Sony-BDPS560-bdp-sm 维修电路原理图.pdf

《Sony-BDPS560-bdp-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-BDPS560-bdp-sm 维修电路原理图.pdf（132页珍藏版）》请在收音机爱好者资料库上搜索。

1、Sony CorporationVideo Business GroupSERVICE MANUAL9-890-712-112009F0500-1 2009.6Published by Quality Assurance Dept.BLU-RAY DISC/DVD PLAYERVer. 1.0 2009.06BDP-S560RMT-B104ASPECIFICATIONSUS ModelCanadian ModelSystemLaser: Semiconductor laserInputs and outputs(Jack name:Jack type/Output level/Load imp

2、edance)LINE OUT R-AUDIO-L:Phono jack/2 Vrms/10 kilohmsDIGITAL OUT (OPTICAL):Optical output jack/18 dBm(wave length 660 nm)DIGITAL OUT (COAXIAL):Phono jack/0.5 Vp-p/75 ohmsHDMI OUT:HDMI 19-pin standard connectorCOMPONENT VIDEO OUT (Y, PB, PR):Phono jack/Y: 1.0 Vp-p/PB, PR: 0.7 Vp-p/75 ohmsLINE OUT VI

3、DEO:Phono jack/1.0 Vp-p/75 ohmsLINE OUT S VIDEO:4-pin mini DIN/Y: 1.0 Vp-p, C: 0.286 Vp-p/75 ohmsLAN (100):100BASE-TX TerminalEXT:External memory slot (For connecting the external memory)DC output: 5 V 500 mA MaxUSB:USB jack Type A (For connecting digital still camera and USB memory)WirelessWireless

4、 LAN standard:IEEE802.11a/b/gIEEE802.11n draft 2.0Frequency range:U.S. models:2.4 GHz band: Channels 1-115 GHz band: Channels 36-64, 100-140, 149-165Canada models:2.4 GHz band: Channels 1-115 GHz band: Channels 36-64, 100-116, 132-140, 149-165Modulation:DS-SS Modem and OFDM ModemGeneralPower require

5、ments:120 V AC, 60 HzPower consumption:28 WDimensions (approx.):430 mm 216 mm 70 mm(17 in. 8 5/8 in. 2 13/16 in.)(width/depth/height) incl. projecting partsMass (approx.):2.4 kg (5 lb 4 5/8 oz)Operating temperature:5 C to 35 C (41 F to 95 F)Operating humidity:25 % to 80 %Supplied accessoriesSpecific

6、ations and design are subject to change without notice.? Audio/video cable (phono plug 3) (1)? AC power cord (1)? Remote commander (remote) (1)? Size AA (R6) batteries (2)RadioFans.CN 收音机爱 好者资料库 2 BDP-S560SAFETY CHECK-OUTLEAKAGE TESTThe AC leakage from any exposed metal part to earth ground and from

7、 all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use t

8、hese instruments.2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75V, so analog meters must have an accurate low-v

9、oltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board su

10、rface for solder splashes and bridges.2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommen

11、d their replacement.4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer.6. Check the B+ voltage

12、 to see it is at the values specified.7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.After correcting the original service problem, perform the following safety checks before releasing the set

13、 to the customer:1.5 k0.15 FACvoltmeter(0.75 V)To Exposed MetalParts on SetEarth GroundFig. A. Using an AC voltmeter to check AC leakage.Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circu

14、it boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be appli

15、ed to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, l

16、ess prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.CAUTION:The use of optical instrument with this product will inc

17、rease eye hazard.CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radia-tion exposure.This label is located on the laser protective housing inside the enclosure.WARNING!WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE

18、 EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL PICK-UP BLOCK.SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK ? OR DOTTED LINE WITH MARK ? ON THE SCHE

19、MATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. RE-PLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ? SUR LES DIAGRA

20、MMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPL-MENTS PUBLIS PAR SONY.RadioFans.CN 收音机爱 好者资料库 3 BDP-S560TABLE OF CONTENTSSection Title PageSection Ti

21、tle Page1. SERVICE NOTE1-1. Disc Removal Procedure If The Tray Cannot Be Ejected (Forced Ejection) . 1-11-2. Work when optical device are replaced . 1-11-3. Test Disc . 1-2 1-3-1. Operation and Display . 1-22. DISASSEMBLY2-1. Disassembly Flow . 2-12-2. Upper Case . 2-12-3. Front Panel Block . 2-22-4

