Marantz-PM15S1-int-sm2 维修电路原理图.pdf

《Marantz-PM15S1-int-sm2 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Marantz-PM15S1-int-sm2 维修电路原理图.pdf（51页珍藏版）》请在收音机爱好者资料库上搜索。

1、PM-15S1Please use this service manual with referring to the user guide ( D.F.U. ) without fail.ServiceManualPM-15S1PM-15S1Integrated AmplifierPM-15S1 /F N/K1G/L1G/N1G/S1G/N1SPart no. 90M10AJ855010First Issue 2005.03MJITABLE OF CONTENTSSECTION PAGE 1. TECH NI CAL SPEC I FI CA TIONS . 1 2. CAUTION. 1

2、3. ALIGNMENTS. 2 4. SERVICE MODE. 3 5. MAIN MICROPROCESSOR (QU01) UPDATE PROCEDURE. 5 6. WIRING DIAGRAM . 19 7. BLOCK DIAGRAM . 21 8. SCHEMATIC DIAGRAM. 23 9. PARTS LOCATION. 2910. IC DATA. 3811. EXPLODED VIEW AND PARTS LIST. 4312. ELECTRICAL PARTS LIST. 47RadioFans.CN 收音机爱 好者资料库MARANTZ DESIGN AND S

3、ERVICEUsing superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound.Only original MARANTZ parts can insure that your MARANTZ product will continue to perform to the specifi cations for which it is famous. Parts for your MARANTZ equipment are gener

4、ally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax. In both cases, the correct part number has to be specifi ed. The following information must be supplied to eliminate delays in processing your order : 1. Complete address 2. Co

5、mplete part numbers and quantities required 3. Description of parts 4. Model number for which part is required 5. Way of shipment 6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void.SHOCK, FIRE HAZARD SERVICE TEST : CAUTION : After serv

6、icing this appliance and prior to returning to customer, measure the resistance between either primary AC cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and controls and chassis bottom. Any resistance measurement less than

7、1 Megohms should cause unit to be repaired or corrected before AC power is applied, and verifi ed before it is return to the user/customer. In case of diffi culties, do not hesitate to contact the Technical Department at above mentioned address. 050224MJIUSAMARANTZ AMERICA, INC1100 MAPLEWOOD DRIVEIT

8、ASCA, IL. 60143USAPHONE : 630 - 741 - 0300FAX : 630 - 741 - 0301JAPANTechnical MARANTZ JAPAN, INC.35- 1, 7- CHOME, SAGAMIONOSAGAMIHARA - SHI, KANAGAWAJAPAN 228-8505PHONE : +81 42 748 1013FAX : +81 42 741 9190EUROPE / TRADING MARANTZ EUROPE B.V.P. O. BOX 8744, BUILDING SILVERPOINTBEEMDSTRAAT 11, 5653

9、 MA EINDHOVENTHE NETHERLANDSPHONE : +31 - 40 - 2507844FAX : +31 - 40 - 2507860AUSTRALIAQualiFi Pty Ltd,24 LIONEL ROAD, MT. WAVERLEY VIC 3149AUSTRALIAPHONE : +61 - (0)3 - 9543 - 1522FAX : +61 - (0)3 - 9543 - 3677NEW ZEALANDWILDASH AUDIO SYSTEMS NZ14 MALVERN ROAD MT ALBERTAUCKLAND NEW ZEALANDPHONE : +

10、64 - 9 - 8451958FAX : +64 - 9 - 8463554THAILANDMRZ STANDARD CO., LTD746 - 754 MAHACHAI ROAD.,WANGBURAPAPIROM, PHRANAKORN, BANGKOK, 10200 THAILANDPHONE : +66 - 2 - 222 9181FAX : +66 - 2 - 224 6795TAIWANPAI- YUING CO., LTD.6 TH FL NO, 148 SUNG KIANG ROAD, TAIPEI, 10429, TAIWAN R.O.C.PHONE : +886 - 2 -

11、 25221304FAX : +886 - 2 - 25630415MALAYSIAWO KEE HONG ELECTRONICS SDN. BHD.2ND FLOOR BANGUNAN INFINITE CENTRELOT 1, JALAN 13/6, 46200 PETALING JAYASELANGOR DARUL EHSAN, MALAYSIAPHONE : +60 - 3 - 7954 8088FAX : +60 - 3 - 7954 7088CHINAMARANTZ SHANGHAI TRADING LTD.ROOM.506 SHANGHAI LIGHT INDUSTRY MANS

