《Pioneer-M25-pwr-sch 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《Pioneer-M25-pwr-sch 维修电路原理图.pdf(10页珍藏版)》请在收音机爱好者资料库上搜索。
1、 CONTENTS Features. 2 Configuration of the Stereo System. 3 Connection Diagram. 4 Operation. 5 Protective Circuitry . 5 Combinations with the M-25 . 6 Maintenance. 6 Characteristics Charts. 7 Specifications. 8 IMPORTANT NOTICE The serial number for this equipment is located on the bottom plate. Plea
2、se write this serial number on your enclosed warranty card and keep in a secure area. This is for your security. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. RadioFans.CN 收音机爱 好者资料库FEATURES 120W + 120W Power Amplifier with a Wide Frequency Band and Low
3、Distortion The first stage of the M-25 adopts a dual transistor differential amplifier with a current mirror as the load for a superb stability and gain right from the lowest low fre-quencies to the highest high frequencies. The pre-driver stage consists of a voltage amplifier with a constant curren
4、t circuit as the load, and this makes for a significant improvement in the degree of use of the power voltage, and also for a satisfying gain and linearity. The power stage features a Class-AB pure complementary parallel push-pull circuit with a three-stage Darlington connection. A newly developed p
5、ower transistor called a Ring Emitter Transistor (RET) has been introduced into the new Class-AB circuitry. This feature guarantees an ultra wide frequency range which turns the attributes of the RET to maximum advantage, and also a superior low-distortion response whatever the power rating across a
6、n ultra-low to full power spectrum. The M-25 delivers Continuous Power Output of 120 watts* per channel, min., at 8 ohms from 5 Hertz to 30,000 Hertz with no more than 0.01% total harmonic distortion. In particular, the Class-AB SEPP circuit functions as a Class-A circuit which is highly rated on ac
7、count of its hi-fidelity sound reproduction capabilities with low power outputs (up to 3W/8-ohms). This means that you can enjoy the final sound as you would from a Class-A amplifier. Finally, the pre-driver section contains an over-drive limiter and a power limiter for protecting the power transist
8、ors. This helps to greatly improve the reliability. Twin Transformer Power Supply for Excellent Separation The M-25 is symmetrically designed with completely separate heavyweight class power supplies for each channel. Each employs large-capacity capacitors (two 22,000uF for each channel) which not o
9、nly feature excellent regulation but also have plenty of reserve. Along with the wide-band frequency response, they ensure a superior channel separa-tion and a reproduction of sound which is both clear and full of latent energy. There is also a surge-killer circuit to keep the inrush current from th
10、e power transformers as well as the high current which charges the electrolytic capacitors to the bare minimum, and this feature reduces the load on all of the related parts. 2Highly Dependable Protective Circuitry The M-25 employs a relay type of protective circuit which is equipped with a current
11、detector and an overcurrent detector. This circuit is designed to protect the speakers from unforeseen accidents caused by the genera-tion of current in the output, or from shortcircuiting of the speaker terminals owing to faulty contacts, as well as the power transistors by releasing the output cir
12、cuitry momentarily. Moreover, the output circuit relay is for 4-circuit high current uses and all the circuits are connected in parallel for enhanced reliability. This circuitry can also be counted on to perform muting when the power switch is flipped between ON and OFF. Carefully Selected, High-qua
13、lity Parts Each and every part which makes up the M-25 has been singled out for its quality so that only the best is finally chosen. Among the parts employed are gold-plated input and speaker terminals, printed circuit boards of paper epoxy resin with a high insulation resistance, and printed circui
