HarmanKardon-AVR510-avr-sm维修电路原理图.pdf

上传人:cc518 文档编号:147101 上传时间:2024-08-23 格式:PDF 页数:132 大小:16.30MB
下载 相关 举报
HarmanKardon-AVR510-avr-sm维修电路原理图.pdf_第1页
第1页 / 共132页
HarmanKardon-AVR510-avr-sm维修电路原理图.pdf_第2页
第2页 / 共132页
HarmanKardon-AVR510-avr-sm维修电路原理图.pdf_第3页
第3页 / 共132页
亲,该文档总共132页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《HarmanKardon-AVR510-avr-sm维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《HarmanKardon-AVR510-avr-sm维修电路原理图.pdf(132页珍藏版)》请在收音机爱好者资料库上搜索。

1、 harman/kardon AVR510 AVR510 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 FRONT PANEL CONTROLS.5 REAR PANEL CONNECTIONS.9 REMOTE CONTROL FUNCTIONS.11 TROUBLESHOOTING GUIDE.14 PROCESSOR RESET.14 IDLE CURRENT/TUNER ALIGNMENT.15 UNIT EXPLODED

2、 VIEW.16 EXPLODED VIEW PARTS LIST.17 SERVICE BULLETIN HK2001-01.18 SERVICE BULLETIN HK2001-03.20 SERVICE BULLETIN HK2003-02.21 SERVICE BULLETIN HK2003-07.22 TECH TIP HKTT2002-01.24 TECH TIP HKTT2003-01.26 BLOCK DIAGRAMS.27 PCB DRAWINGS.29 ELECTRICAL PARTS LIST.41 SEMICONDUCTOR PINOUTS.62 SCHEMATICS.

3、111 WIRING DIAGRAM.129 PACKAGE.132 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev4 6/2005 RadioFans.CN 收音机爱 好者资料库Eachprecautioninthismanualshouldbefollowedduringservicing.Components identified with the IEC symbolin the parts list are special significance to safety. When repl

4、acing a component identified with, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in theparts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptablyi

5、nsulated from the supply circuit before retuming the product to the customer.Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and s

6、ome field effect transistors andsemiconductor chip components.The following techniques should be used to help reduce the incidence of component damage caused by static electricity.1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostat

7、ic charge onyour body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES

8、devices, place the assembly on a conductive surface such as aluminum foil, toprevent electrostatic charge build-up or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not

9、classified as anti-static can generate electrical chargessufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are

10、 ready to install it. (Most replacementES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

11、 to thechassis or circuit assembly into which the device will be installed.Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing toget

12、heror your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.CAUTION :AVR510 AVR510 harman/kardon 2RadioFans.CN 收音机爱 好者资料库1. Inspect all lead dress to make certain thatleads are not pinched or that hardware is notlodge

13、d between the chassis and other metalpartsintheunit.2. Be sure that any protective devices such asnonmetallic control knobs, insulating fish-papers,cabinetbacks,adjustmentandcompartment covers or shields, isolationresistor-capacitynetworks,mechanicalinsulators, etc. Which were removed for theservici

14、ngareproperlyre-installed.Before returning the unit to the user, perform the following safety checks :3. Be sure that no shock hazard exists ; check for leakagecurrentusingSimpsonModel229LeakageTester,standardequipment item No. 21641, RCA Model WT540A or usealternate method asfollows : Plug the powe

15、r cord directlyInto a 120 volt AC receptacle (do not use an IsolationTransformer for this test). Using two clip leads, connect a1500ohms,10wattResistorparalleledbya0.15uFcapacitor,inserieswithallexposedmetalcabinetpartsandaknownearthground,suchas a water pipe or conduit. Use a VTVM or VOM with 1000

16、ohms per volt, or higher sensitivity to measure the AC voltage drop across theresistor. (See diagram) Move the resistor connection to each exposed metal part having a return path to the chassis (antenna, metal,cabinet,screwheads,knobsandcontrolshafts,escutcheon,etc.)andmeasuretheACvoltagedropacrosst

17、heresistor.(Thistestshouldbeperformedwiththe0.35voltRMSormoreisexcessiveandindicatesapotentialshockhazardwhichmustbecorrectedbeforereturningtheunittotheowner.AVR510 AVR510 harman/kardon 34 SPECIFICATIONSTechnical SpecificationsAudio SectionStereo Mode Continuous Average Power (FTC)80 Watts per chann

18、el, 20Hz20kHz, 0.07% THD, both channels driven into 8 ohmsFive-Channel Surround Modes Power Per Individual ChannelFront L&R channels:70 Watts per channel 0.07% THD, 20Hz20kHz into 8 ohmsCenter channel:70 Watts 0.07% THD, 20Hz20kHz into 8 ohmsSurround channels:70 Watts per channel 0.07% THD, 20Hz20kH

