Fostex-FD4-dm-sm维修电路原理图.pdf

《Fostex-FD4-dm-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Fostex-FD4-dm-sm维修电路原理图.pdf（62页珍藏版）》请在收音机爱好者资料库上搜索。

1、FD-4Service ManualModelDIGITAL MULTITRACKERRadioFans.CN 收音机爱 好者资料库SAFETY INSTRUCTIONSRead instructions - All the safety and operating instruc-tions should be read before the appliance is operated.Retain instructions - The safety and operating instructionsshould be retained for future reference.Heed

2、warnings - All warnings on the appliance and in theoperating instructions should be adhered to.Follow instructions - All operating and use instructionsshould be followed.Water and Moisture - The appliance should not be usednear water - for example, near a bathtub, washbowl,kitchen sink, laundry tub,

3、 in a wet basement, or near aswimming pool, and the like.Carts and Stands - The appliance should be used onlywith a cart or stand that is recommended by the manufac-turer.An appliance and cart combination should be moved withcare. Quick stops, excessive force, and uneven surfacesmay cause the applia

4、nce and cart combination to over-turn.Wall or Ceiling Mounting - The appliance should bemounted to a wall or ceiling only as recommended by themanufacturer.Ventilation - The appliance should be situated so that itslocation or position does not interfere with its proper ven-tilation. For example, the

5、 appliance should not be situ-ated on a bed, sofa, rug, or similar surface that may blockthe ventilation openings; or, placed in a built-in installa-tion, such as a bookcase or cabinet that may impede theflow of air through the ventilation openings.Heat - The appliance should be situated away from h

6、eatsources such as radiators, heat registers, stoves, or otherappliances (including amplifiers) that produce heat.Power Sources - The appliance should be connected to apower supply only of the type described in the operatinginstructions or as marked on the appliance.Grounding or Polarization - The p

7、recautions that shouldbe taken so that the grounding or polarization means ofan appliance is not defeated.Power Cord Protection - Power supply cords should berouted so that they are not likely to be walked on orpinched by items placed upon or against them, payingparticular attention to cords at plug

8、s, convenience recep-tacles, and the point where they exit from the appliance.Cleaning - The appliance should be cleaned only as rec-ommended by the manufacturer.Nonuse Periods - The power cord of the appliance shouldbe unplugged from the outlet when left unused for a longperiod of time.Object and L

9、iquid Entry - Care should be taken so thatobjects do not fall and liquids are not spilled into the en-closure through openings.Damage requiring Service - The appliance should be ser-viced by qualified service personnel when:A.B.C.D.E.Servicing - The user should not attempt to service the ap-pliance

10、beyond that described in the operating instruc-tions. All other servicing should be referred to qualifiedservice personnel.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVIC

11、EABLE PARTS INSIDE.TO PREVENT ELECTRIC SHOCK, MATCHWIDE BLADE OF PLUG TO WIDE SOLT,FULLY INSERT.POUR VITER LES CHOCS LECTRIQUES,INTRODUIRE LA LAME LA PLUS LARGE DELA FICHE DANS LA BORNE CORRE-SPONDANTE DE LA PRISE ET POUSSERJUSQU AU FOND.CAUTION:ATTENTION:The exclamation point within an equilateralt

12、riangle is intended to alert the user to thepresence of important operating and mainte-nance (servicing) instructions in the literatureaccompanying the appliance.The lightening flash with arrowhead symbol,within an equilateral triangle, is intended toalert the user to the presence of uninsulated“dan

13、gerous voltage” within the products en-closure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.“WARNING”“TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS-TURE.”1.2.3.4.5.6.7.8.The power supply cord or the plug has been dam

14、aged;orObjects have fallen, or liquid has been spilled into theappliance; orThe appliance has been exposed to rain; orThe appliance does not appear to operate normally orexhibits a marked changed in performance; orThe appliance has been dropped, or the enclosuredamaged.9.10.11.12.13.14.15.16.17.Radi

