HarmanKardon-AVR320-avr-sm维修电路原理图.pdf

上传人:cc518 文档编号:147059 上传时间:2024-08-23 格式:PDF 页数:158 大小:13.97MB
下载 相关 举报
HarmanKardon-AVR320-avr-sm维修电路原理图.pdf_第1页
第1页 / 共158页
HarmanKardon-AVR320-avr-sm维修电路原理图.pdf_第2页
第2页 / 共158页
HarmanKardon-AVR320-avr-sm维修电路原理图.pdf_第3页
第3页 / 共158页
亲,该文档总共158页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《HarmanKardon-AVR320-avr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-AVR320-avr-sm维修电路原理图.pdf(158页珍藏版)》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR320 AVR320 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.10 REMOTE CONTROL FUNCTIONS.12 TROUBLESHOOTING GUIDE.15 PROCESSOR RESET.15 UNIT EXPLODED VIEW.16 EXPLODED VIEW PARTS LI

2、ST.17 BULLETIN H/K2002-03.19 BULLETIN H/K2002-07.20 BULLETIN H/K2003-07.21 TECH TIP HKTT2003-01.23 TECH TIP HKTT2004-03.24 IDLE CURRENT ADJUSTMENT.28 BLOCK DIAGRAM.31 ELECTRICAL PARTS LIST.32 SEMICONDUCTOR PINOUTS77 SCHEMATICS.136 WIRING DIAGRAM.157 PACKAGE.158harman/kardon, Inc. 250 Crossways Park

3、Dr. Woodbury, New York 11797 Rev5 6/2005 RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with, use only the replacement parts designat

4、ed, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyinsulated from the supply circuit before retuming the product to the custom

5、er.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors andsemiconductor chip components.The followin

6、g techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge onyour body by touching a known earth ground. Alternatively, obt

7、ain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil,

8、 toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical chargessufficient to dam

9、age ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacementES devices are packaged with leads

10、electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thechassis or circuit assembly into which the device will be installed

11、.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing togetheror your clothes fabric or the lifting of your foot from a carpeted floo

12、r can generate static electricity sufficient to damage an ES devices.CAUTION : AVR320 AVR320 harman/kardonharman/kardonRadioFans.CN 收音机爱 好者资料库21. Inspect all lead dress to make certain thatleads are not pinched or that hardware is notlodged between the chassis and other metalpartsintheunit.2. Be sur

13、e that any protective devices such asnonmetallic control knobs, insulating fish-papers,cabinetbacks,adjustmentandcompartment covers or shields, isolationresistor-capacitynetworks,mechanicalinsulators, etc. Which were removed for theservicingareproperlyre-installed.Before returning the unit to the us

14、er, perform the following safety checks :3. Be sure that no shock hazard exists ; check for leakagecurrentusingSimpsonModel229LeakageTester,standardequipment item No. 21641, RCA Model WT540A or usealternate method asfollows : Plug the power cord directlyInto a 120 volt AC receptacle (do not use an I

15、solationTransformer for this test). Using two clip leads, connect a1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,suchas a water pipe or conduit. Use a VTVM or VOM with 1000 ohms per volt, or higher sensitivity to measure the AC voltag

16、e drop across theresistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal,cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosstheresistor.(Thistestshouldbeperformedwiththe0.35voltRMSormore

17、isexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningtheunittotheowner. AVR320 AVR320 harman/kardonharman/kardon34 TECHNICAL SPECIFICATIONSTechnical SpecificationsAudio SectionStereo Mode Continuous Average Power (FTC)65 Watts per channel, 20Hz20kHz, 0.07% THD, both channel

18、s driven into 8 ohmsFive-Channel Surround Modes Power Per Individual ChannelFront L&R channels:55 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:55 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround channels:55 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsInput Sensitivity/Impedan

19、ceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)95dBSurround System Adjacent Channel SeparationAnalog Decoding 40dB(Pro Logic II, etc.)Dolby Digital55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz 100kHzHigh Instantaneous Current Capability (HCC)35 AmpsTransient Intermodulation Disto

20、rtion (TIM)UnmeasurableSlew Rate40V/secFM Tuner SectionFrequency Range87.5108MHzUsable SensitivityIHF 1.3 V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Rejection80dBIF Rejection90dBAM Tuner SectionFrequency Range

21、3201720kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance1Vp-p/75 ohmsVideo Frequency Response (Composite and S)10Hz8MHz (3dB)Video Frequency Response (Com