19、z into 8 ohmsInput Sensitivity/ImpedanceLinear (High-Level)200mV/47k ohmsSignal-to-Noise Ratio (IHF-A)95dBSurround System Adjacent Channel SeparationAnalog Decoding 40dB(Pro Logic, etc.)Dolby Digital (AC-3)55dBDTS55dBFrequency Response 1W (+0dB, 3dB)10Hz 100kHzHigh Instantaneous Current Capability (

20、HCC)35 AmpsTransient Intermodulation Distortion (TIM)UnmeasurableRise Time16secSlew Rate40V/secFM Tuner SectionFrequency Range87.5108MHzUsable SensitivityIHF 1.3 V/13.2dBfSignal-to-Noise RatioMono/Stereo 70/68dBDistortionMono/Stereo 0.2/0.3%Stereo Separation40dB 1kHzSelectivity400kHz, 70dBImage Reje

21、ction80dBIF Rejection90dBTuner Output Level1kHz, 75kHz Dev 500mVAM Tuner SectionFrequency Range5201710kHzSignal-to-Noise Ratio45dBUsable SensitivityLoop 500VDistortion1kHz, 50% Mod 0.8%Selectivity10kHz, 30dBVideo SectionTelevision FormatNTSCInput Level/Impedance1Vp-p/75 ohmsOutput Level/Impedance 1V

22、p-p/75 ohmsVideo Frequency Response10Hz8MHz (3dB)GeneralPower RequirementAC 120V/60HzPower Consumption78W idle, 694W maximum (2 channels driven)Dimensions (Max)Width17.3 inches (440mm)Height6.5 inches (165mm)Depth17.1 inches (435mm)Weight35 lb (15.9 kg)Depth measurement includes knobs, buttons and t

23、erminal connections.Height measurement includes feet and chassis.All features and specifications are subject to change without notice.Harman Kardon is a registered trademark, and Power for the Digital Revolution is a trademark, of Harman Kardon, Inc.is a trademark of Harman International Industries,

24、 Inc. (Patent No. 5,386,478).*Manufactured under license from Dolby Laboratories.“Dolby,”“Pro Logic,”“AC-3” and the Double-D symbol aretrademarks of Dolby Laboratories. Confidential UnpublishedWorks. 19921999 Dolby Laboratories, Inc.All rights reserved.DTS and DTS Surround are trademarks of Digital

25、Theater Systems, Inc.UltraStereo is a trademark of UltraStereo Corp.VMAx is a registered trademark of Harman International Industries, Inc., and is an implementation of Cooper Bauck Transaural Stereo under patent license.Logic 7 is a registered trademark of Lexicon, Inc.Crystal is a registered trade

26、mark of Cirrus Logic Corp.HDCD system manufactured under license from Pacific Microsonics, Inc.This product is covered by one or more of the following: In the USA: 5,479,168; 5,638,074; 5,640,161; 5,808,574;5,838,274; 5,854,600; 5,864,311; 5,872,531; and in Australia: 669114. Other patents pending.T

27、MAVR510 AVR510 harman/kardon 5 FRONT PANEL CONTROLS1 Main Power Switch: Press this button toapply power to the AVR 510.When the switchis pressed in, the unit is placed in a Standbymode, as indicated by the amber PowerIndicator 3 surrounding the SystemPower Control 2.This button MUST bepressed in to

28、operate the unit.To turn the unitoff and prevent the use of the remote control,this switch should be pressed until it pops outfrom the front panel so that the word “OFF”may be read at the top of the switch.NOTE: This switch is normally left in the “ON”position.2 System Power Control: When the MainPo

29、wer Switch 1 is “ON,” press this buttonto turn on the AVR 510; press it again to turnthe unit off. Note that the Power Indicator3 surrounding the switch will turn greenwhen the unit is on.3 Power Indicator: This LED will be lit inamber when the unit is in the Standby mode tosignal that the unit is r

30、eady to be turned on.When the unit is in operation, the indicator willturn green.4 Headphone Jack:This jack may be used tolisten to the AVR 510s output through a pair ofheadphones. Be certain that the headphoneshave a standard 1/4 stereo phone plug. Notethat the main room speakers will automatically

31、be turned off when the headphone jack is in use.5 Selector Buttons:When you are establish-ing the AVR 510s configuration settings,usethese buttons to select from the choices available,as shown in the Main Information Display or the on-screen displays.6 Tone Mode: Pressing this button enablesor disab

32、les the Bass and Treble tone controls.When the button is pressed so that the wordsTONE IN appear in the Main InformationDisplay , the settings of the Bass & andTreble ( controls may be used to adjust theoutput signals.When the button is pressed sothat the words TONE OUT appear in the MainInformation

33、 Display , the output signalwill be “flat, ” without any bass or treble alter-ation, no matter how the actual Bass andTreble controls &( are adjusted.Front Panel Controls1 Main Power Switch2 System Power Control3 Power Indicator4 Headphone Jack5 Selector Buttons6 Tone Mode7 Surround Mode Selector8 T

