Denon-DND9000-cd-sm维修电路原理图.pdf

《Denon-DND9000-cd-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Denon-DND9000-cd-sm维修电路原理图.pdf（97页珍藏版）》请在收音机爱好者资料库上搜索。

1、Hi-Fi ComponentSERVICE MANUALMODELDN-D9000DOUBLE CD PLAYER?Some illustrations using in this service manual are slightly different from the actual set.For U.S.A., Canada,Europe & Asia model16-11, YUSHIMA 3-CHOME, BUNKYOU-KU, TOKYO 113-0034 JAPANTelephone: 03 (3837) 5321X0139 NC 0203RadioFans.CN 收音机爱

2、好者资料库2DN-D9000SPECIFICATIONSGENERALType:Twin mechanism compact disc player with wired remote controlDisc Type:Standard compact discs (12 cm and 8 cm discs)For CD-R and CD-RW discs, only finalized ones can be played back.However, some discs may not be playable depending on their recordingconditions.D

3、imensions:Player unit:482 (W) 88 (H) 252 (D) mm (without feet)18-31/32 (W) 3-15/32 (H) 9-59/64 (D)Remote control unit:482 (W) 62 (H) 40 (D) mm (without feet)18-31/32 (W) 2-7/16 (H) 1-37/64 (D)Installation:19-inch rack mountablePlayer unit:2URemote control unit:3UPlayer unit:8 kg (17 lbs. 10.2oz)Remo

4、te control unit:4 kg (8 lbs. 13.1oz)Power Supply:U.S.A. & Canada model:120 V AC10 %, 60 HzEurope & Asia model:230 V AC10 %, 50 HzPower Consumption:33 WEnvironmental Conditions:Operational temperature:5 to 35 C (41 to 95 F)Operational humidity:25 to 85 % (no condensation)Storage temperature:20 to 60

5、C (4 to 140 F)AUDIO SECTIONMain out/Monitor outQuantization:24-bit linear per channelSampling Frequency:44.1 kHz at normal pitchOversampling Rate:8 timesTotal Harmonic Distortion:0.01 % or lessS/N Ratio:90 dB or moreChannel Separation:85 dB or moreFrequency Response:20 to 20,000 HzAnalog outputMain

6、Out Level:2.0 VrmsMonitor Out Level:2.0 VrmsDigital Output:Signal Format:SPDIF (6 dB)Output Level:0.5 Vp-p 75 /ohmsLoad Impedance:10 k/kohms or moreFUNCTIONSInstant Start:Within 20 msec.Variable PitchMain, Track:4 % (0.05 % pitch), 10 % (0.1 % pitch), 16 % (0.1 % pitch),24 % (0.1 % pitch), 100 % (1

7、% pitch)Pitch Bend:Pitch range:4 %, 10 % : 12 %Pitch range:16 %, 24 %: 26 %Pitch range:100 %: 99 %SAMPLERSampling:44.1 kHzLength:15 secOutput Level:2.0 Vrms (Variable/14+6 dB)Variable Pitch:24 % (0.1 % pitch)Search Precision:1/75 sec (1 subcode frame)Max. Scan Speed:Over 20 times normal speedMax. Me

8、mo Memory Steps:5,000 stepsSAFETY PRECAUTIONSThe following check should be performed for the continued protection of the customer and service technician.LEAKAGE CURRENT CHECKBefore returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassisresis

9、tance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of thepower cord is less than 460 kohms, the unit is defective.RadioFans.CN 收音机爱 好者资料库3DN-D9000Drive Unit2. Top Cover1) Remove 4 screws 2 and 2 screws 3.2) Detach Top Cover.243. Front Panel Un

10、it1) Remove 7 screws 4 and pull out Front Panel Unit.Top Cover112Front Panel UnitMain Unit1. Drive Unit1) Remove 4 screws 1 and pull out Drive Unit.2) Disconnect Flat cable and Connector.3) Detach Drive Unit.Note: Pull at a straight angle to avoid Flat Cable damage. Do not fail to pull AC cord from

