JVC-THM45-ddcs-sm 维修电路原理图.pdf

《JVC-THM45-ddcs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-THM45-ddcs-sm 维修电路原理图.pdf（85页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LIMITEDNo.MB0332003/11DVD DIGITAL CINEMA SYSTEMMB033200310TH-M45TABLE OF CONTENTS1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32SPEC

2、IFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-84ADJUS

3、TMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-345TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4、-39 Area suffixB - U.K.E - Continental EuropeEN - Northern EuropeXV-THM45SP-PWM45SP-THM45CSP-THM45FSP-THM45F SP-THM45SSP-THM45SRadioFans.CN 收音机爱 好者资料库1-2 (No.MB033)SPECIFICATIONDesign and specifications are subject to change without notice.Center unitAudio sectionTotal Harmonic Distortion0.02%NOTE :

5、 This value is measured at System cord CONNECTOR for reference.Audio input sensitivity/Impedance (at 1 kHz)Analog inputAUX IN290 mV/47 kDigital input*DIGITAL IN (OPTICAL)-21 dBm to -15 dBm (660 nm 30 nm)* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency -

6、 32 kHz, 44.1 kHz, 48 kHz)Video sectionColor SystemPALHorizontal Resolution500 linesSignal-to-Noise Ratio (Composite signal when RGB is selected)64 dBVideo output levelComposite1.0 V(p-p)/75 S-video-Y1.0 V(p-p)/75 S-video-C0.286 V(p-p)/75 Tuner sectionTuning RangeFM87.5 MHz to 108.0 MHzAM (MW)522 kH

7、z to 1629 kHzGeneralPower RequirementsAC 230 V, 50 HzPower Consumption20 W (at operation), 1.6 W (in standby mode)Dimensions (W H D)400 mm 85 mm 386 mmMass4.6 kgSubwooferAmplifier sectionFront/Center/Surround80 W per channel, RMS at 6 at 1 kHz, with 10 % total harmonic distortion.Subwoofer120 W, RMS

8、 at 4 at 100 Hz, with 10 % total harmonic distortion.Speaker sectionSpeaker unit16 cm Bass-reflex, Magnetically ShieldedFrequency Range30 Hz to 200 HzGeneralPower RequirementsAC 230 V, 50 HzPower Consumption150 W (at operation), 0 W (in standby mode)Dimensions (W H D)216 mm 353 mm 485 mmMass12.0 kgS

9、atellite SpeakersFront speakers (SP-THM45F)Speakers8.0 cm Bass-reflex, Magnetically ShieldedPower Handling Capacity80 WImpedance6 Frequency Range90 Hz to 20 kHzDimensions (W H D)103 mm 115 mm 100 mmMass0.64 kgSurround speakers (SP-THM45S)Speakers8.0 cm Bass-reflex, Magnetically ShieldedPower Handlin

10、g Capacity80 WImpedance6 Frequency Range90 Hz to 20 kHzDimensions (W H D)103 mm 115 mm 100 mmMass0.52 kgCenter speakerSpeakers8.0 cm Bass-reflex, Magnetically ShieldedPower Handling Capacity80 WImpedance6 Frequency Range90 Hz to 20 kHzDimensions (W H D)103 mm 115 mm 100 mmMass0.64 kgAccessoriesRemot

11、e control (1), Batteries (2), FM antenna (1), AM (MW) loop antenna (1), Power cord (1), System cord (1)Speaker codes5 mFor satellite (front left/right) and center speakers (3)10 mFor satellite speakers (surround left/right) (2) (The length of the above speaker cords are approximate.)RadioFans.CN 收音机

12、爱 好者资料库(No.MB033)1-3SECTION 1PRECAUTION1.1Safety Precautions(1) This design of this product contains special hardware andmany circuits and components specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufactu

13、rer. Replacement parts must be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alterations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or ad

14、ditions will voidthe manufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resulting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not ev

15、ident from visual inspection nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher voltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical compo

16、nents having such featuresare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create sh

17、ock, fire, orother hazards.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the o

18、riginal lead routingand dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, kn

19、obs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using aLeakage Current Tester, measure the le

20、akage currentfrom each exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known good earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC

21、voltmeter having, 1,000 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection

22、to each exposed metalpart, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r

