JVC-RX5060B-avr-sm 维修电路原理图.pdf

《JVC-RX5060B-avr-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-RX5060B-avr-sm 维修电路原理图.pdf（14页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2006 Victor Company of Japan, LimitedNo.MB5042006/2AUDIO/VIDEO CONTROL RECEIVERMB50420062RX-5060BJ,RX-5060BC,RX-5060BE,RX-5062SB,RX-5062SE,RX-5062SEN,RX-5062SEVLead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)TABLE OF CONTENTS1PRECAUTION

2、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-42SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-63DISASSEMB

3、LY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-74ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、. 1-135TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13TA/NEWS/INFODISPLAY MODERadioFans.CN 收音机爱 好者资料库1-2 (No.MB504)SPECIFICATIONNorthern america versionAmplifierOutput Power Front channels100 W per

5、 channel, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmonic distortion.Center channel100 W, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmon-ic distortion.Surround channels100 W per channel, min. RMS, driven int 8 , at 1 kHz with no more than 10% total harm

6、onic distortion.AudioAudio Input Sensitivity/Impedance (1 kHz)CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 220 mV/47 kAudio Input (DIGITAL IN)*CoaxialDIGITAL 1 (DVD) : 0.5 V(p-p)/75 OpticalDIGITAL 2 (CD) : -21 dBm to -15 dBm (660 nm 30 nm)Recording Output LevelTAPE/CDR, VCR : 220 mVSignal-to-Noise Ratio

7、(66 IHF/78 IHF)CD, TAPE/CDR, VCR, TV SOUND, DVD : 62 dB/71 dBFrequency Response (8 )CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 20 Hz to 20 kHz (1 dB)Equalization (5 bands)63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz : 8 dB (in 2 dB steps)VideoVideo Input Sensitivity/Impedance Composite video DVD, VCR, AUX : 1 V

8、(p-p)/75 Video Output LevelComposite video VCR, MONITOR OUT : 1 V(p-p)/75 SynchronizationNegativeSignal-to-Noise Ratio45 dBFM tuner (IHF)Tuning Range87.5 MHz to 108.0 MHzUsable SensitivityMonaural12.8 dBf (1.2 V/75 )50 dB Quieting SensitivityMonaural16.0 dBf (1.7 V/75 )Stereo37.5 dBf (20.5 V/75 )Ste

9、reo Separation at OUT (REC)35 dB at 1 kHzAM tunerTuning Range530 kHz to 1 710 kHzGeneralPower RequirementsAC 120V , 60 HzPower Consumption155 W/200 VA (at operation)0.8 W (in standby mode)Dimensions (W H D)435 mm 146.5 mm 369.5 mmMass7.0 kgRadioFans.CN 收音机爱 好者资料库(No.MB504)1-3Europian version* Corres

10、ponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency?32 kHz, 44.1 kHz, 48 kHz)Designs and specifications are subject to change without notice.AmplifierOutput Power Front channels100 W per channel, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmo

11、nic distortion.Center channel100 W, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmon-ic distortion.Surround channels100 W per channel, min. RMS, driven into 8 , at 1 kHz with no more than 10% total harmonic distortion.AudioAudio Input Sensitivity/Impedance (1 kHz)CD, TAPE/CDR, V

12、CR, TV SOUND, DVD, AUX : 220 mV/47 kAudio Input (DIGITAL IN)CoaxialDIGITAL 1 (DVD) : 0.5 V(p-p)/75 OpticalDIGITAL 2 (CD) : -21 dBm to -15 dBm (660 nm 30 nm)Recording Output LevelTAPE/CDR, VCR : 220 mVSignal-to-Noise Ratio (66 IHF/DIN)CD, TAPE/CDR, VCR, TV SOUND, DVD : 66 dB/62 dBFrequency Response (

13、8 )CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 20 Hz to 20 kHz (1 dB)Equalization (5 bands)63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz : 8 dB (in 2 dB steps)VideoVideo Input Sensitivity/Impedance Composite video DVD, VCR, AUX : 1 V(p-p)/75 Video Output LevelComposite video VCR, MONITOR OUT : 1 V(p-p)/75 Synchro

14、nizationNegativeSignal-to-Noise Ratio45 dBFM tuner (IHF)Tuning Range87.50 MHz to 108.00 MHzUsable SensitivityMonaural17.0 dBf (1.9 V/75 )50 dB Quieting SensitivityMonaural21.3 dBf (3.2 V/75 )Stereo41.3 dBf (31.8 V/75 )Stereo Separation at OUT (REC)35 dB at 1 kHzAM (MW) tunerTuning Range522 kHz to 1

15、629 kHzGeneralPower RequirementsAC 230 V , 50 HzPower Consumption140 W (at operation)0.8 W (in standby mode)Dimensions (W H D)435 mm 146.5 mm 369.5 mmMass7.0 kg1-4 (No.MB504)SECTION 1PRECAUTION1.1Safety Precautions(1) This design of this product contains special hardware andmany circuits and compone

16、nts specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufacturer. Replacement parts must be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alte

17、rations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or additions will voidthe manufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage result

18、ing therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not evident from visual inspection nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher volt

19、age, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical components having such featuresare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutere

20、placement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create shock, fire, orother hazards.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated f

21、romlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the original lead routingand dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakag

22、e shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, knobs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.

23、Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using aLeakage Current Tester, measure the leakage currentfrom each exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known goo

24、d earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC voltmeter having, 1,000 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor b

25、etween an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection to each exposed metalpart, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor.

