Sony-TAF3A-int-sm 维修电路原理图.pdf

《Sony-TAF3A-int-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-TAF3A-int-sm 维修电路原理图.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、RadioFans.CN 收音机爱 好者资料库GENERAL Weight:Power Requirements: 120V ac, 60 Hz (US, Canadian Model)220 V ac, 50160 Hz (AEP Model)240 V ac, 50/60 Hz (UK Model)120 or 220V ac adjustable. 50/60 Hz (E Model)Power Consumption:Dimensions:SPECIFICATIONS85 W (US Model)140W Canadian Model)AMPLIFIER SECTION210W (AE

2、P, E Model)240W (UK Model)Continuous RMSApprox. 435 (w) x 145 (h) x 370 (d) mmPower output:17 1/8(w) x 53/4(h) x 14%ldl inches(Less than 0.5% THD)(US, Canadian Model)Approx. 410 (w) x 145 (h) x 370 (d) mm161/4(w) x 5%(h) x(AEP, UK, E Model)141/,ldlinchesIncluding projecting parts and controlsPower B

3、andwidth (IHF):SAFETY-RELATED COMPONENT WARNING!Damping Factor:COMPONENTS IDENTIFIED BY SHADING AND AMARK ON THE SCHEMATIC DIAGRAMS, EXPLODEDVIEWS AND IN THE PARTS LIST ARE CRITICAL TOSAFE OPERATION. REPLACE THESE COMPONENTSWITH SONY PARTS WHOSE PART NUMBERS APPEARA8 SHOWN IN THIS MANUAL OR IN SUPPL

4、EMENTSPUBLISHED BY SONY.Harmonic Distortion:IM Distortion:(60 Hz: 7 kHz = 4:1)ATTENTION AU COMPOSANT AVANT RAPPORTApprox.Approx.Approx.10.5 kg (23 lb 2oz). net12.5 kg (27 lb 9 oz), in shipping carton(US, Canadian Model)9.5 kg (21 lb), net11.5 kg (25Ib 6oz), in shipping carton(AEP, UK, E Model)Both c

5、hannels driven simultaneouslyAt 1 kHz5OW+5OW (8nlAt 20 Hz-20 kHz5OW+5OW(SIlAccording to DIN 45500 (AEP, UK, E Model)52W+52W 03.Q)10 Hz-25 kHz30Less than 0.5% at rated outputLess than 0.1 % at 1 W outputLess than 0.5 % at rated outputLess than 0.1% at 1W outputRadioFans.CN 收音机爱 好者资料库1-2. CIRCUIT DESC

6、RIPTIONPROTECTION CIRCUITTwo kinds of protection circuit are employed inthis power amplifier. One is a power-transistorprotection circuit and the other is a speaker pro-tection circuit.1. Power-transistor Protection CircuitTo protect overloaded power transistors fromdestruction, a protection circuit

7、 is employed. Thefusible resistors are inserted in each of Q704,4705 (L-CH) and 4754, 4755 (R-CH) collectorand emitter circuits. When the excessive currentflows into the power transistors, these fusibleresistors break faster than the transistors and thusprotects the transistors from destruction.Spea

8、ker Protection Circuit (See Fig. l-l and Fig. 1-2)When the excessive current flows into the powertransistors, B+ voltage decreases. Therefore, 4301turns on, biasing the base of Q302, and Q302conducts. This removes the bias voltage at thebase of Q306 and Q306 turns off. The relay is not activated by

9、off state of Q306. According-ly, the speaker is cut off from the amplifiercircuit.When the positive dc component presents at thespeaker output terminal, C310 is charged up asshown in Fig. l-2. Q303 turns on, Q306 turns offand the relay RY301 is not activated (4304 re-mains in off condition). Also, w

10、hen the negativedc component presents, C3 11 is charged up. Thisturns 9304 on, Q306 off and RY301 is notactivated (9303 remains in off condition).3.Muting Circuit (See Fig. 1-3 and Fig. 1-4)This muting circuit prevents the loud “pop” (dueto initial current flow) or click noises producedjust after tu

11、rning the POWER switch to on or off.These transients might damage a delicate high-fidelity speaker system.When POWER Switch turned on:C308 commerces to charge through R309. At thesame time, the base voltage of Q306 graduallyrises in accordance with charging voltage of C308.It takes about 3 seconds u

12、ntil Q306 is turned on.Accordingly, the speaker output terminal is cut offby the relay RY301 for about 3 seconds after thePOWER switch is turned on. This protects thespeaker from the destruction caused by the “pop”noises.When POWER Switch turned off:Fig. 1-2.The reverse voltage (about - 1.7 V) that turns offQ306 immediately reduces, and the positive poten-tial is applied to the base of Q305. Q305 turns onand Q306 turns off, cutting off the operation ofRY301. Therefore, no pop noise presents on thespeaker output.POWER Switch :ONFig. l-1.-4-Fig. 1-3.