23、.m.s.). 1.2Warning(1) This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is esse

24、ntial that safety critical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair o

25、f this system.1.4Critical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the mark nearby are criticalfor safety. When r

26、eplacing them, be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity) 0.15 F AC TYPE1-4 (No.MB033)1

27、.5 Safety Precautions (U.K only)(1) This design of this product contains special hardware and many circuits and components specially for safety purposes. For con-tinued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replace-ment parts m

28、ust be identical to those used in the original circuits.(2) Any unauthorised design alterations or additions will void the manufacturers guarantee; furthermore the manufacturer cannotaccept responsibility for personal injury or property damage resulting therefrom.(3) Essential safety critical compon

29、ents are identified by ( ) on the Parts List and by shading on the schematics, and must neverbe replaced by parts other than those listed in the manual. Please note however that many electrical and mechanical parts inthe product have special safety related characteristics. These characteristics are

30、often not evident from visual inspection. Partsother than specified by the manufacturer may not have the same safety characteristics as the recommended replacement partsshown in the Parts List of the Service Manual and may create shock, fire, or other hazards.(4) The leads in the products are routed

31、 and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts,high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service isrequired, the original lead routing and dress should be observed, and it should

32、be confirmed that they have been returned tonormal, after re-assembling.1.5.1Warning(1) Service should be performed by qualified personnel only.(2) This equipment has been designed and manufactured to meet international safety standards.(3) It is the legal responsibility of the repairer to ensure th

33、at these safety standards are maintained.(4) Repairs must be made in accordance with the relevant safety standards.(5) It is essential that safety critical components are replaced by approved parts.(6) If mains voltage selector is provided, check setting for local voltage.Burrs formed during molding

34、 may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.(No.MB033)1-51.6Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can

35、destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.6.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players. Be careful to use pr

36、oper grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to r

37、elease any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement opticalpickup are shorted. After replacement, return the shorted parts to their original condit

38、ion. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easilydestroy the laser diode. 1.7Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as

39、 it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to thereplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too lo

40、nga time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.8Attention when traverse unit is decomposed*Please refer to Di

41、sassembly method in the text for the DVD pickup unit. Apply solder to the short circuit points before the flexible wire is disconnected from the connector on the DVD pickup.(If the flexible wire is disconnected without applying solder, the DVD pickup may be destroyed by static electricity.) In the a

42、ssembly, be sure to remove solder from the short land sections after connecting the flexible wire.1MConductive material(conductive sheet) or iron palate(caption)Anti-static wrist strapDVD pickupDVD changer mechanism assemblyShort circuit points1-6 (No.MB033)1.9Important for laser products1.CLASS 1 L

43、ASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact d

44、isc player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are de feated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is ab

45、le to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.(No.MB033)1-7SECTION 2SPECI

46、FIC SERVICE INSTRUCTIONSThis service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.1-8 (No.MB033)SECTION 3DISASSEMBLY3.1Main body section3.1.1Removing the metal cover (See Figs.1 to 4)(1) From the right and left sides of the main body, remove thefour screws A attaching the metal cover. (See

47、 Figs.1 and2.)(2) From the back side of the main body, remove the threescrews B attaching the metal cover. (See Fig.3.)(3) Lift the rear section of the metal cover in the direction of thearrow while extending the lower sections of the metal cov-er, release the claws a using a longer screwdriver from

48、 theinside as required. (See Fig.4.)Note:Do not damage any parts and boards inside the main bodywhen releasing the joints a using a longer screwdriver.Fig.1Fig.2Fig.3Fig.4Metal coverAMetal coverAMetal coverRear panelBMetal coverClaws aClaws a(No.MB033)1-93.1.2Removing the front panel assembly (See F

49、igs.5 and 6) Remove the metal cover.(1) From the top side of the main body, disconnect the parallelwires from the connectors (CN408, CN409) on the mainboard. (See Fig.5.)(2) Disconnect the card wires from the connectors (CN407,CN412) on the main board. (See Fig.5.)(3) Remove the screw C attaching th

50、e earth wire to the mainboard. (See Fig.5.)(4) From the bottom side of the main body, remove the threescrews D attaching the front panel assembly. (See Fig.6.)(5) Release the two hooks b and hook c from the both and bot-tom sides of the main body, and remove the front panel as-sembly in the directio