Yamaha-MSR100-spk-sm 维修电路原理图.pdf

《Yamaha-MSR100-spk-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-MSR100-spk-sm 维修电路原理图.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、0.166K-7304 Printed in Japan 02.1120021201-56000SERVICE MANUALPA011662HAMAMATSU, JAPAN CONTENTSSPECIFICATIONS. 3PERFORMANCE GRAPH. 4PANEL LAYOUT. 4CIRCUIT BOARD LAYOUT. 5DIMENSIONS. 5LEVEL DIAGRAM. 6DISASSEMBLY PROCEDURE. 7IC BLOCK DIAGRAM. 12CIRCUIT BOARDS. 12INSPECTIONS. 17BLOCK DIAGRAMCIRCUIT DIA

2、GRAMPARTS LISTMSR100/SMS100POWERED SPEAKERThis document is printed on chlorine free (ECF) paper.MSR100（目次）（総合仕様）（特性図）（）（）（寸法図）（）（分解手順）（IC図）（基板図）（検査）（）（回路図）（ECF：無塩素系漂白）使用。RadioFans.CN 收音机爱 好者资料库MSR100/SMS1002IMPORTANT NOTICEThis manual has been provided for the use of authorized Yamaha Retailers and

3、their service personnel. It has been assumedthat basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-stood by the users, and have therefore not been restated.WARNING :Failure to follow appropriate service and safety procedures when se

4、rvicing this product may result in per-sonal injury, destruction of expensive components and failure of the product to perform as specified. Forthese reasons, we advise all Yamaha product owners that all service required should be performed by anauthorized Yamaha Retailer or the appointed service re

5、presentative.IMPORTANT :This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship ofany form.The data provided is belived to be accurate and ap

6、plicable to the unit(s) indicated on the cover. The research engineering, andservice departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitableand changes in specification are subject to change without notice or obligation to retrofit. Should

7、any discrepancy appear toexist, please contact the distributors Service Division.WARNING :Static discharges can destroy expensive components. Discharge any static electricity your body may haveaccumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect tothis bus

8、.)IMPORTANT :Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply powerto the unit.WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Whereapplicable) comp

9、onents may also contain traces of chemicals found by the California Health and Welfare Agency (and possiblyother entities) to cause cancer and/or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSO EVER!Avoid p

10、rolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or exposeeyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handlingfood.WARNINGComponents having specia

11、l characteristics are marked and must be replaced with parts having specification equal to thoseoriginally installed.WARNING: THIS APPARATUS MUST BE EARTHEDIMPORTANTTHE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVEAs

12、 the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the s

13、afety earth symbol or coloured GREEN and YELLOW.The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.* This applies on

14、ly to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD.印商品、安全維持重要部品。交換場合、安全必指定部品使用下。RadioFans.CN 收音机爱 好者资料库MSR100/SMS1003SPECIFICATIONSGeneral specificationsType2way Bass Reflex Powered SpeakerSpeaker UnitLF: 200 mm ConeHF: 25.4 mm Compression DriverFrequency Range.55 Hz20 kHz (10 dB)Cross Ove

15、r Frequency.4 kHzMaximum Output Level.112 dB (1 m)Dimension (WHD).275 455.5 255 mm Weight.11 kgColor.Black (Approximate Munsell Value 5 PB2/1)Accessories.Power supply cord 2.5 m (AC Inlet type)Option .BWS50-190/260/320,BCS251, BBS251Amp. UnitMax Power.100W at 1 kHz, THD=1%, RL=6 Input Sensitivity.IN

16、PUT 1: 50 dB* (MIC), +4 dB* (LINE)INPUT 2, 3: 10 dB*Input Impedance.INPUT 1, 2, 3: 10 k Output Sensitivity.LINK OUT: 10 dB*Output Impedance.LINK OUT: 10 k ControlsLEVEL Control.INPUT 1, 2, 3, MASTEREQ Control.LOW: 3 dB at 60 HzHIGH: 6 dB at 10 kHzPOWER Switch.ON/OFFConnectorsINPUT 1.XLR-3-31 (balanc