15、oFans.CN 收音机爱 好者资料库Parts marked with this sign are safety critical components. They must always be replaced with identicalcomponents. Refer to the Fostex Parts List and ensure exact replacement.CAUTIONTABLE OF CONTENTS1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16、. .2. CONTROLS, INDICATORS AND CONNECTORS . . . . . . . . . . .3. SOFTWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . .4. SERVICE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5. ERROR CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17、 . .6. INSTALLING 2.5 INTERNAL HARD DISK DRIVE . . . . . . . . .7. EXPLODED VIEW, PCB ASSEMBLY AND PARTS LIST . . . . .8. CIRCUIT DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Owners manual: 8288414100 (for export model): 8288415000 (for domestic model)Service mode, error code li

18、st, explode view, PCB assembly, parts list and circuit diagrams are given in thismanual to assist the service technician in maintaining the Model FD-4.NOTESThe following accessories are supplied with FD-4 as the standard accessories.*Following is the packing material for the Model FD-4.*Carton, inne

19、r, FD-4: 8228716000Packing, side, L, FD-4: 8228440000Packing, side, R, FD-4: 8228441000FD-44711 1219202441!FD-434FD-41. SPECIFICATIONSRECORD & REPRODUCERecording MediumExternal fixed / removable hard disk driveStandardSCSI-2 or betterSampling Frequency32 kHz, 44.1 kHzQuantization12-bit nonlinear, 16

20、-bit linearEmphasisNot availableRecording Time (mono track min.)Fs: 32 kHzAbout 33 min. / 100 MB (up to 24 hours) at maximumFs: 44.1 kHzAbout 18 min. / 100 MB (up to 24 hours) at maximumNumber of TracksNORMAL / MASTERING MODE 16 (4 + 2 additional tracks)MASTERING MODE 24Number of simultaneous record

21、ing tracks2Number of simultaneous playback tracks4Number of tracks to be pasted at a time6Recording FormatFDMS-3Recording ModeNORMAL MODE (Fs: 32 kHz, 4 + 2 tracks, default)MASTERING MODE 1 (Fs: 44.1 kHz, 4 + 2 tracks)MASTERING MODE 2 (Fs: 44.1 kHz, 4 tracks)ELECTRICAL (0 dBV = 1 V) MIXER SECTIONRef

22、erence Input LevelMIC-50, -30 dBVImpedance20 k or moreLINE-10 dBVImpedance20 k or moreRECORDER IN-10 dBVImpedance20 k or moreAUX RTN-20 dBVImpedance8 k or moreDATA INConnectorSquare shape opticalFormatIEC consumer optical standard IEC 958 Part 3Reference Output LevelSTEREO-10 dBVLoad impedance10 k o

23、r moreAUX SEND-10 dBVLoad Impedance10 k or moreMONITOR-10 dBVLoad impedance10 k or moreHEADPHONE20 mW at maximum (Load: 16 )50 mW at maximum (Load: 50 )DATA OUTConnectorSquare shape opticalFormatIEC consumer optical standard IEC 958 Part 3FD-45ELECTRICAL (continued)SCSI DATA input / outputConnectorD

24、-SUB 25-pinProtocolSCSI-2, unbalanced transfer methodTransfer typeAsynchronousNumber of device to be connected1Fader / Knob Position at Reference Input / OutputMASTER faderAt 8 9 position (AUX RTN : -20 dBV / 1 kHz, AUX RTNVR: MAX. Adjust master fader for -10 dBV output atSTEREO OUT.)MONITOR knobAdj

25、ust MONITOR knob for -10 dBV output at MONITOROUTPUT. (MON SEL: ST+MON, MON)INPUT faderAt 7 8 position (INPUT: -10 dBV / 1 kHz, EQ GAIN: 0,PAN: L (R). Adjust input fader for -10 dBV output atSTEREO OUT.)Output LevelINPUT (1 4) AUX SEND-10 dBV +0, -2 dB (INPUT: -10 dBV / 1 kHz, EQ GAIN:0, PAN: L (R),

