev 500mVAM Tuner SectionFrequency Range5201710kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance 1Vp-p/75 ohmsVideo Freq

22、uency Response10Hz8MHz (3dB)GeneralPower RequirementAC 120V/60HzPower Consumption72W idle, 580W maximum (2 channels driven)Dimensions (Max)Width17.3 inches (440mm)Height6.5 inches (165mm)Depth17.1 inches (435mm)Weight31 lb (14.1kg)Depth measurement includes knobs, buttons and terminal connections.He

23、ight measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon is a registered trademark, and Power for the Digital Revolution is a trademark,of Harman International Industries, Inc.is a trademark of Harman International Industries, Inc.

24、 (Patent No. 5,386,478).*Manufactured under license from Dolby Laboratories.“Dolby,”“Pro Logic,”“AC-3” and the Double-D symbol aretrademarks of Dolby Laboratories. Confidential UnpublishedWorks. 19921999 Dolby Laboratories, Inc.All rights reserved.DTS and DTS Surround are trademarks of Digital Theat

25、er Systems, Inc.UltraStereo is a trademark of UltraStereo Corp.VMAx is a registered trademark of Harman International Industries, Inc., and is an implementation of Cooper Bauck Transaural Stereo under patent license.Logic 7 is a registered trademark of Lexicon, Inc.Crystal is a registered trademark

26、of Cirrus Logic Corp.TMAVR210 AVR210 harman/kardon 5 FRONT PANEL CONTROLS1 Main Power Switch: Press this button toapply power to the AVR 210.When the switchis pressed in, the unit is placed in a Standbymode, as indicated by the amber LED 3 sur-rounding the System Power Control 2.This button MUST be

27、pressed in to operate theunit.To turn the unit off and prevent the useof the remote control, this switch should bepressed until it pops out from the front panelso that the word “OFF” may be read at thetop of the switch.NOTE: This switch is normally left in the “ON”position.2 System Power Control: Wh

28、en the MainPower Switch 1 is “ON,” press this buttonto turn on the AVR 210; press it again to turnthe unit off. Note that the Power Indicatorsurrounding the switch 3 will turn greenwhen the unit is on.3 Power Indicator: This LED will be illumi-nated in amber when the unit is in the Standbymode to si

29、gnal that the unit is ready to beturned on.When the unit is in operation, theindicator will turn green.4 Headphone Jack:This jack may be used tolisten to the AVR 210s output through a pair ofheadphones. Be certain that the headphoneshave a standard 1/4 stereo phone plug. Notethat the main room speak

30、ers will automaticallybe turned off when the headphone jack is in use.5 Selector Buttons:When you are establish-ing the AVR 210s configuration settings,usethese buttons to select from the choices available,as shown in the Main Information Display .6 Tone Mode: Pressing this button enablesor disables

31、 the Bass and Treble tone controls.When the button is pressed so that the wordsTONE IN appear in the Main InformationDisplay , the settings of the Bass & andTreble ( controls may be used to adjust theoutput signals.When the button is pressed sothat the words TONE OUT appear in the MainInformation Di

32、splay , the output signalwill be “flat, ” without any bass or treble alter-ation, no matter how the actual Bass andTreble controls &( are adjusted.Front Panel Controls1 Main Power Switch2 System Power Control3 Power Indicator4 Headphone Jack5 Selector Buttons6 Tone Mode7 Surround Mode Selector8 Tuni

33、ng Selector9 Tuner Band Selector) Preset Stations Selector! Input Source Selector FM Mode Selector# Digital Optical 3 Input$ Digital Coax 3 Jack% Video 4 Video Input Jacks Video 4 Audio Input Jacks& Bass Control* Balance Control( Treble Control Volume Control Set Button Input Indicators Delay Digita

34、l Input Selector Main Information Display Channel Select Button Speaker Select Button Test Tone Selector Surround Mode Indicators Remote Sensor Window4?135789)!#$%*&(?29?2630?AVR210 AVR210 harman/kardon 6 FRONT PANEL CONTROLSFront Panel Controls7 Surround Mode Selector: Press this but-ton to change