14、t boards using 70u thick copper foil, low-resistance pure copper plates for parallel connections and for the grounding wire, and non-inductive cement resistors. Esthetically Satisfying and Full-bodied Design The visual appeal of the power transistors and heat sinks mounted on a broad-based silver-to
15、ned aluminum die-cast chassis is what you would expect from a top-quality power amplifier. Just one look at the M-25 is enough to convince you of its tremendous power and stability. *Measured pursuant to Federal Trade Commissions Trade Regulation Rule on Power Output Claims for Amplifiers. RadioFans
16、.CN 收音机爱 好者资料库 CONNECTION DIAGRAM Check that the power is off before you proceed with the connec-tions. Always remember to switch the power off if you decide to change the connections while you are using the model. SPEAKER SYSTEM As shown in Fig. 1, connect the R (right) channel speaker to the M-25s
17、 R speaker output terminals, and the L (left) channel speaker to the M-25s L speaker output terminals. Both speakers are clearly marked with plus and minus polarities (red and white, respectively). The M-25s speaker output terminals are similarly marked. Make sure that you connect like poles (plus t
18、o plus, minus to minus). PREAMPLIFIER As shown in Fig. 2, use the accessory connecting cords to connect the stereo preamplifiers output terminals to the M-25s input terminals. The terminal which is closer to you is for the R (right) channel, and the connector furthest away is for the L (left) channe
19、l. OPERATION 1. Set the preamplifiers controls as follows: Set the preamplifiers power switch to OFF. Set the volume control (attenuator) to the lowest position. If your preamplifier has a tape monitor switch, set it to SOURCE (or OFF). Only when playing back a tape should it be set to ON. 2. Set th
20、e M-25 up as follows: Connect the power plug to the power outlet. If you have connected the power plug to the spare power outlet (SWITCHED: capacity of 800W or more) on the preamplifier, you will be able to switch the preamplifier on and off by operating the power switch on the M-25. 3. Beginning op
21、eration Set the power switches on the preamplifier and M-25 to ON. Operate the preamplifier, turntable, tape deck or tuner, and commence play. Adjust the volume and tone with the controls on the preamplifier. PROTECTIVE CIRCUITRY There will be no sound from the speakers for between three and eight s
22、econds after the M-25s power switch has been thrown. This is because the supply of power actuates the muting circuit which is designed to eliminate noise when this switch is thrown. In addition, the protective circuitry is actuated to safeguard the speakers from being damaged in the rare case that D
23、C components enter the output. If the sound suddenly stops coming from the speakers during operation or if you hear the built-in relays being continuously actuated (click, click), this may mean that there is a speaker connection short-circuit or an overload (if you are using speakers with an impedan
24、ce of less than 4 ohms). In such cases, the protective circuitry is automatically actuated, and the transistors and speakers are protected from any damage. Once the trouble is corrected, the protective circuitry will be automatically released, and the M-25 will return to its normal state of operatio
25、n. COMBINATIONS WITH THE M-25 MULTIPLE AMPLIFIER SYSTEM Fig. 3 shows a configuration based on two stereo power amplifiers which are used to drive a pre-amplifier, crossover network and four special speaker systems, all of which are separate buys. The main advantage of the multiple amplifier system i
26、s that it reduces the intermodulation distortion. It does this by dividing the audible frequency range and amplifying each of the sepa-rate frequencies with special stereo amplifiers. The audible frequency range can be split into two or three, in which case the resulting systems are known as 2-way o
27、r 3-way multiple amplifier systems. MAINTENANCE Wipe off any dirt or dust that accumulates on the operating panel or casing with a polishing cloth or dry, soft cloth. Clear out any dust between the fins of the radiator with a brush or similar object. Do not use furniture wax or cleaners. Remember al
