HarmanKardon-HKTS10-htss-sm维修电路原理图.pdf

《HarmanKardon-HKTS10-htss-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《HarmanKardon-HKTS10-htss-sm维修电路原理图.pdf（23页珍藏版）》请在收音机爱好者资料库上搜索。

1、harman/kardonHKTS 10Home Cinema Speaker SystemSERVICE MANUALharman/kardon, Inc.250 Crossways Park Dr.Woodbury, New York 11797Rev0 8/2002RadioFans.CN 收音机爱 好者资料库CONTENTSSPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1DETAI

2、LED SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2CONTROLS & CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3OPERATION & ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、. . . . . . . . . . . . . . . . . . . 8BASIC TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9SUB-TS10 TEST PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10SUB-TS10 BLOCK DIAGRAM . .

4、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11MECHANICAL/PACKING PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12SUB-TS10 EXPLODED VIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、. . . . . . 13SUB-TS10 PCB DRAWINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14SUB-TS10 IC TRANSISTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16SUB-TS10 ELECTRICAL PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . .

6、 . . . . . . . . . . 17SUB-TS10 SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20SPECIFICATIONSHKTS 10 System Frequency Response 35Hz 20kHz (6dB)SAT-TS10 SatellitesRecommended Power10 110 wattsImpedance8 ohms nominalSensitivity86dB 1 watt/1 me

7、terTweeterOne 1 dome, video-shieldedMidrangeOne 4 driver, video-shieldedDimensions (H x W x D)10-1/8 x 5-1/4 x 5-3/8257mm x 133mm x 137mmWeight6.6 lb/3.0kgCEN-TS10 CenterRecommended Power10 110 wattsImpedance8 ohms nominalSensitivity86dB 1 watt/1 meterTweeterOne 1 dome, video-shieldedMidrangeDual 4

8、drivers, video-shieldedDimensions (H x W x D)5-1/16 x 16-1/2 x 5-3/16128mm x 418mm x 131mmWeight10 lb/4.5kgSUB-TS10 SubwooferAmplifier150 watts RMSBass Driver12 woofer, bass-reflexenclosureDimensions (H x W x D)20-5/16 x 16-3/8 x 15-1/16515mm x 416mm x 382mmWeight40 lb/18.0kgOccasional refinements m

9、ay be made to existing products without notice but will always meet or exceed originalspecifications unless otherwise stated.RadioFans.CN 收音机爱 好者资料库1SUB-TS10150W Powered AmplifierLINE VOLTAGEYes/NoHi/Lo LineUnitNotesUS 120vac/60HzYes108-132VrmsNormal OperationParameterSpecificationUnitQA Test Limits

10、 ConditionsNotesAmp SectionType (Class AB, D, other)D D n/aLoad Impedance (speaker)4 Ohmsn/aNominalRated Output Power150 Watts1501 input drivenTHD Rated Power0.08 %122k filterTHD 1 Watt0.15 %0.522k filterDC Offset5 mV-DC30 Speaker OutputsDamping factor100 DF30Measured at speaker terminals, Output po

11、wer140 Watts THD 0.1 %Input SensitivityInput Frequency50 HzNANominal Freq.1 input drivenLine Input (L&R)220 mVrms2dBTo Rated Power1 input drivenLFE Input220 mVrms2dBTo Rated PowerLFE input driven onlySpeaker/Hi Level Input2.2 Vrms2dBTo Rated Power(-20 dB below Line In).1 input drivenSignal to NoiseS

12、NR-A-Weighted100 dBA85rel. to rated powerA-Weighting filterSNR-unweighted90 dBr80rel. to rated power22k filterSNR 1W-unweighted65 dBr60rel. to 1W Output22k filterResidual Noise Floor1.2 mVrms3.0Volume max, using RMS reading DMM/VOM (or A/P)Residual Noise Floor0.8mVrms(max)2.0Volume max, w/ A/P Swept