17、ed)INPUT 2, 3.Phone (unbalanced)LINK OUT.Phone (unbalanced)IndicatorPOWER Indicator.Green LEDCLIP Indicator.Red LEDPower RequirementUSA and Canada.AC 120 V, 60 HzEurope.AC 230 V, 50 HzAustralia.AC 240 V, 50 Hz Korea.AC 220 V, 60 HzPower Consumption.70 W* 0 dB=0.775 VFor European ModelPurchaser/User

18、Information specified in EN55103-1 andEN55103-2.Inrush Current: 10A Conformed Environment: E1, E2, E3 and E4総合仕様 総合仕様形式型LF: 200mmHF: 25.4mm再生周波数帯域.55Hz 20kHz(-10dB)周波数.4kHz最大出力音圧 .112dB （軸上 1m）最大外形寸法（ W H D） .275 455.5 255mm質量.11kg色 .黒（近似値5PB2/1）付属品.電源（AC 型、2.5m）.BWS50-190/260/320、BCS251、BBS251 部定格最

19、大出力 .100W at 1kHz、THD=1%、RL=6入力感度 .INPUT 1:-50dB*（MIC）、+4dB*（LINE）INPUT 2、3: -10dB*入力.INPUT1、2、3: 10k出力感度.LINK OUT: -10dB*出力.LINK OUT: 10kLEVEL.INPUT1、2、3、MASTEREQ.LOW: 3dB at 60HzHIGH: 6dB at 10kHzPOWER.ON/OFFINPUT1.XLR-3-31（型）INPUT2、3. （型）LINK OUT. （型）POWER.緑色発光LEDCLIP.赤色発光LED電源.AC100V、50/60Hz消費電力

20、.65W*0dB=0.775VMSR100/SMS1004POWER SwitchINPUT1 ConnectorSensitivity SwitchINPUT2 and INPUT3 ConnectorsLEVEL ControlsEQ ControlsLINK OUT ConnectorMASTER LEVEL ControlCLIP IndicatorPOWER IndicatorAC IN Connector Rear PanelPERFORMANCE GRAPHPANEL LAYOUT10k1k10020FREQUENCY (Hz)RESPONSE (dB)-40-30-20-100

21、+101234567891011（） （電源 ） （入力1 端子） （感度切換） （入力2 端子、入力3 端子） （音量 ）（音質 ） （出力 端子） （全体音量 ） （ ） （電源 ） （電源入力 端子）（）（特性図）MSR100/SMS1005DIMENSIONSUnits: mmCIRCUIT BOARD LAYOUT455.51372752551202-M8x25*LOWHIGH100(-10dB)EPSSER.NO.MADE IN CHINA100V 65W 50/60HzMODEL MSR100POWERED SPEAKERMASTERMASTERLINK OUTEQINPUT O

22、N/OFFAC INPOWERPOWERCLIP(-10dB)LINE(-10dB)LINELINE(+4dB)MIC(-50dB)3LEVEL+3-3+6-6100LEVEL100LEVEL21010LEVEL132NEUTRIKPower transformer（電源）Power transformer Right side view Rear view （電源）Power amplifier assembly（Assy） Power amplifier assembly（Assy） NETWORKNETWORKPOWER AMPLIFIERPOWER AMPLIFIERPOWER SWI

23、TCHEQACACINPOWER SWITCHEQIN（寸法図）( 単位)（）MSR100/SMS1006LEVEL DIAGRAMOUTPUT(10dBu)INPUT1INPUT2, 3(LINE)0dBu+4dBu-10dBu-50dBu-4.7dBu-2.2dBu+29.9dBu (SP OUT)INPUT1(MIC)INPUT3(10dBu)INPUT2(10dBu)INPUT1(50dBu/+4dBu)MICLINELFHF6 100WNWMASTERLEVELEQHIGHLOWLOWCUTLOWBOOSTP.AMP（）MSR100/SMS1007DISASSEMBLY PROCED