22、. BD Drive . 2-32-5. Wireless Lan Card Block . 2-32-6. Rear Panel Block. 2-42-7. MB-127 Board . 2-42-8. Switching Regulator . 2-52-9. Circuit Boards Location . 2-53. BLOCK DIAGRAMS3-1. Overall Block Diagram. 3-13-2. DSP Block Diagram . 3-23-3. AV OUT Block Diagram . 3-33-4. USB/ETHER, FL Block Diagr

23、am . 3-43-5. Power Block Diagram (1/3) . 3-53-6. Power Block Diagram (2/3) . 3-63-7. Power Block Diagram (2/3) . 3-74. SCHEMATIC DIAGRAMS4-1. This Note Is Common For Schematic Diagrams . 4-14-2. Frame Schematic Diagram. 4-24-3. ANT-001 Board (ANTENNA) Schematic Diagram. 4-34-4. ANT-002 Board (ANTENN

24、A) Schematic Diagram. 4-44-5. FL-194 Board (SWITCH) Schematic Diagram . 4-54-6. FR-302 Board (FL DRIVER) Schematic Diagram . 4-64-7. HU-012 Board (USB HUB) Schematic Diagram. 4-74-8. MB-127 Board (EMMA3P DDR2-A) Schematic Diagram (1/14). 4-84-9. MB-127 Board (EMMA3P DDR2-B) Schematic Diagram (2/14).

25、 4-94-10. MB-127 Board (POWER1) Schematic Diagram (3/14). 4-104-11. MB-127 Board (CLK/POWER2) Schematic Diagram (4/14). 4-114-12. MB-127 Board (FLASH/HOST) Schematic Diagram (5/14). 4-124-13. MB-127 Board (USB) Schematic Diagram (6/14). 4-134-14. MB-127 Board (HDMI/SATA) Schematic Diagram (7/14). 4-

26、144-15. MB-127 Board (AUDIO/VIDEO) Schematic Diagram (8/14). 4-154-16. MB-127 Board (GPIO/JTAG) Schematic Diagram (9/14). 4-164-17. MB-127 Board (IPIO) Schematic Diagram (10/14). 4-174-18. MB-127 Board (ETHERNET) Schematic Diagram (11/14) . 4-184-19. MB-127 Board (RF SDRAM) Schematic Diagram (12/14)

27、. 4-194-20. MB-127 Board (DRIVE/RF) Schematic Diagram (13/14). 4-204-21. MB-127 Board (IFD) Schematic Diagram (14/14) . 4-214-22. USB-016 Board (USB REAR CONNECTOR) Schematic Diagram . 4-224-23. USB-017 Board (USB FRONT CONNECTOR) Schematic Diagram . 4-234-24. Waveforms . 4-245. PRINTED WIRING BOARD

28、S5-1. This Note Is Common For Printed Wiring Boards . 5-15-2. ANT-001 Board (ANTENNA) Printed Wiring Board . 5-25-3. ANT-002 Board (ANTENNA) Printed Wiring Board . 5-35-4. FL-194 Board (SWITCH) Printed Wiring Board. 5-45-5. FR-302 Board (FL DRIVER) Printed Wiring Board . 5-55-6. HU-012 Board (USB HU

29、B) Printed Wiring Board . 5-65-7. MB-127 Board (MAIN) Printed Wiring Board (Side A) . 5-75-8. MB-127 Board (MAIN) Printed Wiring Board (Side B) . 5-85-9. USB-016 Board (USB REAR CONNECTOR) Printed Wiring Board . 5-95-10. USB-017 Board (USB FRONT CONNECTOR) Printed Wiring Board . 5-106. IC PIN FUNCTI

30、ON DESCRIPTION . 6-17. SERVICE MODE . 7-18. ERROR LOG LIST . 8-19. TROUBLESHOOTING . 9-110. REPAIR PARTS LIST10-1. Exploded Views . 10-1 10-1-1. Case Section . 10-1 10-1-2. Front/Rear Chassis Section . 10-2 10-1-3. Main Chassis Section . 10-3 10-1-4. BD Section . 10-4 10-1-5. Accessories . 10-510-2.