13、 Bandpass Measurement (Line freq.+ harmonics)Input ImpedanceLine input L&R , LFE10 K ohmsn/aNominalSpeaker/Hi Level Input4.7 K ohmsn/aNominalFiltersLeft & Right Low Pass fixed130 Hz-2dB -3dB ref. 100HzLFE Low Pass fixed220 Hz-2dB -3dB ref. 100HzSubsonic filter (HPF)22 Hz-2dB -3dB ref. 100HzLimiterYE

14、S-n/aFeaturesLFE InputYESfunctional BW Limited to 220 HzVolume pot Taper (lin/log)log-functional ATOYESfunctional Signal Sensing (ATO)ATO test Frequency50 Hzn/aATO Line Level4.0 mV2.0 - 8.02mV50Hz into Line Input w/ 1 ch. drivenATO Speaker level input40 mV20 - 8050mV50Hz into Line Input w/ 1 ch. dri

15、venATO Turn-on time5 msfunctionalAmp connected and AC on, then input signal appliedAuto Mute/ Turn-OFF Time15 minutes10 - 25T before muting, after signal is removedPower on Delay time3 sec.functionalAC Power AppliedTransients/PopsATO Transient5 mV-peak10 Speaker OutputsTurn-on Transient50 mV-peak100

16、 Speaker OutputsAC Line cycled from OFF to ONTurn-off Transient50 mV-peak100 Speaker OutputsAC Line cycled from ON to OFFEfficiencyStand-by Input Power10 Watts12 nom. line voltageMaximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation.Power Cons.rated power230

17、Watts250 nom. line voltage150 Watts 4 Ohms nominal line voltageProtectionShort Circuit Protection YES-functionalDirect short at outputThermal Protection 65 deg. C-functional1/8 max unclipped Power Temperature rise should not exceed 35K riseDC Offset ProtectionYES-functionalDC present at Speaker Out

18、leadsRelay or crowbar (for driver/fire protection)Line Fuse RatingUS Version3.15 AmpsType-T or Slo BloExternal fuse with UL/SEMKO rated holder HKTS 10harman/kardon2SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS Speaker-Level Inputs: Connect thesebinding post terminals to the main left a

19、ndright speaker terminals of your receiver oramplifier, if your receiver or amplifier doesnot have a line-level subwoofer output.Remember to maintain polarity by connectingthe (+) terminal on the receiver/amplifier tothe (+) terminal on the SUB-TS10 subwoofer,and the () terminal on the receiver/ampl

20、ifier tothe () terminal on the SUB-TS10 subwoofer. Speaker-Level Outputs: If you areusing the Speaker-Level Inputs on the SUB-TS10, you should connect thesebinding post terminals to your front left andright speakers, remembering to maintainpolarity by connecting the (+) terminal onthe SUB-TS10 subwo

21、ofer to the (+) termi-nal on the speaker, and the () terminal onthe SUB-TS10 subwoofer to the () terminalon the speaker. If you are not using theSpeaker-Level Inputs , then connectyour front left and right speakers directly toyour receiver or amplifier. See pages 6 and7 for further information. Line

22、-Level Subwoofer (SUB) Input:Connect the subwoofer output of a receiverwith digital surround sound decoding, suchas Dolby* Digital or DTS, to this input.Thisinput bypasses the SUB-TS10s internalcrossover circuitry, and should only be usedwith a filtered signal. If your receiver doesnot have digital

23、decoding,you should use theLine-Level Full-Range Inputs instead. Line-Level Full-Range Inputs: Con-nect the line-level subwoofer output or preamp output(s) of your receiver or amplifierto these inputs.If your receiver does not havea separate subwoofer output,use a Y-adaptor(not supplied) to bridge t

24、he receivers preampoutput to the main amp input for that chan-nel,and connect the long end of the adaptorto the corresponding line-level input on theSUB-TS10.If your receiver has only a singlesubwoofer output,you may connect it toeither the left or right line-level input on theSUB-TS10,and no Y-adap