24、URE1.Front Grille Assembly(Time required: About 1 minute)1-1Remove the four (4) screws marked 100A. The frontgrille assembly can then be removed. (Fig.1)2.Speaker LF (Woofer)(Time required: About 2 minutes)2-1Remove the front grille assembly. (See procedure 1.)2-2Remove the four (4) screws marked 80

25、. Thespeaker LF (Woofer) can then be removed. (Fig.1)2-3Remove the wire LF (red/black) installed to thespeaker LF (Woofer). (Photo.1)3.Front Cabinet Unit and Rear Cabinet Unit(Time required: About 3 minutes)3-1Remove the front grille assembly. (See procedure 1.)3-2Remove the speaker LF (Woofer). (Se

26、e procedure 2.)3-3Remove the five (5) screws marked 50A and the four(4) screws marked 50B. The front cabinet unit andthe rear cabinet unit can then be divided. (Fig.1, 2)Take care not to damage the speaker HF(Tweeter) terminal when opening the frontcabinet unit and the rear cabinet unit.1. Assy (所要時

27、間：約1 分)1-1100A4 本外、 Assy外。 (図1)2. LF() (所要時間：約2 分)2-1Assy 外。 (1 項参照)2-2804本外、 LF()外。 (図1)2-3 LF()取付束線LF(赤黒)外。 (写真1)3.部、部 (所要時間：約3 分)3-1Assy 外。 (1 項参照)3-2LF()外。 (2項参照)3-350A5本50B4本外、部部別。 (図1, 2) 部部開、 HF （） 端子傷注意下。Fig.150A:Bind Head Tapping Screw-A5.0X35 BL (AAX42210)80:Bind Head Tapping Screw-B4.0X18

28、 BL (AAX42230)100A: Bind Head Tapping Screw-B4.0X10 BL (AAX12100)(図2)50B:Bind Head Tapping Screw-A5.0X35 BL (AAX42210)*LOWHIGH100(-10dB)EPSSER.NO.MADE IN CHINA100V 65W 50/60HzMODEL MSR100POWERED SPEAKERMASTERMASTERLINK OUTEQINPUT ON/OFFAC INPOWERPOWERCLIP(-10dB)LINE(-10dB)LINELINE(+4dB)MIC(-50dB)3LE

29、VEL+3-3+6-6100LEVEL100LEVEL21010LEVEL132NEUTRIK100A100A50A50A50B50B50B50B50A80100A50A8080100A50A80Front cabinet unitSpeaker LF (Woofer)(部)(LF ()Front grille assembly(Assy) Front view Rear view Rear cabinet unit(部)(束線LF (黒)(LF ()(束線LF (赤)Speaker LF (Woofer)Wire LF (Black)Wire LF (Red)Photo.1 (写真1)（分解

30、手順）(A)(B)(B)(図1)Fig.2(A)MSR100/SMS10084.Speaker HF (Tweeter)(Time required: About 3 minutes)4-1Remove the front grille assembly. (See procedure 1.)4-2Divide the front cabinet unit and the rear cabinetunit. (See procedure 3.)4-3Remove the wire HF (yellow/blue) installed to thespeaker HF (Tweeter). (P

31、hoto.2)4-4Remove the two (2) screws marked 46. The speakerHF (Tweeter) can then be removed from the frontcabinet unit. (Fig.3)5.Network Assembly and NETWORK CircuitBoard (Time required: About 4 minutes)5-1Remove the front grille assembly. (See procedure 1.)5-2Divide the front cabinet unit and the re

32、ar cabinetunit. (See procedure 3.)5-3Remove the four (4) screws marked 10e. Thenetwork assembly can then be removed from therear cabinet unit. (Fig.4)5-4Remove the four (4) screws marked N40. Thenetwork holders C and D can then be removed fromthe NETWORK circuit board. (Fig.4)Remove the P1, P2 conne

33、ctor assembly solderedto the NETWORK circuit board.4.HF() (所要時間：約3分)4-1Assy 外。 (1項参照)4-2部部別。 (3項参照)4-3HF()取付束線HF(黄青)外。 (写真2)4-4462本外、 部HF()外。 (図3)5.Assy、 (所要時間：約4 分)5-1Assy 外。 (1項参照)5-2部部別。 (3項参照)5-310e4本外、 部Assy 外。 (図 4)5-4N404本外、固定金具 C、D外。 (図4)取付線材P1、P2半田外、外。46: Bind Head Tapping Screw-B 4.0X20 BL