26、 AUX1, 2 VR: CH MAX, input fader: at 7 8 position.)INPUT (1 4) MONITOR-10 dBV 1 dB (INPUT: -10 dBV / 1 kHz, EQ GAIN: 0,PAN: L (R), MON VR: MON MAX, MON PAN: L (R),input fader: at 7 8 position.)Frequency ResponseINPUT (1 4) MONITOR20 20 kHz +1, -3 dB (INPUT: -50 dBV)20 20 kHz +1, -2 dB (INPUT: -10 dB

27、V)INPUT (1 4) AUX SEND20 20 kHz +1, -2 dB (INPUT: -10 dBV)AUX RTN MONITOR OUT20 20 kHz +1, -2 dB (AUX RTN: -20 dBV)AUX RTN PHONES80 20 kHz +1, -2 dB (AUX RTN: -20 dBV, at 20 mW /16 )EQ CharacteristicsHigh (12 kHz) & Low (80 Hz)+15 dB 3 dB at “+15” position -15 dB 3 dB at “-15” positionMid (200 Hz 5

28、kHz)+15 dB 3 dB at “+15” position -15 dB 3 dB at “-15” positionS / NINPUTINPUT 4Residual Noise-50 dBV-38 dBV-10 dBV+2 dBV-50 dBV-38 dBV-10 dBV+2 dBVVR MINAUX SENDAUX SENDAUX SENDAUX SENDMONITORMONITORMONITORMONITORPHONES-10 dBV+2 dBV-10 dBV+2 dBV-10 dBV+2 dBV-10 dBV+2 dBV66 dB or more78 dB or more80

29、 dB or more92 dB or more63 dB or more75 dB or more73 dB or more85 dB or more68 dB or more80 dB or more82 dB or more94 dB or more65 dB or more77 dB or more75 dB or more87 dB or more-75 dBV or lessLEVELLEVELUNWTD.AWTD.INPUTOUTPUTS / N6FD-4ELECTRICAL (continued)DistortionCrosstalk60 dB or more / 1 kHzC

30、lick NoisePower on / off-20 dBV p-p or lessOther switching-50 dBV p-p or lessMIDI ControllingOperation check should be executed using the test modewith connecting the MIDI IN and OUT terminal. RECORDER SECTIONFrequency ResponseFs: 44.1 kHz20 20 kHz +1, -2 dBFs: 32 kHz20 14.5 kHz +1, -2 dBFull Scale

31、Output Level (Ref: -12dB)+2 dBV 1 dB (Fs: 32 kHz / 44.1 kHz)Dynamic Range88 dB or more (Fs: 32 kHz / 44.1 kHz)Total Harmonic DistortionFs: 44.1 kHz0.02 % or lessFs: 32 kHz0.08 % or lessChannel Separation80 dB or more / 1 kHz at max. recording level (Fs: 32 kHz / 44.1 kHz)S / N88 dB or more (A-WTD.,

32、Fs: 32 kHz / 44.1 kHz)Power ConsumptionJPN13 W +5, -20 %Others15 W +5, -20 %Specifications and appearance are subject to change without notice for product improvement.INPUTAUX RTN-40 dBV0 dBV0 dBV-10 dBV-10 dBVMONITORMONITORAUX SENDMONITORPHONES0 dBV0 dBV0 dBV0 dBV20 mW100 10 kHz100 10 kHz100 10 kHz

33、100 10 kHz1 kHz0.05 % or less0.05 % or less0.05 % or less0.05 % or less0.10 % or lessLEVELLEVELUNWTD.AWTD.INPUTOUTPUTS / NFD-472. CONTROLS, INDICATORS & CONNECTORS4321INPUT 3R MON OUT LR ST OUT LAUX RTN 1RMONO/LAUX RTN 2RMONO/L2 AUX SEND 14 INSERT 3INPUT 4SCSIOUTINDATARRECORDER INLINMIDIOUTPUNCHIN/O