26、Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). 1.2Warning(1) This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility o

27、f the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is essential that safety critical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3C

28、autionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair of this system.1.4Critical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams

29、, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the mark nearby are criticalfor safety. When replacing them, be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C

30、version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE(No.MB504)1-51.5Importance administering point on the safetyGraphic symbol mark (This symbol means fast blow type fuse.)FOR CONTINUED PROTECTION AGAINST R

31、ISKOF FIRE, REPLACE ONLY WITH SAME TYPEAND RATING OF FUSES ;should be read as follows ;F201,F206,F207: 5A 125V F202,F203 : 2A 125VF201,F206,F207: 5A 125V F202,F203 : 2A 125VFull Fuse Replacement MarkingFUSE CAUTIONLe symbole graphique (Ce symbole signifiefusible de type a fusion rapide.)POUR UNE PRO

32、TECTION CONTINUE CONTREDES RISQUES DINCENDIE, REMPLACERSEULEMENT PAR UN FUSIBLE DU MEME TYPE ;Marquage Pour Le RemplacementComplet De FusiblePRECAUTIONS SUR LES FUSIBLESdoit etre interprete comme suit ;CN251FC272FC221FC222FC231FC232FW201R201FC261110111112113114120121122130131FC262FC271FC211FC212R1EP

33、1B106B105B104TA201TA202PW104PW102PW105PW103PW101B103B102B101B108B107B109B1101-6 (No.MB504)SECTION 2SPECIFIC SERVICE INSTRUCTIONSThis service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.(No.MB504)1-7SECTION 3DISASSEMBLY3.1Main body3.1.1Removing the top cover (See Fig. 1 and 2)(1) Remove th

34、e three screws A attaching the top cover.(2) Remove the four screws B attaching the both side of topcover.Fig.1Fig.2AB1-8 (No.MB504)3.1.2Removing the front panel assembly (See Fig. 3 to 5)(1) Remove the three screws C attaching the top side of frontpanel assembly.(2) Remove the four screws D attachi

35、ng the bottom side offront panel assembly.(3) Remove the one screw E attaching the ground wire to frontchassis.(4) Disconnect the connector to CN404 of audio board, CN504of video board, CN402 of main board and CN201 of regu-lator board.Fig.3Fig.4Fig.5CDECN504CN404CN402CN201Regulator boardMain board(

36、No.MB504)1-93.1.3Removing the rear panel and each I/O boards (See Fig. 6 to 8)(1) Remove the two screws F attaching the tuner board.(2) Disconnect the card wire from CN411 of main board.(3) Remove the three screws G attaching the digital board.(4) Disconnect the connector CN481 and CN482 of mainboar

37、d.(5) Remove the four screws H attaching the main board andremove the one screw J attaching the ground wire to frontboard.(6) Disconnect the connector CN421 of main board.(7) Remove the two screws K attaching the subwoofer board.(8) Disconnect the connector CN431 of main board.(9) Remove the three s

38、crews L attaching the video board (forEuropean model, two screws L see Fig. 8)(10) Remove the two screws M attaching the speaker terminalboard.(11) Remove the one screw N attaching the fuse board.(12) Remove the three screws P attaching the rear panel.Fig.6Fig.7Fig.8GFKJHLMCN481CN482CN421CN431CN441C

39、N411Digital boardAudio boardSubwoofer boardTunerVideo boardK1-10 (No.MB504)3.1.4Removing the main board (See Fig. 9)(1) Disconnect the connector CN471, CN472 and CN473 fromfront board.(2) Disconnect the connection board from CN291 of regulatorboard and CN491 of main board.(3) Remove the two screws Q

40、 and one screw R attaching themain board.Fig.93.1.5Removing the front board and heat sink (See Fig. 10)(1) Disconnect the connector from CN203 and CN241 of reg-ulator board.(2) Disconnect the connector from CN251 of transformerboard.(3) Remove the four screws S attaching the heat sink.(4) Remove the

41、 one screw T attaching the front board.Fig.10CN491CN291RQCN471CN472Main boardRegulator boardConnectionboardCN473CN241CN203CN251Trans boardRegulatorboardFront boardHeat sinkTSS(No.MB504)1-113.1.6Removing the power transformer and regulator board (See Fig. 11 and 12)(1) Remove the four screws U attach

42、ing the power transform-er.(2) Remove the one screw V attaching the fuse board.(3) Remove the three screws W and one screw X attaching theregulator board.(4) Disconnect the wire from CN101 of headphone board.Fig.11Fig.123.1.7Removing the headphone board (See Fig. 13)(1) Remove the nut Y attaching th

43、e head phone board.Fig.13VUUFuse boardPower transCN101WWXRegulator boardHeadphone jackY1-12 (No.MB504)3.2Front panel assembly3.2.1Removing the micon board (See Fig. 14 and 16)(1) Take out the volume knob from front panel assembly.(2) Remove the nut Z attaching the volume.(3) Remove the nine screws A

44、A attaching the micon board.3.2.2Removing the power switch board (See Fig. 15)(1) Remove the two screws BB attaching the power switchboard.3.2.3Removing the AUX board (See Fig. 14 and 16)(1) Take out the multi jog knob from front panel assembly.(2) Remove the three screws CC attaching the AUX board.

45、Fig.14Fig.15Fig.16Volume knobMulti jog knobZAABBPower switchboardMicon boardAux board(No.MB504)1-13SECTION 4ADJUSTMENTThis service manual does not describe ADJUSTMENT.SECTION 5TROUBLESHOOTINGThis service manual does not describe TROUBLESHOOTING.(No.MB504)Audio/Video Systems Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,JapanVictor Company of Japan, LimitedVPTPrinted in Japan