Yamaha-MCX1000-das-sm 维修电路原理图.pdf

《Yamaha-MCX1000-das-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-MCX1000-das-sm 维修电路原理图.pdf（111页珍藏版）》请在收音机爱好者资料库上搜索。

1、MCX-1000The MusicCAST system consists of the MCX-1000, theMCX-A10 and the MCX-SP10.This service manual is for the MCX-1000.For the MCX-A10 and the MCX-SP10 service manual,please refer to the following publication number:MCX-A10/MCX-SP10100852When accepting a repair order from the user, be sure toinf

2、orm him/her that the data in HDD cannot be guaranteed.For the repair work, it is recommended to receive MCX-1000 and MCX-A10 as a set.MCX-1000、MCX-A10MCX-SP10構成。MCX-1000用。MCX-A10MCX-SP10下記参照。MCX-A10/MCX-SP10100852修理依頼受際、HDD保証客様伝。修理品MCX-1000MCX-A10預推奨。IMPORTANT NOTICEThis manual has been provided for

3、 the use of authorized YAMAHA Retailers and their service personnel.It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users,and have therefore not been restated.WARNING:Failure to follow appropri

4、ate service and safety procedures when servicing this product may result in personal injury, destruction of expensivecomponents, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service requiredshould be performed by an authorized YA

5、MAHA Retailer or the appointed service representative.IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicabletechnical capabilities, or establish a principle-agent relationship of any form.The data

6、provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA arecontinually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice

7、or obligation toretrofit. Should any discrepancy appear to exist, please contact the distributors Service Division.WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to theground buss in the unit (heavy ga

8、uge black wires connect to this buss).IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.100851P.O.Box 1, Hamamatsu, JapanSERVICE MANUALDIGITAL AUDIO SERVERMCX-1000RadioFans.CN 收音机爱 好者资料库MCX-10002MCX-1000WALLOUTLETEQUIPMENTUNDER T

9、ESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEI TO SERVICE PERSONNEL1. Critical Components InformationComponents having special characteristics are marked sand must be replaced with parts having specifications equalto those originally installed.2. Leakage Current Measurement (For 120V Models Only)W

10、hen service has been completed, it is imperative to verifythat all exposed conductive surfaces are properly insulatedfrom supply circuits.GMeter impedance should be equivalent to 1500 ohm shuntedby 0.15F.GLeakage current must not exceed 0.5mA.GBe sure to test for leakage with the AC plug in both pol

11、arities.WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic(where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency(and possibly other en

12、tities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-SON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeye

13、s to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands beforehandling food.“CAUTION”“F400: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 250V FUSE.”CAUTIONF400: REPLACE WITH SAME TYPE 10A

14、, 250V FUSE.ATTENTIONF400: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 250V.THE COMPACT DISC RECORDER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIEDSERVICE PERSONNEL.I CONTENTSTO SERVICE PERSONNEL . 24PREVENTION OF ELECTRO STATIC DISCHARGE . 5FRONT PANEL . 6REAR PANE

15、LS . 67REMOTE CONTROL PANEL . 7SPECIFICATIONS. 89INTERNAL VIEW . 9DISASSEMBLY PROCEDURES / 分解手順. 1015SERVICE PRECAUTIONS時注意事項 . 16UPDATING FIRMWARE . 1618RECOVERY AFTER REPLACING HDDHDD交換後. 1819RECOVERY AFTER REPLACING MAIN P.C.B.MAIN P.C.B.交換後 . 2021SERVICE MENU. 2122ENTERING SYSTEM IDID書込 . 2324TR

16、OUBLESHOOTING . 2526TEST MODE . 2728DISPLAY DATA . 29IC DATA . 3055BLOCK DIAGRAM. 5657PRINTED CIRCUIT BOARD . 5863PIN CONNECTION DIAGRAM . 64SCHEMATIC DIAGRAM . 6573PARTS LIST. 7589REMOTE CONTROL. 90DIRECTION FOR USE SETUP GUIDE . 9093 QUICK MANUAL . 94112RadioFans.CN 收音机爱 好者资料库MCX-10003MCX-1000? ?