34、UTDATAMIDIPOWERRear PanelControl PanelFront PanelMON LMON RMON LMON RMON LMON RMON LMON R00000000000000000000UNDO/PUNCHAUTOLEVELLEVELMASTER01020101010SELECTORPANLOWHIGHGAINMIDAUX1-AUX2+TRK4INPUTRLPANLOWHIGHGAINMIDAUX1-AUX2+TRK3INPUTRLPANLOWHIGHGAINMIDAUX1-AUX2+TRK2INPUTRLPANLOWHIGH2k900300GAINMIDSHI

35、FTAUX1-200-AUX2+5k+TRK1INPUT0105L/R+MONL/RMONOFFINPUTTRK 4OFFINPUTTRK 3OFFINPUTTRK 2OFFPITCHVARIMIDRLSHIFT4/R3/L2/RSELDISP SELRLDIGITAL MULTITRACKER1/LINPUTTRK 1CLIPBOARD PLAYLOCATE ABS 0LOCATE REC ENDF FWD/REWIND/PLAYSTOPRECORDREDOEDITSTARTINOUTAUTO PLAYEXECUTE/YESEXIT/NOHOLD/STOREENDINOUTPGM SELAU

36、TO RTNSETUPHMLHMLTIME BASEACCESS2k900300SHIFT2005kMID2k900300SHIFT2005kMID2k900300SHIFT2005kMIDAUXAUXAUXAUXAUX RTNEQEQEQEQMONMONMONMONPANPANPANPANINPUT SELINPUT SELINPUT SELINPUT SEL1234L/RMON SECTIONCLIPBOARDAUTO PUNCHAUTO RTNADD. TRACKPREVIEWRECORD TRACKP. EDITSHUTTLEJOGEJECTLOC MEMLOCATE010501050

37、10501058FD-4Control Panel (Mixer Section)MON LMON RMON LMON RMON LMON RMON LMON R00000000000000000000LEVELLEVELMASTER01020101010SELECTORPANLOWHIGHGAINMIDAUX1-AUX2+TRK4INPUTRLPANLOWHIGHGAINMIDAUX1-AUX2+TRK3INPUTRLPANLOWHIGHGAINMIDAUX1-AUX2+TRK2INPUTRLPANLOWHIGH2k900300GAINMIDSHIFTAUX1-200-AUX2+5k+TRK

38、1INPUT0105L/R+MONL/RMONOFFINPUTTRK 4OFFINPUTTRK 3OFFINPUTTRK 2OFFMIDRLINPUTTRK 1HMLHML2k900300SHIFT2005kMID2k900300SHIFT2005kMID2k900300SHIFT2005kMIDAUXAUXAUXAUXAUX RTNEQEQEQEQMONMONMONMONPANPANPANPANINPUT SELINPUT SELINPUT SELINPUT SEL1234L/RMON SECTION01050105010501051. Input faders 1-42. Input se

39、lect switchesINPUT SEL (INPUT/OFF/TRK)3. Panpot knobs PAN (L/R)4. Monitor panpot knobs PAN (MON L/MON R)5. Monitor level control knob MON (INPUT/TRK)6. Equalizer control knobs EQ (HIGH/MID/LOW)7. AUX send knobs AUX (AUX 1/AUX 2)8. AUX return knobs AUX RTN (1, 2)9. Monitor master knobMONITOR SECTION

40、(MASTER)10. Monitor select switchSELECTOR (L/R, L/R+MON, MON)11. Master fader L/R12. Input level switches LEVEL (H/M/L)12345768910111212FD-4913. Record track select keysRECORD TRACK (1/L, 2/R, 3/L, 4/R, L, R)14. LCD15. Contrast adjustment knob16. Display indication select key17. Setup key SETUP18. T

41、ime Base select key19. Execute/Yes key EXECUTE/YES20. Exit/No key EXIT/NO/ EJECT 21. Access LED ACCESS22. JOG dial JOG/ SHUTTLE 23. Fast forward button F FWD/ 24. Rewind button REWIND/ 25. Play button PLAY26. Stop button STOP27. Record button RECORD/ AUTO PUNCH 28. Shift key SHIFT 29. Vari Pitch key