34、 (AAX42200)Fig.3Fig.410e:Bind Head Tapping Screw-B 3.0X10 BL (AAX10840)N40:Cup Screw-B PW3.0X8 Y (AAX43390)46Front Cabinet Unit(部)Speaker HF (Tweeter)(HF ()Network assembly（Assy)Network holder D（固定金具D)Network holder C（固定金具C)N4010eRear Cabinet Unit(部)NETWORK(束線HF (黄)(HF ()(束線HF (青)Speaker HF (Tweeter

35、)Wire HF (Yellow)Wire HF (Blue)Photo.2(B)(図3)(B)(B)(図4)(写真2)MSR100/SMS10096.Amplifier Assembly(Time required: About 1 minute)6-1Remove the ten (10) screws marked 30. Theamplifier assembly can then be removed. (Fig.5)7.EQ Circuit Board, IN PCB Assembly andIN Circuit Board(Time required: About 3 minut

36、es each)7-1Remove the amplifier assembly. (See procedure 6.)7-2Remove the eight (8) screws marked 210. Theshield case assembly can then be removed. (Fig.5,Photo.3)7-3EQ Circuit Board:7-3-1Remove the six (6) knobs marked 110 and the six(6) hexagonal nuts marked A. The EQ circuit boardcan then be remo

37、ved. (Fig.5, Photo.3)7-4IN PCB Assembly and IN Circuit Board:7-4-1Remove the three (3) hexagonal nuts marked 130and the three (3) screws marked 160. The IN PCBassembly can then be removed. (Fig.5, Photo.3)7-4-2Remove the screw marked 150c. The angle L canthen be removed from the IN circuit board. (F

38、ig.6)6.Assy (所要時間：約1分)6-13010本外、 Assy外。(図5)7.EQ 、IN Assy、IN (所要時間：各約3分)7-1Assy 外。 (6 項参照)7-22108本外、Assy外。 (図5, 写真3)7-3EQ:7-3-1110 6 個A六角 6 個外、EQ 外。 (図5, 写真3)7-4IN Assy、IN:7-4-1130特殊六角 3個160 3本外、IN Assy 外。 (図5, 写真3)7-4-2150c1本外、INL金具外。 (図6)20:Bonding Tapping Screw-B 4.0X8 BL BO (AAX43620)30:Bind Head

39、 Tapping Screw-B4.0X14 BL (AAX42170)100B: Bonding Tapping Screw-B 3.0X10 BL BO (AAX12110)130:Hexagonal Nut M12.0 BL160:Bonding Tapping Screw-B3.0X10 BL BO (AAX12110)180:Pan Head Tapping Screw-B 3.0X12 BL (AAX43370)210:Bonding Tapping Screw-B 3.0X10 BL BO (AAX12110)A:Hexagonal NutWasherFig.5*LOWHIGH1

40、00(-10dB)EPSSER.NO.MADE IN CHINA100V 65W 50/60HzMODEL MSR100POWERED SPEAKERMASTERMASTERLINK OUTEQINPUT ON/OFFAC INPOWERPOWERCLIP(-10dB)LINE(-10dB)LINELINE(+4dB)MIC(-50dB)3LEVEL+3-3+6-6100LEVEL100LEVEL21010LEVEL132NEUTRIK303030303030130 x 3110 x 6210 x 830A x 6160 x 2160100B x 2303030180 x 82020Power

41、 transformer(電源)Power amplifier assembly(Assy)Shield case assembly(Assy)Amplifier assembly(Assy)Push knob() Rear view ACINEQPOWER SWITCHPOWER AMPLIFIER(図5)(B) (B)(B)(B) (B) (B)(六角)(特殊六角)()MSR100/SMS100108.Power Amplifier Assembly and POWERAMPLIFIER Circuit Board(Time required: About 4 minutes)8-1Rem