17、?WARNING: Laser SafetyThis product contains a laser beam component. This component may emit invisible, as well as visible radiation, which maycause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used duringservicing of the unit.1) When testing and/o

18、r repairing any component within the product, keep your eyes and skin more than 30 cm away fromthe laser pick-up unit at all times. Do not stare at the laser beam at any time.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.3) CAUTION: Use

19、 of controls, adjustments or performance of procedures other than those specified herein may result inhazardous radiation exposure.Laser Emitting conditions:1. This device is a Class IIIb laser device.Class IIIb meansWith the protective case removed, exposure to the light output from the laser, eith

20、er directly or reflected by a mirror, cancause harm to the eyes, but there is no danger to the eyes from exposure to dispersed reflected laser light. (Generally 0.5W or less)2. Always wear eyeglasses designed for protection against laser light.3. Always wear gloves.4. Have no reflective objects anyw

21、here near this device.5. Figure A shows from where in this device the laser is emitted.6. When switching on the power to the device for the first time, always measure the laser power with a laser power meterand check that the power is no greater than the number of Watts in the specifications.7. Neve

22、r look directly at the laser light while the laser is emitting light.8. Do not allow the laser light to shine directly on your skin while the laser is emitting light.PROTECTION OF EYES FROM LASER BEAM DURING SERVICINGThis set employs a laser. Therefore, be sure to carefullyfollow the instructions be

23、low when servicing.1. Laser Diode Properties Material: GaAlAs Wavelength: 779-789 nm Emission Duration: Pulse Laser Output: DC erase mode max. 20mW (Continuous) Write mode max. 62mW (Max. Cycle 111 ns, Min. Cycle 30 ns at Max. Speed) This output is the value measured at the lens of the Laser PickupU

24、nit.2. When checking the laser diode emission, keep your eyes more than30 cm away from the objective lens.CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardousradiation exposure.Figure AMCX-10004MCX-1000(U, C models)(B, G models)

25、MCX-10005MCX-1000I PREVENTION OF ELECTRO STATIC DISCHARGESome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect tra

26、nsistors andsemiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused byelectro static discharge (ESD).1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body

27、bytouching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should beremoved for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembl

28、y on a conductive surface such as aluminum foil, toprevent electrostatic charge buildup or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static

29、(ESD protected)” can generateelectrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to

30、 install it. (Mostreplacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparableconductive material).7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to thecha

31、ssis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushingtogethe

32、r of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage anES device).Grounding for electro static breakdown prevention1. Human body grounding:Use an anti static wrist strap to discharge the static electricityfrom your body

33、.2. Work table grounding:Put a grounded conductive material (sheet) or iron sheet onthe area where the optical pickup is placed.Caution:The static electricity of your clothes will not be groundedthrough the wrist strap. So take care not to let your clothestouch the optical pickup.1MConductive materi

34、al(sheet) or iron sheetAnti-static wrist strapMCX-10006MCX-1000I FRONT PANELI REAR PANELSMCX-1000 (U, C models)MCX-1000 (A model)MCX-10007MCX-1000I REMOTE CONTROL PANELMCX-1000 (B, G models)MCX-1000 (J model)MCX-10008MCX-1000I SPECIFICATIONS / 参考仕様AUDIO PERFORMANCE / 性能Frequency response . 5 to 20,0

35、00 Hz, 0.5 dBS/N ratio / SN比 (EIAJ)Playback . 105 dBRecording . 92 dBTotal harmonic distortion / 歪率+雑音 (1 kHz)Playback .0.004 %Recording .0.006 %Dynamic range / Playback . 99 dBRecording . 92 dBINPUT/OUTPUT / 入出力仕様LINE OUTPUT / 出力Output level . 2 VrmsOutput resistance . 990 ohmsLINE INPUT / 入力Input

36、sensitivity. 500 mVrmsInput impedance . 23 k-ohms (REC LEVEL Max.)DIGITAL OUTPUT / 出力Coaxial output level .0.5 Vp-p (75 ohms)Optical output level. -20 dBmSampling frequency.44.1 kHzDIGITAL INPUT / 入力Coaxial input level .0.5 Vp-p (75 ohms)Optical input level . -20 dBmInput gain (with Digital Volume)

37、. 12 dBInput gain (without Digital Volume) . 0 dBSampling frequency tolerance. 32 kHz, 44.1 kHz, 48 kHz and 96 kHzHEADPHONE OUTPUT / 出力 (PHONES LEVEL MAX)Output level (-20 dB, 150 ohms load) . 330 mVrmsGENERAL / 一般仕様Application disks / 対応CD, CD-ROM (MP3 only), AUDIO CD-R, AUDIO CD-RWMP3 formats / 対応

38、MP3Disc that is produced in the ISO9660 Level 1 and 2 multi-session Juliet/Romeo format but unusable for packet writemethod.Maximum number of folder layers is 8 and that of the files is300.The file extension is MP3 or mp3.MPEG1 Layer 3 100% compression bit rate is applicable. WithVBR, the time data