22、ponent) 10Hz30MHz (3dB)GeneralPower RequirementAC 120V/60HzPower Consumption72W idle, 580W maximum (2 channels driven)Dimensions (Max)Width17.3 inches (440mm)Height6.5 inches (165mm)Depth17.1 inches (435mm)Weight32 lb (14.5kg)Depth measurement includes knobs, buttons and terminal connections.Height

23、measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon is a registered trademark, and Power for the Digital Revolution is a trademark, of Harman Kardon, Inc.is a trademark of Harman International Industries, Inc. (Patent No. 5,386,478

24、).*Manufactured under license from Dolby Laboratories.“Dolby,”“Pro Logic,”“Pro Logic II” and the Double-D symbol aretrademarks of Dolby Laboratories. Confidential UnpublishedWorks. 19921999 Dolby Laboratories, Inc.All rights reserved.DTS, DTS Surround, DTS-ES and DTS Neo:6 are trademarks of Digital

25、Theater Systems, Inc.UltraStereo is a trademark of UltraStereo Corp.VMAx is a registered trademark of Harman International Industries, Inc., and is an implementation of Cooper Bauck Transaural Stereo under patent license.Logic 7 is a registered trademark of Lexicon, Inc.Crystal is a registered trade

26、mark of Cirrus Logic Corp.TM AVR320 AVR320 harman/kardonharman/kardon5 FRONT PANEL CONTROLS1 Main Power Switch: Press this button toapply power to the AVR 320.When the switchis pressed in, the unit is placed in a Standbymode, as indicated by the amber PowerIndicator 3 surrounding the SystemPower Con

27、trol 2.This button MUST bepressed in to operate the unit.To turn the unitoff and prevent the use of the remote control,this switch should be pressed until it pops outfrom the front panel so that the word “OFF”may be read at the top of the switch.NOTE: This switch is normally left in the “ON”position

28、.2 System Power Control: When the MainPower Switch 1 is “ON,” press this buttonto turn on the AVR 320; press it again to turnthe unit off. Note that the Power Indicator3 surrounding the switch will turn greenwhen the unit is on.3 Power Indicator: This LED will be lit inamber when the unit is in the

29、Standby mode tosignal that the unit is ready to be turned on.When the unit is in operation, the indicator willturn green.4 Headphone Jack:This jack may be used tolisten to the AVR 320s output through a pair ofheadphones. Be certain that the headphoneshave a standard 1/4 stereo phone plug. Notethat t

30、he main room speakers will automaticallybe turned off when the headphone jack is in use.5 Dolby Mode Selector: Pressing this selec-tor button cycles the AVR through the variousDolby surround modes.The first press of the but-ton switches the surround mode to the lastDolby surround mode that was in us

31、e. Each sub-sequent press selects the next mode in the fol-lowing order:6 DTS Surround Mode Selector: Pressingthis selector button cycles the AVR through theDTS surround modes.The first press of the but-ton selects the last DTS surround mode thatDOLBY 3 STEREODOLBY DIGITALDOLBY PRO LOGIC II MUSICDOL

32、BY PRO LOGIC II MOVIESDOLBY PRO LOGIC IIEMULATIONFront Panel Controls1 Main Power Switch2 System Power Control3 Power Indicator4 Headphone Jack5 Dolby Mode Selector6 DTS Surround Mode Selector7 Logic 7 Mode Selector /Button8 Tone Mode9 Surround Mode Selector) Tuning Selector! Tuner Band Selector Set

33、 Button# Preset Station Selector$ Stereo Mode Selector /Button% Input Source Selector FM Mode Selector& DTS Neo:6 Mode Selector* Digital Optical 3 Input( Input/Output Status Indicator Digital Coax 3 Jack Video 4 Input Jacks Bass Control Balance Control Treble Control Digital Select Button Channel Se

34、lect Button Volume Control Input Indicators Main Information Display Remote Sensor Window Surround Mode Indicators247913568)!#$%&*(1 Main Power Switch2 System Power Control3 Power Indicator4 Headphone Jack5 Dolby Mode Selector6 DTS Surround Mode Selector7 Logic 7 Mode Selector /Button8 Tone Mode9 Su