12、ION1578 NANJING (WEST) ROAD SHANGHAICHINATEL: 021 - 6248 - 1064FAX : 021 - 6248 - 3565KOREAMK ENTERPRISES LTD.ROOM 604/605, ELECTRO-OFFICETEL, 16-58, 3GA, HANGANG-RO, YONGSAN-KU, SEOULKOREAPHONE : +822 - 3232 - 155FAX : +822 - 3232 - 154SINGAPOREWO KEE HONG DISTRIBUTION PTE LTDNo.1 JALAN KILANG TIMO

13、R#08-03 PACIFIC TECH CENTRE SINGAPORE 159303PHONE : +65 6376 0338FAX : +65 6376 0166CANADAMARANTZ CANADA INC.5-505 APPLE CREEK BLVD. MARKHAM, ONTARIO L3R 5B1CANADAPHONE : 905 - 415 - 9292FAX : 905 - 475 - 4159RadioFans.CN 收音机爱 好者资料库11. TECHNICAL SPECIFICATIONSPower output (20 Hz 20 kHz simultaneous

14、drive of both channels) . 90W x 2 (8 load) . 140W x 2 (4 load)Total harmonic distortion (20Hz 20kHz simultaneous drive of both channels, 8 load) .0.05%Power band width (8 load, 0.05%).5Hz 40kHzFrequency response (CD, 1W, 8 load.5Hz 100kHzDumping factor (8 load, 20Hz 20kHz). 100Input sensitivity/Inpu

15、t impedance PHONO (MC). 300V/100 PHONO (MM). 3.2mV/47k CD/LINE/RECORDER . 240mV/20kOutput voltage/Output impedance PRE OUT. 1.7 V/330Maximum allowed PHONO input (1kHz) MC .15mV MM.150mV RIAA deviation (20Hz 20kHz) .0.5dBS/N (IHF-A, 1W, 8 load) PHONO (MC). 77dB (0.5mV input) PHONO (MM). 85dB (5mV inp

16、ut) CD/LINE/RECORDER . 90dB (500mV input)Tone control Bass (50Hz) .10dB Treble (20kHz).10dBPower requirement .AC 100V 50/60Hz /F . AC 220V 50/60Hz /K .AC 110V 60Hz /L .AC 230V 50Hz /N/SPower consumption (EN60065).220W (4 , 140W x 2 output).550WAccessories Remote controller. 1 AAA batteries. 2 Detach

17、able AC power cable. 1Maximum outer dimensions (Amp) Width. 440mm Height. 123mm Depth . 444mmWeight (Amp).18.0kg4194312344025182. CAUTIONThe layout of this amplifi er is well concerned for sound quality.1. When screws and washers are removed, those parts must be set to the same places.2. When wires

18、are removed, the wires must be installed in the same roots, same places.3. Do not hold the side panel (007D) to move the unit when the unit is disassembled.2.?1. ?2. ?3. ?(007D)?2P701P601R723J709R623 J609Digital VoltmeterR chVDigital VoltmeterL chV3. ALIGNMENTSIdling Current Adjustment1. Adjust the

19、Idling Current with the variable resistor R623 and R723 on the PCB (P601/P701).2. Turn off the power.3. - of Connect Digital Voltage is connected to the No. 1 pin and connected + to No. 3 pin of J609.4. - of Connect Digital Voltage is connected to the No. 1 pin and connected + to No. 3 pin of J709.5

20、. Before turning on the power, R623 and R723 have been counter clockwise turned with the adjustment driver.6. Turn on the power, VOLUME is set as - .7. With seeing the digital voltage meter turn the variable resister clockwise slowly to adjust the idling current.Idling adjustment with R623 (R723). T

21、urn R623 (R723) clockwise to increase the idling cur-rent. The adjustment value of idling current is 10mV(50mA) 0.5mV(2.5mA) each.8. After 4 minutes, repeat the same procedure as 7. Turn R623 (R723) clockwise to increase the idling current. The adjustment value of idling current is 10mV(50mA) 0.5mV(