25、tor is needed. Phase Switch: This switch determineswhether the SUB-TS10 subwoofers piston-RISK OF ELECTRIC SHOCK DO NOT OPENCAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENCAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENharman/kardonSUB-TS10For use withHKTS 10 SystemOFFNORMALREVERSEOOFER LEVELONAUTOIMPORTANT: CON

26、NECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.AC 120V60HzPOWERMade in ChinaLRSUBPHASEFILTERCONTROLSUBWGREEN: ONRED: STAND-BYFILTERREMOTELINELEVELINONLR Speaker-Level Inputs Speaker-Level Outputs Line-Level Subwoofer (SUB) Input Line-Level Full-Range Inputs Phase Switch High-Cut (Low-Pass) Filter Swi

27、tch Music-Sense On/Off Switch Filter Remote Control Input LED Indicator Subwoofer-Level Control Master Power Switch AC Power Cord3 HKTS 10 harman/kardonSUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONSlike action moves in and out in phase withthe main speakers. If the speakers were toplay

28、out of phase, the sound waves pro-duced by the subwoofer would be cancelledout, reducing bass response.This phenome-non depends in part on the relative place-ment of the speakers in the room. In mostcases, the Phase Switch should be leftin the NORMAL position. However, itdoes no harm to experiment w

29、ith thePhase Switch , and you may leave it in the position that maximizes bassresponse. High-Cut (Low-Pass) Filter Switch:Placing this switch in the ON position acti-vates circuitry that cuts out all audio inputsignals above 120Hz.This allows the SUB-TS10 to focus its power on reproducing thelow-fre

30、quency portion of the signal, avoid-ing inefficiency and distortion. Engage thisfilter when using the Speaker-LevelInputs , or when using the Line-LevelFull-Range Inputs , unless your receiveror processor processes its line-level outputusing a low-pass filter.The filter has noeffect when the SUB Inp

31、ut is used. Music-Sense On/Off Switch:Whenplaced in the AUTO position,and when theMaster Power Switch is turned on,theSUB-TS10 will automatically turn itself on orplace itself in the Standby mode,dependingon whether it is receiving an audio signal.When this switch is placed in the ON posi-tion,the S

32、UB-TS10 will remain on,whether ornot it is receiving an audio signal. Filter Remote Control Input: Thisinput accepts a remote control signal froma compatible Harman Kardon A/V receiverthat enables you to override the High-Cut(Low-Pass) Filter Switch , by signal-ing the SUB-TS10 to engage the filter

33、evenwhen the switch is in the OFF position. LED Indicator: This LED indicateswhether the SUB-TS10 is in the ON orSTANDBY state when used with theMusic-Sense On/Off Switch in theAUTO position.The LED is lit Green toindicate that the SUB-TS10 is receiving an audio signal and is turned on, and theLED i

34、s lit Red to indicate that no signal isbeing received and the SUB-TS10 is inStandby mode.When the Music-Sense On/Off Switch is in the ON position, the LED will be litGreen, whether or not an audio signal ispresent.When the Master Power Switch isturned off, the LED goes dark, no matterwhich position

35、the Music-Sense On/OffSwitch is in. Subwoofer-Level Control: Volumecan be adjusted using the Subwoofer-Level Control.Turn the control clockwiseto increase the SUB-TS10s volume, orcounterclockwise to decrease it. Master Power Switch: Place thisswitch in the “” position to power-on theSUB-TS10 subwoof

36、er.The SUB-TS10 willthen be either in the Standby mode or completely on, depending on the positionof the Music-Sense On/Off Switch . AC Power Cord: Make sure to plugthis cord into an active, unswitched electri-cal outlet for proper operation of the SUB-TS10.The cord should not be plugged intothe acc

37、essory outlets found on some audiocomponents.4 HKTS 10 harman/kardonDolby Digital or DTS (or otherDigital Surround Mode)ConnectionUSE THIS INSTALLATION METHOD FORDOLBY DIGITAL, DTS OR OTHER DIGITALSURROUND PROCESSORS:Use the line-level input jack marked SUB for the Low-Frequency Effects channel.Conn