35、rround Mode Selector) Tuning Selector! Tuner Band Selector Set Button# Preset Station Selector$ Stereo Mode Selector /Button% Input Source Selector FM Mode Selector& DTS Neo:6 Mode Selector* Digital Optical 3 Input( Input/Output Status Indicator Digital Coax 3 Jack Video 4 Input Jacks Bass Control B

36、alance Control Treble Control Digital Select Button Channel Select Button Volume Control Input Indicators Main Information Display Remote Sensor Window Surround Mode Indicators AVR320 AVR320 harman/kardonharman/kardon6 FRONT PANEL CONTROLSFront Panel Controlswas in use. Each subsequent press selects

37、 thenext DTS mode in the following order:7 Logic 7 Mode Selector /Button: Thisbutton has two functions: In normal use, pressit to select one of the Logic 7 modes.When anadjustment is being made using the ChannelSelect or Digital Select buttons, thisbutton may be pressed to scroll through theavailabl

38、e options.8 Tone Mode: Pressing this button enablesor disables the Bass and Treble tone controls.When the button is pressed so that the wordsTONE IN appear in the Main InformationDisplay, the settings of the BassandTreblecontrols may be used to adjust theoutput signals.When the button is pressed sot

39、hat the words TONE OUT appear in the MainInformation Display, the output signalwill be “flat, ” without any bass or treble alter-ation, no matter how the actual Bass andTreble Controls are adjusted.9 Surround Mode Selector: Press this but-ton to change the surround mode by scrollingthrough the list

40、of available modes. Note thatdepending on the type of input, some modesare not always available. (See page 26 for moreinformation about surround modes.) Tuning Selector: Press the left side of thebutton to tune lower-frequency stations and theright side of the button to tune higher-frequencystations

41、.When a station with a strong signal is reached, the TUNED Indicator W will be litin the Main Information Display .To tune manually, tap the button lightly andnote that the tuner will step up one frequencyincrement per button press.When the button isheld for a few seconds you will note that theunit

42、will quickly search the frequency band.Release it once the fast tuning starts; the tunerwill automatically scan for the next station withan acceptable signal and then stop.! Tuner Band Selector: Pressing this but-ton will automatically switch the AVR 320 tothe Tuner mode. Pressing it again will swit

43、chbetween the AM and FM frequency bands. (Seepage 31 for more information on the tuner.) Set Button:When making choices duringthe setup and configuration process, press thisbutton to enter the desired setting as shown in the Main Information Display into the AVR 320s memory.# Preset Station Selector

44、: Press this button to scroll up or down through the list orstations that have been entered into the presetmemory. (See page 32 for more information ontuner programming.)$ Stereo Mode Selector /Button:Pressing this selector button cycles through the stereo modes, and it is also used to turn offall s

45、urround processing and place the unit in atraditional two-channel Stereo mode.The firstpress selects 5-Channel Stereo, the next pressselects 8-Channel Stereo, and the third pressselects “SURROUND OFF,” which is true Stereo.When an adjustment is being made using theChannel Select or Digital Select bu

46、ttons, this button may be pressed to scrollthrough the available options.% Input Source Selector: Press this buttonto change the input by scrolling up or downthrough the list of input sources. FM Mode Selector: Press this button toselect Auto or Manual tuning.When the buttonis pressed so that the AU

47、TO Indicator Xlights, the tuner will search for the next stationwith an acceptable signal when the TuningSelector )uis pressed.When the but-ton is pressed so that the AUTO Indicator Xis not lit, each press of the Tuning Selector)uwill increase the frequency. (Seepage 31 for more information on using

48、 thetuner.)& DTS Neo:6 Mode Selector: Pressing thisselector button cycles the AVR through the vari-ous DTS Neo:6 modes, which extract a five-channel surround field from two-channel pro-gram material.The first press selects the lastDTS Neo:6 surround mode that was in use, andeach subsequent press sel

49、ects the next mode inthe following order:* Digital Optical 3 Input: Connect the opti-cal digital output of an audio or video product tothis jack.When the input is not in use, be certainto keep the plastic cap installed to avoid dustcontamination that might degrade future performance.( Input/Output S

50、tatus Indicator:This LEDindicator will normally light green to show thatthe front panel Digital Coax 3jack is oper-ating as an input.When this jack is configuredfor use as an output, the indicator will turn redto show that the jack may be used for recording.(See page 20 for more information on confi

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 功放/音响/收扩 > HarmanKardon

copyright@ 2008-2025 收音机爱好者资料库 版权所有
备案编号:鄂ICP备16009402-5号