42、 VARI PITCH/ P.EDIT 30. Auto Return/Auto Play mode on/off keyAUTO RTN/AUTO PLAY31. Locate key LOCATE/ LOC MEM 32. Hold/ key HOLD/ 33. Store key STORE34. Undo/Redo key UNDO/REDO35. Edit key EDIT36. Auto Return Start key AUTO RTN START/ PREVIEW 37. Auto Return End key AUTO RTN END/ PREVIEW 38. Auto Pu

43、nch In key AUTO PUNCH IN/ PREVIEW 39. Auto Punch Out key AUTO PUNCH OUT/ PREVIEW 40. Clipboard In key CLIPBOARD IN/ PREVIEW 41. Clipboard Out key CLIPBOARD OUT/ PREVIEW 2627282930313235333436383937131441401516171819202122232425Control Panel (Recorder Section)UNDO/PUNCHAUTOPITCHVARIRLSHIFT4/R3/L2/RSE

44、LDISP SELDIGITAL MULTITRACKER1/LCLIPBOARD PLAYLOCATE ABS 0LOCATE REC ENDF FWD/REWIND/PLAYSTOPRECORDREDOEDITSTARTINOUTAUTO PLAYEXECUTE/YESEXIT/NOHOLD/STOREENDINOUTPGM SELAUTO RTNSETUPTIME BASEACCESSCLIPBOARDAUTO PUNCHAUTO RTNADD. TRACKPREVIEWRECORD TRACKP. EDITSHUTTLEJOGEJECTLOC MEMLOCATE10FD-4Front

45、PanelRear Panel1. Monitor Out jacks MON OUT L, R (RCA pin)2. Stereo Out jacks ST. OUT L, R (RCA pin)3. AUX Send jacks 1, 2 AUX SEND 1, 2 (Phone)4. AUX Return jacks 1, 2 AUX RTN 1, 2 (Phone)5. Insert jacks 3, 4 INSERT 3, 4 (TRS Phone)6. Balanced input connectors 3, 4 INPUT 3, 4(Balanced XLR)7. Record

46、er in jacks L, R RECORDER IN L, R(RCA pin)1. Input jacks 1, 2, 3, 4 (Phone)2. Headphone jack PHONES (TRS Phone)8. MIDI OUT jack MIDI OUT (DIN 5-pin)9. MIDI IN jack MIDI IN (DIN 5-pin)10. Punch in/out jack PUNCH IN/OUT (Phone)11. Data output jack DATA OUT (OPTICAL)12. Data input jack DATA IN (OPTICAL

47、)13. SCSI connector SCSI (D-SUB 25-pin)14. Power cable15. Power switch POWERINPUT 3R MON OUT LR ST OUT LAUX RTN 1RMONO/LAUX RTN 2RMONO/L2 AUX SEND 14 INSERT 3INPUT 4SCSIOUTINDATARRECORDER INLINMIDIOUTPUNCHIN/OUTDATAMIDIPOWER345891011121314157612432112FD-4113. SOFTWARE UPDATEThe FD-4 software can be

48、updated through SCSI port. This means that unscrewing and opening up the FD-4 top panel is notnecessary to change the EPROMs on the MAIN PCB assy. Please refer to the following explanation for correct softwareupdating procedures.Updated software in a removable media (e.g. floppy disk, zip disk, etc.

49、) to be sent via airmailUpdated software as an attachment file to be sent via E-mailThere are two ways of sending the FD-4 updated software.3-1. Method of Sending Software from Fostex Japan1.2.3-2. Required ToolsIBM PC compatible computer with SCSI boardRemovable type SCSI driveCable between the rem

50、ovable type SCSI drive and the SCSI boardCable between the removable type SCSI drive and the FD-4 (D-SUB 25-pin)The following tools/equipment are required to update the FD-4 software.3-3. Software Updating ProceduresConnect the removable type SCSI drive to the SCSI board.Insert the diskette to the r