38、ect this jack to the subwoofer outputor LFE output on your receiver or amplifier.Connect each speaker to the correspondingspeaker terminals on your receiver or amplifier.Make sure that you have configured yoursurround sound processor for “SubwooferOn. ” The front left, front right, center andrear su

39、rround speakers should all be set to“Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.LINELEVELINLRSUBReceiverSUB/LFE OutFrontLeftSurroundLeftFrontRightSurroundRightCenterSurroundRightFrontRightSurroundLeftFrontLeftCenter + + + + +SPEAKER CONNECTIO

40、NS (continued)5 HKTS 10 harman/kardonSPEAKER CONNECTIONS (continued)6ReceiverSUB/LFE OutFrontLeftSurroundLeftFrontRightSurroundRightSUB-TS10SubwooferCenterLine-LevelLRSurroundRightFrontRightSurroundLeftFrontLeftCenter + + + + +Dolby Pro Logic (Non-Digital) Line LevelUSE THIS INSTALLATION METHOD FORD

41、OLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR IS EQUIPPED WITH A SUB-WOOFER OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Use the supplied RCA-type patch cord toconnect the line-level subwoofer output onyour receiveror amplif

42、ier to either the left orright Line-Level Full-Range Input onthe SUB-TS10 subwoofer. Use both the leftand right inputs on the subwoofer if yourreceiver or processor has both left and rightline-level outputs.If your receiver is equipped with line-leveloutputs but does not have a separate sub-woofer o

43、utput,use a Y-adaptor (not supplied)to bridge the receivers preamp output to themain amp input for that channel,and connectthe long end of the adaptor to the corre-sponding line-level input on the SUB-TS10.IMPORTANT: Do not use the SUB Input on the subwoofer with Dolby Pro Logicprocessors. Make sure

44、 that you have config-ured your surround sound processor for“Subwoofer On. ” The front left, front right,center and rear surround speakers shouldall be set to “Small. ”When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet.Connect each speaker to the correspondi

45、ngspeaker terminals on your receiver or amplifier. HKTS 10 harman/kardon7Front RightFront LeftSurround LeftSurround RightCenterFront LeftSurround LeftCenterFront RightSurround RightReceiver + + + + +SUB-TS10SubwooferLRSPEAKER CONNECTIONS (continued)Dolby Pro Logic* (Non-Digital) Speaker LevelUSE THI

46、S INSTALLATION METHOD FORDOLBY PRO LOGIC APPLICATIONS (NOTDOLBY DIGITAL, DTS OR OTHER DIGITALPROCESSING),WHERE THE RECEIVER/PROCESSOR DOES NOT HAVE A SUB-WOOFER OUTPUT, OR A VOLUME-CONTROLLED PREAMP (LINE-) LEVEL OUTPUT:Connect your receiver or amplifiers frontleft and right speaker terminals to the

47、 left and right Speaker-Level Input terminals on the SUB-TS10 subwoofer thatare marked “High Level In.” Connect the left and right Speaker-Level Output terminals on the SUB-TS10 subwoofer that are marked “High Level Out” to thecorresponding terminals on the back of your front left and right speakers

48、.Connect your receiver or amplifiers center,and surround left and right speaker terminals to the corresponding terminals on the back of your center, and surroundleft and right speakers.When all connections have been made, plugthe AC power cord on the subwoofer intoan AC outlet. HKTS 10 harman/kardon

49、8OPERATION Move the Master Power Switch (marked Power) to the “” (On) position.The SUB-TS10 subwoofer will automaticallyturn itself on or go into Standby mode,depending on whether or not a signal isbeing sent to it by your receiver or surroundprocessor, and provided that the Music-Sense On/Off Switc

50、h is moved to theright so that it is in the AUTO position.When your receiver or amplifier is off, or isnot sending program material to the sub-woofer, the subwoofer will be in Standbymode and the LED Indicator on theamp panel will turn red.When the sub-woofer senses an audio signal,it will auto-mati