39、and bit rate data may not be displayedcorrectly.Based on ID3 Tag ver. 1.1ISO9660 Level 12 Joliet/Romeo作成。非対応。最大階層8。最大数300拡張子MP3mp3MPEG1 Layer3全圧縮対応。VBR時刻情報、情報正表示。ID3ver 1.1準拠HDD storage / HDD容量.80GBLAN Interface / LAN.Ethernet 10/100 Base-TWireless Interface / 無線 . IEEE 802.11bPower supply / 電源電圧U,

40、C models .AC 120 V 60 HzA model.AC 240 V 50 HzB, G models .AC 230 V 50 HzJ model .AC 100 V 50/60 HzPower consumption / 消費電力U, C, A, B, G models . 53 WJ model . 47 WStandby power consumption / 待機電力U, C models . 3.3 WA, B, G models . 2.9 WJ model . 4.1 WOperating temperature / 動作温度 . + 5 C to + 35 CMa

41、x. dimensions / 最大寸法 (W x H x D). 435 x 135.5 x 434.5 mm (17-1/8 x 4-9/16 x 16-5/16).(include legs, knobs and antenna cover)Weight / 質量 .11.5 kg (17 lbs. 3 oz.)Panel color / 色Silver Color . B, G, J modelsBlack Color . U, C, A modelsAccessories / 付属品Remote Control x 1, Battery x 2, Optical Fiber Cabl

42、e x 1, AudioPin Cable x 1, Video Cable x 1* Specifications are subject to change without notice due to productimprovements. 参考仕様外観予告変更。U . U.S.A. modelC . Canadian modelA . Australian modelB . British modelG . European modelJ . Japanese model“Music recognition technology and related data are provide

43、d byGracenote and the Gracenote CDDB Music Recognition Service SM .Gracenote is the industry standard in music recognition technologyand related content delivery. For more information .”“CD and music-related data from Gracenote CDDB MusicRecognition Service SM 2000, 2001, 2002 Gracenote. GracenoteCD

44、DB Client Software 2000, 2001, 2002 Gracenote. U.S. PatentsNumbers #5,987,525; #6,061,680; #6,154,773, and other patentsissued or pending.CDDB is a registered trademark of Gracenote. The Gracenote logoand logotype, the Gracenote CDDB logo and logotype, and the“Powered by Gracenote CDDB” logo are tra

45、demarks of Gracenote.Music Recognition Service and MRS are service marks of Gracenote.”MCX-10009MCX-10001234567890 A435 (17-1/8)3 (1/8)397 (15-5/8)120 (4-3/4)135.5 (5-3/8)15.5 (5/8)434.5 (17-1/8)34.5 (1-3/8)Unit: mm (inch)単位 ： mm （） I INTERNAL VIEW1 FAN2 OPERATION (5) P.C.B.3 OPERATION (6) P.C.B.4 W

46、IRELESS LAN CARD5 HDD UNIT6 MAIN P.C.B.7 OPERATION (2) P.C.B.8 CDR MECHANICAL UNIT9 OPERATION (1) P.C.B.0 OPERATION (4) P.C.B.A OPERATION (3) P.C.B. DIMENSIONSMCX-100010MCX-1000112? ?2. CDR取外a. 5本外、各外。 （Fig. 3）b. CDR持上後方取出。 （Fig. 3）c. CDR電源、IDE外。 （Fig. 2）2. Removal of CDR Mechanical Unita. Remove 5

47、screws (3) and then remove each Stopper.(Fig. 3)b. Remove the CDR Mechanical Unit rearward while liftingit up. (Fig. 3)c. Disconnect the Power Cable and IDE Cable from theCDR Mechanical Unit. (Fig. 2)Fig. 1(Remove parts in the order as numbered.)CDR Mechanical Unit replacementThe CDR mechanical unit

48、 must be replaced as a unit.None of its components can be supplied separately.When replacing the CDR mechanical unit, write downthe following items. Serial No. of the product and the symptom in detail Mechanical serial No./mechanical shipping serialNo. of the CDR mechanical unitWhen sending back the

49、 defective CDR mechanical unitfor repair, send the whole unit.When sending back the defective CDR mechanical unitfor repair, attach the disc that was used when the erroroccurred, if requested. However, Yamaha shall not beliable even if the data in the disc has becomeunreadable while the unit is bein

50、g serviced/repaired.When replacing the CDR mechanical unit, be sure toorder a laser precaution label and a radiation sheet asspare parts and attach them to the new CDRmechanical unit. (Refer to the figure 4 and 5 in P11.)I DISASSEMBLY PROCEDURES / 分解手順1. Removal of Top Covera. Turn off the power, wa