35、the surround mode by scrollingthrough the list of available modes. Note thatdepending on the type of input, some modesare not always available. (See page 25 for moreinformation about surround modes.)8 Tuning Selector: Press the left side of thebutton to tune lower-frequency stations and theright sid

36、e of the button to tune higher-frequencystations.When a station with a strong signal is reached, the TUNED indicator V will be illuminated in the Main Information Display .To tune manually, tap the button lightly andnote that the tuner will step up one frequencyincrement per button press.When the bu

37、tton isheld for a few seconds you will note that theunit will quickly search the frequency band.Release it once the fast tuning starts; the tunerwill automatically scan for the next station withan acceptable signal and then stop.9 Tuner Band Selector: Pressing this buttonwill automatically switch th

38、e AVR 210 to theTuner mode. Pressing it again will switchbetween the AM and FM frequency bands. (Seepage 28 for more information on the tuner.) Preset Stations Selector: Press this button to scroll up or down through the list orstations that have been entered into the presetmemory. (See page 28 for

39、more information ontuner programming.)! Input Source Selector: Press this buttonto change the input by scrolling up or downthrough the list of input sources. FM Mode Selector: Press this button toselect Auto or Manual tuning.When the buttonis pressed so that the AUTO indicator W lights,the tuner wil

40、l search for the next station with anacceptable signal when the Tuning Selector8u is pressed.When the button is pressedso that the AUTO indicator W is not lit, eachpress of the Tuning Selector 8u willincrease the frequency. (See page 28 for moreinformation on using the tuner.)# Digital Optical 3 Inp

41、ut: Connect the opti-cal digital output of an audio or video product tothis jack.When the Input is not in use, be certainto keep the plastic cap installed to avoid dustcontamination that might degrade future performance.$ Digital Coax 3 Jack: This jack is used forconnection to the output of portable

42、 audiodevices, video game consoles or other productsthat have a coax digital jack.% Video 4 Video Input Jacks: These jacksmay be used for temporary connection to thecomposite or S-Video output of video games,camcorders or other portable video products. Video 4 Audio Input Jacks: Theseaudio/video jac

43、ks may be used for temporaryconnection to video games or portableaudio/video products such as camcorders andportable audio players.& Bass Control:Turn this control to modifythe low frequency output of the left/right chan-nels by as much as 10dB.Set this control to asuitable position for your taste o

44、r room acoustics.* Balance Control: Turn this control tochange the relative volume for the frontleft/right channels.NOTE: For proper operation of the surroundmodes this control should be at the midpoint or “12 oclock” position.(Treble Control:Turn this control to modifythe high frequency output of t

45、he left/right chan-nels by as much as 10dB.Set this control to asuitable position for your taste or room acoustics. Volume Control: Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR 210 is muted,adjusting volume control will automaticallyrelease the u

46、nit from the silenced condition. Set Button:When making choices duringthe setup and configuration process, press thisbutton to enter the desired setting as shown in the Main Information Display into the AVR 210s memory.The set button may also be used to change the display brightness.(See page 31.) I

47、nput Indicators: A green LED will light infront of the input that is currently being used asthe source for the AVR 210. Delay: Press this button to begin thesequence of steps required to enter delay timesettings. (See page 18 for more information ondelay times.) Digital Input Selector: When playing

48、asource that has a digital output, press this button to select between the Optical #hand Coaxial $i Digital inputs. (See pages2628 for more information on digital audio.) Main Information Display: This displaydelivers messages and status indications tohelp you operate the receiver. (See pages 78for

49、a complete explanation of the InformationDisplay.) Channel Select Button: Press this buttonto begin the process of trimming the channeloutput levels using an external audio source.(For more information on output level trimadjustment, see page 29.) Speaker Select Button: Press this buttonto begin the

50、 process of selecting the speakerpositions that are used in your listening room.(See page 19 for more information on speakersetup and configuration.) Test Tone Selector: Press this button tobegin the process of adjusting the channel out-put levels using the internal test tone as a ref-erence. (For m