22、2.5mA) each. Adjustment is completed.9. Remove connection cable, attach the top cover.?1. P601/P701?R623?R723?2. ?OFF?3. P601?J609?J609?1?-?3?+?4. P701?J709?J709?1?-?3?+?5. ?R623?R723?6. ?-?7. P601?J609?R623? R623 ? R723 ? ? 10mV(50mA) 0.5mV(2.5mA) ?8. ?4? ?7.? ?9. ?3?This is an exampleDISPLAY butto

23、nDISPLAYATT buttonPOWER ON/OFF button4. SERVICE MODE1. To enter the Service Mode, press the POWER ON/OFF button with pressing the DISPLAY and ATT buttons to turn on the unit. (Or when the remote code 166363 is received while power is ON.) When into the Service Mode, the memory is cleared and the uni

24、t is initialized. 2. The Model name and Version number are displayed on the Front LCD. Whenever press the DISPLAY button, the display changes as follows. Turn off power to quit service mode. THE TRIM CHECK MODE1. Press TONE button. (1 st) Volume Level is displayed . After, whenever press the TONE bu

25、tton, TRIM adjust-ment function works and output level changes accord-ing to the display. Whenever press the TONE button, the display chang-es as follows and output level changes according to the display. TRIM check mode is completed.1. ?DISPLAY?ATT?POW ER ON/OFF? ?ON?166363? ?2. ? DISPLAY? POWER ON

26、/OFF?TRIMTRIM?1.TONE ? ?1?TONE ?TONE ?TRIM?4ID No.: 0 INPUT SELECTOR: CD VOLUME: - SIDE ILLUMINATION: ON DISPLAY: ON ATT: OFFLEVEL TRIM: 0.0 (L/R) TONE: OFF SPEAKER : OFFATT: -20dB REC OUT: OFF PHONO MC:OFF ? ?1 ERROR 02 ID ? 2 ?2 ERROR 03 ID ? 3 ?3 ERROR 04 ID ? 4 ?4 ERROR 11 ID ? 2 ? 4 ? ID ? 1 ?5

27、 ERROR 12 ID ? 1 ? ID ? 2 ? 4 ? ?ID ?ID ? ID ? 1 ? ? ID ? 1 ? ID ? ?ERROR MESSAGES Error Contents1 ERROR 02 The units of ID No.2 overlaps.2 ERROR 03 The unit of ID No.3 over laps.3 ERROR 04 The unit of ID No.4 overlaps.4 ERROR 11 The unit of ID No.2 to No.4 cannot com- mu ni cate with the unit of ID

28、 No.1.5 ERROR 12 The unit of ID No.1 cannot com mu -ni cate with the unit of ID No.2 to No.4 MeasureID number is changed into the ID No. not over- lap ping.If the unit ID number 1 is not turn on, turn on the unit ID No.1.Check the remote cable is connected correctly.ID No. is changed into ID No. not

29、 overlapping. Check the remote cable is connected correctly.?2. Press DISPLAY button, the display will be the following.3. Press DISPLAY button, the display will be the following.4. Turn off power to quit service mode. Service mode can be ended if turn off power from every procedure. The memory is c

30、leared and the unit is initialized.Initial settings Be sure to set up manually. MODE SW on Rear panel: STEREO POWER ON/OFF SW: OFF2.DISPLAY ?3.DISPLAY ?4.POWER ON/OFF? ? ? ?5? ? Windows PC (OS:Windows2000 ?WindowsXP) ?COM port? ? RS232C? (9pin?- 9pin?) ? ? (90M-PM15S1CDR) ? ? (? : 90M-PM11S1JIG)5.1.

31、 ?5.1. ?Necessary Equipment Windows PC (Windows2000 or WindowsXP) with COM port RS232C cable straight type (9pin female - 9Pin female) Update Disc (90M-PM15S1CDR) DATA UPDATE KIT (part no.: 90M-PM11S1JIG)5.1. ConnectionRS232C Dsub-9 pin cable (female to female/Straight cable)DATA UPDATE KIT(Parts No

32、. 90M-PM11S1JIG) PC (Windows 2000, XP ) with RS-232C port INSERT POINTContact is the bottom5. MAIN MICROPROCESSOR (QU01)UPDATE PROCEDURE5. MAIN MICROPROCESSOR (QU01)?65.2. Installs of The software (Flash Development Toolkit 3.0)The explanation drawing The explanation drawings are using PM-11S1 in th

33、is section. Please replace with PM-15S1 the portion currently mentioned as PM-11S1, and operate it1. Open the CD-ROM (90M-PM15S1CDR) Disc, and double click soft fold er.2. Double click the FDT setup.exe5.2. ?5.2. ? (Flash Development Toolkit 3.0)? ?PM-11S1?PM-11S1?PM-15S1?1. CD-ROM (90M-PM15S1CDR) ?