28、so to avoid using thinners, benzine, alcohol and any other volatile chemicals since they will corrode the panels. ATTACHING THE NAME PLATE The M-25s name plate is designed so that it can be attached to face you, whichever direction the M-25 is pointing. All you have to do is to turn the M-25 upside
29、down, and remove the screw fastening the name plate with a Phillips screwdriver. Then, attach the plate to that side which you want to face you. Always remember that the M-25 is a heavy piece of equipment and so it should be handled with the greatest of care. Spread some-thing under it when turning
30、it upside down to prevent it from being marked. SPECIFICATIONS Semiconductors Transistors . 55 Diodes. 51 Amplifier Section Circuitry . . . First stage current mirror loaded, Three-stage Darlington, Parallel push-pull, Pure complementary OCL (class AB operation) Continuous Power Output of 120 watts*
31、 per channel, min., at 8 ohms from 5 Hertz to 30,000 Hertz with no more than 0.01 % total harmonic distortion, or 120 watts per channel at 4 ohms from 5 Hertz to 20,000 Hertz with no more than 0.02% total harmonic distortion. Total Harmonic Distortion (20 Hertz to 20,000 Hertz, 8 ohms) Continuous ra
32、ted power output. .No more than 0.0 08% Total Harmonic Distortion (5 Hertz to 30,000 Hertz, 8 ohms) Continuous rated power output. . No more than 0.01% 60 watts per channel power output. . . No more than 0.008% 1 watt per channel power output.No more than 0.008% Intermodulation Distortion (50 Hertz
33、: 7,000 Hertz=4:1) Continuous rated power output . . No more than 0.006% 60 watts per channel power output.No more than 0.005% 1 watt per channel power output.No more than 0.005% Frequency Response . . 5 Hertz to 200,000 Hertz +0/-1dB Input (Sensitivity / Impedance) . 1V/50 kilohms Output Speaker.4
34、ohms to 16 ohms Damping Factor (5 Hertz to 30,000 Hertz, 8 ohms). . . .60 Hum and Noise (IHF, short-circuited, A network) . . 120dB Miscellaneous Power Requirements .120V, 60Hz only Power Consumption. 320 watts (UL) Dimensions.420(W) x 153(H) x 370(D)mm 16-9/16x6-1/32x14-9/16 in. Weight without pack
35、age. 23.5kg; 51 lb 11 oz with package .26.2kg; 57 Ib 10oz Furnished Parts Connection Cord with Pin Plugs . 1 Operating Instructions . 1 *Measured pursuant to Federal Trade Commissions Trade Regulation rule on Power Output Claims for Amplifiers. NOTE: Specifications and the design subject to possible
36、 modifica-tion without notice due to improvements. Circuitry: First stage Current mirror loaded, 3-stage Darlington parallel Push-pull pure complementary OCL (class AB operation) Continuous power output of 120 watts* per channel, min. at 8 ohms from 5 hertz to 30,000 hertz with no more than 0.01% to
37、tal harmonic distortion, or 120 watts* per channel at 4 ohms from 5 hertz to 20,000 hertz with no more than 0.02% total harmonic distortion. Total Harmonic Distortion: No more than 0.008% (20Hz to 20,000Hz, 8 ohms) (continuous rated power output) Total Harmonic Distortion: No more than 0.01% (5Hz to
38、 30,000Hz, 8 ohms) (continuous rated power output) No more than 0.008% (60 watts per channel power output) No more than 0.008% (1 watt per channel power output) Intermodulation Distortion: No more than 0.006% (50Hz:7,000Hz=4:1) (continuous rated power output) No more than 0.005% (60 watts per channe
39、l power output) No more than 0.005% (1 watt per channel power output) Frequency Response: 5 to 20,000Hz +0dB, -1 .0dB Input Sensitivity/Impedance: 1V/50k ohms Output Speaker: 4 ohms to 16 ohms Damping Factor: 60 (5 to 30,000Hz, 8 ohms) Hum and Noise: 120dB (IHF, short-circuited A network) SEMICONDUC
40、TORS Transistors: 55 Diodes: 51 MISCELLANEOUS Power Requirement: 120V 60Hz only Power Consumption: 320 watts (UL) Dimensions: Without package: 16-9/16(W)x 6-1/16(H)x 14-9/16(D) inches 420(W) x 153(H) x 370(D)mm Weight: Without package: 51 Ib. 13oz./23.5kg Measured pursuant to the Federal Trade Commissions Trade Regulation Rule on Power Output Claims for Amplifiers. NOTE: Specifications and design subject to possible modification without notice, at the sole discretion of Series 20.