34、uning Selector9 Tuner Band Selector) Preset Stations Selector! Input Source Selector FM Mode Selector# Digital Optical 3 Input$ Input/Output Status Indicator% Digital Coax 3 Jack Video 4 Input Jacks& Bass Control* Balance Control( Treble Control Volume Control Set Button Input Indicators Delay Digit

35、al Input Selector Main Information Display Channel Select Button Speaker Select Button Test Tone Selector Surround Mode Indicators Remote Sensor Window?&?&?*&(? ?333111444 555666777888999)!# %2930?$222COAXIALTHEATER5 CH STEREO HALL 123-STEREOPRO LOGICDIGITALNIGHTMULTIOPTICALANALOGOSDLFE0CL0123123MEM

36、ORYPRESETSLEEPAUTO5.1 LOGIC 7 CMVMAx NFMUTETUNEDSTOOROOLSOORSOODTSDOLBY DPCMMP3AVR510 AVR510 harman/kardon 6 FRONT PANEL CONTROLSFront Panel Controls7 Surround Mode Selector: Press this but-ton to change the surround mode by scrollingthrough the list of available modes. Note thatdepending on the typ

37、e of input, some modesare not always available. (See page 27 for moreinformation about surround modes.)8 Tuning Selector: Press the left side of thebutton to tune lower-frequency stations and theright side of the button to tune higher-frequencystations.When a station with a strong signal is reached,

38、 the TUNED indicator W will be litin the Main Information Display .To tune manually, tap the button lightly andnote that the tuner will step up one frequencyincrement per button press.When the button isheld for a few seconds you will note that theunit will quickly search the frequency band.Release i

39、t once the fast tuning starts; the tunerwill automatically scan for the next station withan acceptable signal and then stop.9 Tuner Band Selector: Pressing this buttonwill automatically switch the AVR 510 to theTuner mode. Pressing it again will switchbetween the AM and FM frequency bands. (Seepage

40、30 for more information on the tuner.) Preset Stations Selector: Press this button to scroll up or down through the list orstations that have been entered into the presetmemory. (See page 30 for more information ontuner programming.)! Input Source Selector: Press this buttonto change the input by sc

41、rolling up or downthrough the list of input sources. FM Mode Selector: Press this button toselect Auto or Manual tuning.When the buttonis pressed so that the AUTO indicator X lights,the tuner will search for the next station with anacceptable signal when the Tuning Selector8uis pressed.When the butt

42、on ispressed so that the AUTO indicator X is not lit,each press of the Tuning Selector 8uwill increase the frequency. (See page 30 formore information on using the tuner.)# Digital Optical 3 Input: Connect the opti-cal digital output of an audio or video product tothis jack.When the input is not in

43、use, be certainto keep the plastic cap installed to avoid dustcontamination that might degrade future performance.$ Input/Output Status Indicator: TheseLED indicators will normally light green to showthat the front panel Video 4 A/V jacks or theCoaxial 3 digital jack is operating as an input.When ei

44、ther of these jacks has been configuredfor use as an output, the indicator will turn redto show that the jack may be used for recording.(See page 20 for more information on configur-ing the front panel jacks as outputs, rather thaninputs.)% Digital Coax 3 Jack: This jack is normallyused for connecti

45、on to the output of portableaudio devices, video game consoles or otherproducts that have a coax digital jack. It mayalso be configured as an output jack, to feed adigital signal to a CD-R, MiniDisc or other digi-tal recording device. (See page 31 for informa-tion on configuring the Digital Coax 3 J

46、ack toan output.) Video 4 Input Jacks: These audio/videojacks may be used for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio players.& Bass Control:Turn this control to modifythe low-frequency output of the left/right chan-nels by as much as

47、10dB.Set this control to asuitable position for your taste or room acoustics.* Balance Control: Turn this control tochange the relative volume for the frontleft/right channels.NOTE: For proper operation of the surroundmodes this control should be at the midpoint,or “12 oclock”, position.(Treble Cont

48、rol:Turn this control to modifythe high-frequency output of the left/right chan-nels by as much as 10dB.Set this control to asuitable position for your taste or room acoustics. Volume Control: Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR 510 is m

49、uted,adjusting volume control will automaticallyrelease the unit from the silenced condition. Set Button:When making choices duringthe setup and configuration process, press thisbutton to enter the desired setting as shown in the Main Information Display into the AVR 510s memory. Input Indicators: A

50、 green LED will light infront of the input that is currently being used asthe source for the AVR 510. Delay: Press this button to begin thesequence of steps required to enter delay timesettings. (See page 21 for more information ondelay times.) Digital Input Selector: When playing asource that has a

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 功放/音响/收扩 > HarmanKardon

copyright@ 2008-2025 收音机爱好者资料库 版权所有
备案编号:鄂ICP备16009402-5号