34、 soft?2. FDT setup.exe?73. ? Next?3. Click Next.4. Choose the language. And click Next.5. Click Yes.4. ?Next?5. Yes?86. Check to the all check boxes. And click Next.7. Click Next.8. Check to the all check boxes. And click Next.6. ?Next?7. Next?8. ?Next?99. Click Next.9. Next?10. Next?11. Next?10. Cl

35、ick Next.11. Click Next.1012. Install?13. ?14. Finish?12. Click Install.13. The status bar appears.14. Click Finish.115.3. ?1. Start / Programs / Renesas / Flash Development Toolkit 3.0 / Flash Development Toolkit 3.0 ?5.3. The writing software setup procedure.Launch up the writing software.1. Click

36、 Start / Programs / Renesas / Flash De vel -op ment Toolkit 3.0 / Flash Development Toolkit 3.0.2. OK?(?OK?)2. Click OK. (This window appears at every starting.)123. Create a new project workspace?OK?3. Check Create a new project workspace, and click OK.4. Workspace Name?PM-15? (?Project Name?) OK?5

37、. Select Device?H8/3687F? Next?4. PM-15 is inputted into the Workspace name. (It is si mul ta neous ly inputted into Project Name.) Click OK.5. Choose the H8/3687F in Select Device. Click Next. 136. Select Port?Serial Port?Next?7. Enter the CPU crystal frequency for the selected de-vice:?8.0?Next?8.

38、 Select Connection:?BOOT Mode? Select Baud rate:?19200?Next? :Use Default Baud Rate? ? ? ? ? ? ? ? ? ? ?Baud Rate?6. Choose the Serial port No. in the Select Port. Click Next.7. 8.0 is inputted into the Enter the CPU crystal frequency for the selected device:. Click Next.8. Check the BOOT Mode in Se

39、lect Connection. Choose the 19200 in Select Baud rate. Click Next.Remark : Please remove check mark, if it is contained in Use Default Baud Rate.149. Protection?Automatic? Messaging?Advanced? Finish?9. Check the Automatic in Pro tec tion. Check the Advanced in Messaging. Click Finish.?155.4.?1. Star

40、t / Programs / Renesas / Flash Development Toolkit3.0 / Flash Development Toolkit3.0 ?2. OK? ?OK?5.4. Writing procedure1. Click Start / Programs / Renesas / Flash Develop-ment Toolkit3.0 / Flash Development Toolkit3.0.2. Click OK. (This window appears at every starting)3. Open a recent project works

41、pace?OK?4. ?2? PM-15 ?Add Files.?3. Check Open a recent project workspace, and click OK.4. The right click PM-15, and Click Add Files.165. Open the CD-ROM (90M-PM15S1CDR) and double click soft folder.5. ?90M-PM15S1CDR?soft?6. V040708.mot?Add?7. V040708.mot?6. Select V040708.mot, and Click Add.7. The

42、 holder of V040708.mot is made.178. It checks that PM-15S1 and the COM port are connect-ed by RS232C cable.9. Press POWER Button to turn on the unit. The unit is in the boot mode.( LED and LCD display on the front panel disappear.) 10. The right click V040708.mot, and Click Download File.8. PM-15S1?

43、Windows PC?COM?9. POWER?Power On? (?LED?LCD?)10. 4? V040708.mot ?Download File?11. ? ?11. The screen becomes the uploading condition. When writing is Finished, the below message ap pears on the screen. 1812. ?12. The Main microprocessor (QU01) has been Update. 13. Turn off Power switch, then disconn

44、ect FFC cable from PM-15S1.14. Check the version number of the fi rmware Refer to 4. SERVICE MODE on page 3. 13. PM-15S1?FFC?14. VERSION? 3?4. SERVICE MODE? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?1? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

45、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

46、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

47、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

48、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

49、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

50、 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?