42、ove the amplifier assembly. (See procedure 6.)8-2Remove the shield case assembly. (See procedure7-2.)8-3Remove the eight (8) screws marked 180. Thepower amplifier assembly can then be removed.(Fig.5, Photo.3)8-4Remove the screw marked P40, the five (5) screwsmarked P80 and the four (4) screws marked

43、 P90.The POWER AMPLIFIER circuit board can then beremoved. (Fig.7)Power switch assembly(電源Assy)Power transformer assembly(電源Assy)Power transformer(電源)Power amplifier assembly(Assy)Shield case assembly(Assy)IN PCB assembly(INAssy)ACINPOWER SWITCHPOWER AMPLIFIERAmplifier Assembly (Assy) Front view EQP

44、hoto.3Fig.6150c:Cup Screw-BPW3.0X8 Y (AAX43390)Fig.7P40: Bind Head Tapping Screw-B 3.0X10 BL (AAX10840)P80: Cup Screw-BPW3.0X8 Y (AAX43390)P90: Cums Head ScrewSP3.0X14 BL (AAX43410)Angle L（L金具）150cIN PCB Assembly(INAssy)INP40P80P90Power Amplifier Assembly(Assy)POWER AMPLIFIERP80P808.Assy、 (所要時間：約4 分

45、)8-1Assy 外。 (6項参照)8-2 Assy外。 (7-2項参照)8-31808本外、Assy外。 (図5, 写真3)8-4P40 1 本P80 5 本、 P90 4本外、 外。 (図7)(図6)(B)(図7)(B)(B) (小)(写真3)MSR100/SMS10011Fig.890d: Flat Head Screw 3.0X6 BL (AAX42430)Power Switch Assembly(電源Assy)90dPower switch holder(電源取付金具)Push knob()POWER SWITCHAC(半田付)SolderingPower Transformer

46、Assembly(電源Assy)Power transformer(電源)Photo.4 (写真4)9.Power Transformer Assembly (PowerTransformer and AC Circuit Board)(Time required: About 3 minutes)9-1Remove the amplifier assembly. (See procedure 6.)9-2Remove the four (4) screws marked 20. The powertransformer assembly can then be removed. (Fig.5

47、,Photo.3)9-3Remove the power transformer soldered to the ACcircuit board. (Photo.4)10.Power Switch Assembly and POWERSWITCH Circuit Board(Time required: About 3 minutes)10-1Remove the amplifier assembly. (See procedure 6.)10-2Remove the two (2) screws marked 100B. Thepower switch assembly can then b

48、e removed. (Fig.5,Photo.3)10-3Remove the two (2) screws marked 90d. The powerswitch holder and the push knob can then beremoved from the POWER SWITCH circuit board.(Fig.8)(皿小M3X6)9.電源 Assy(電源、AC)(所要時間：約3分)9-1Assy 外。 (6項参照)9-2204本外、電源Assy 外。 (図5, 写真3)9-3AC半田付電源外。 (写真4)10.電源Assy、 電源(所要時間：約3 分)10-1Assy

49、 外。 (6項参照)10-2100B2本外、電源Assy外。 (図5, 写真3)10-390d 2 本外、電源電源取付金具外。 (図8)(図8)MSR100/SMS10012IC BLOCK DIAGRAMAC Circuit Board (6448D-20) .12EQ Circuit Board (6448B-20) .14IN Circuit Board (6448A-20).15NETWORK Circuit Board (6448F-20) .16POWER AMPLIFIER Circuit Board (6448C-20).13POWER SWITCH Circuit Board

50、 (6448E-20).12CIRCUIT BOARDSNote: See parts list for details of circuit board component parts. AC Circuit BoardComponent sideAC, POWER SWITCH: 374005（基板図）注： 部品詳細参照下。PC4570HA (AAX42560)Dual Operational AmplifierEQ: IC201-203IN: IC101,1031A23456789+V-IN-V+INOUTAAA+V-IN+INOUTBBB-+B-+（部品側）to POWER AMPLI