31、 Electrical Parts List . 10-61-1BDP-S560SECTION 1SERVICE NOTE1-1. DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION)1. Remove the upper case. (Refer to page 2-1)2. Insert a clip in the hole of a drive and open a tray. Note: Use a clip of about 1.2 mm in the diameter1-2. Work when

32、 optical device are replacedNote: Please do the following work when you replace the optical device. 1. Install it in PC after downloading two set of software from following URL. (About the procedure, refer to the attached Readme.txt file) STEP 1 Microsoft .NET Framework Version 2.0 Redistributable P

33、ackage (x86) http:/ STEP 2 Microsoft .NET Framework 2.0 Service Pack 1 (x86) http:/ Take the photograph the part of the bar code of the optical device. (Refer to the following picture) 3. Drag-and-drop the bar code photograph to the icon of decode software (BDBUDec). * The decode software is a compl

34、ete set of “BDBUDec”, “Tasman.Bars.dll”, and “SavePath”. * Because docode software cannot be attached, it separately distributes it.4. Input the password when you start decode software.* Inquire of each service headquarters because the password cannot be disclosed. 5. Write the decode data to the se

35、t. (About the procedure, refer to the attached BU Adjustment flowchart.ppt file)trayclip(Use that of about 1.2 mm in the diameter)hole1-2BDP-S5601-3. TEST DISCPart No.DescriptionLayerJ-6090-199-ABLX-104Single LayerJ-6090-200-ABLX-204Dual Layer3-702-101-01CD (YEDS-18)J-6090-088-AHLX-504Single Layer (

36、NTSC)J-6090-089-AHLX-505Dual Layer (NTSC)J-6090-077-AHLX-506Single Layer (PAL)J-6090-078-AHLX-507Dual Layer (PAL)1-3-1. Operation and DisplayCheck Items1) BLX-104 1. Select 23.976Hz/1080p 2. Play “4.Motion pictures” 3. Check whether player can play back or not 4. Check each outputs Video: Composite/

37、S Video/component/HDMI Audio: Digital out (Coaxial/Optical)/Audio out/5.1Ch output* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) can use instead of 1080/24p. However this is temporary correspondence. 2) BLX-204 1. Select 1080i (59.94Hz or 50Hz) 2. Play “4.Motion pictures” 3. Check wheth

38、er player can play back or not (Check the picture and sound output)3) CD (YEDS-18) Check whether player can play back or not (Check the sound output)4) HLX-504/505 (NTSC), HLX-506/507 (PAL) 1. After displayed Main Menu, select “1.Video” 2. Play “1.Color Bar 100%” (Check the picture and sound output)

39、 3. Return to Menu 4. Play “Demonstration 4:3” or “5.Demonstration 16:9” (Check the picture and sound output)1-3BDP-S5601-3-1-1. BLX-104 Menu Function (1)Main MenuXXXXXXXXXXXXXXXXX XXXXXXXX XX XX XX X1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displ

40、ayed.1-3-1-2. BLX-104 Menu Function (2)Main MenuSub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1To Main Menu after playback of T20_C1To Main Menu after playback of T21_C1Sub_menu3 is displayedTo Main Menu after playback from T54_C1 to T60_C1To Main Menu after playback of T61_C1

41、To Main Menu after playback of T62_C1* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-played.* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively di

42、splayed.* 5. AV Sync does not operate.Note: Txx_ Cxx Chapter No. Title No.1-4BDP-S5601-3-1-3. BLX-104 Menu Function (3)Main MenuTo Main Menu after playback from T23_C1 to T40_C1To Main Menu after playback of T41_C1To Main Menu after playback of T42_C1Sub_menu2 is displayedTo Main Menu after playback

43、 from T44_C1 to T50_C1To Main Menu after playback of T51_C1To Main Menu after playback of T52_C1Sub_menu4 is displayed* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-played.* When returning to Main Menu after playback

44、from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed.* 5. AV Sync does not operate.1-5BDP-S5601-3-1-4. BLX-104 Menu Function (4)Sub menu1X XX XX XX XX XX X1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar

45、 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-tively displayed on Sub menu1 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively displayed on Sub menu1 scree

46、n.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/1080i is selectively displayed.6) Selection of LPCM Audio t Playback from T2_C1 to T19

47、_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.7) Select

48、ion of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu1 after playback. 1. Color Bar 100% is selectivel

49、y displayed on Sub menu1 screen.8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. ColorBar 100% is selectively displayed on Sub menu1 screen.9) At the selection of Main Menu, 1. VideoSignal of 1080/59.94i of Main Menu is selectively displayed.10) AV Sync does not oper

50、ate.1-6BDP-S5601-3-1-5. BLX-104 Menu Function (5)Sub menu2XXXXXX1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is selectively displayed on Sub menu2 s