11、wall outlet before disconnectthe Flat Cable and Connector. If AC cord is remainedplugged into wall outlet, power is kept supplied in the unit,which may cause danger.DISASSEMBLY (Follow the procedure below in reverse order when reassembling)Drive UnitFlat CableConnector334444DN-D90004. Drive Cover1)

12、Remove 5 screws 5 and pull out Drive Cover.5. Drive1) Move Drive Rack in arrow direction through the hole onthe bottom chassis. Loader Frame comes out.2) Pull up Loader Panel while pulling it towards front.3) Remove 4 screws 6 and pull out Drive.Drive Panel6Drive RackLoader Panel6Loader FrameDriveDr

13、ive Cover555DN-D9000Remote Control Unit1. Top Cover1) Remove 7 screws 7 and pull out Top Cover.7Top Cover2. Cover1) Disconnect Connector.2) Remove 2 screws 8 and pull out Cover.ConnectorCover83. Sensor Unit1) Remove 2 screws 9 and pull out Sensor Cover.2) Detach Sensor Unit.9Sensor CoverSensor Unit6

14、DN-D9000Wheel UnitSet Screw6. Inner Panel Unit1) Remove 4 screws ? ? and pull out Knob (MARU) andFader Knob.2) Remove 4 screws ? ? and pull out Inner Panel Unit.5. Jog Dial Unit1) Remove a E ring ? ? and pull out Jog Dial Unit.4. Wheel Unit1) Remove Set Screw and pull out Wheel Unit.? ? ? ?Jog Dial

15、UnitKnob (MARU)Fader KnobInner Panel Unit? ?7DN-D900043215678DCBAEBLOCK DIAGRAMRC-D90DN-D9000CD1 FL tube outTFS0LRCKmain1 outFLT DriverML9207TCK0BCLKAMP10FG-9000ADDRESSTXD0AMAIN18CHCD1DRIVE1TXD0BMON1D/Amon1 outPCM1608AMP11ATAPIINTERFACEmain2 outAMP20mon2 outAMP21TMP86CM47UROM32kRAM1kLED outKey scan1

16、6Bit BusTCK1DITVR inATAPIBUSselectTXD1ADOUT1SM5902JOGinterfacedigital outCPU DSPBUS8bit BusinterfaceRC112V5.0VJOG1DRIVERJOG1DRIVER5.0VRC2JOG2JOG23.3VXEFFECTData07FADER15.0VHB8.0VFADER2F1/F212.0V12V5.0V8.0VCPU DSPaddress CD2BUSHBinterfacedata4MMEMOFL tube outATAPIFLASH MEMORYFG-9000interfaceDRIVE216B

17、it BusATAPITFS0LRCKINTERFACETCK0BCLKTXD0AMAIN2TXD0BMON2ADDRESSTMP86CM47UROM32kRAM1kLED outKey scanVR inJOGTFS1DIT2TCK1SM5902TXD1ADOUT2digital out128MBSDRAM128MBSDRAMLEDdriveBU2090FLT1384fsDMAATAP InterfaceCPUSYSTEMCPUTMP86CM47UMN102H730FRAM10KRC/FLT PowerDC-DC ConverterATAP InterfaceCPUTMP86CM47U4MF

18、LASH MEMORY(DSP BOOT)DMA128MBFLT2ADSP21065LSDRAMDSP2RAM ControlEFFECTORSHOCK PROOF128MBSDRAM+12.0VSWITCHINGREGULATORBUSselectD0D15D16D31RAM ControlEFFECTORADSP21065LDSP1SHOCK PROOFD6D31D0D15TFS1COM1COM2COM3Control SignalAddressCOM4comFLT DriverML9207CD1com8bit BusLEDdriveBU2090D9000_Block.p6502/03/1

19、4, 18:35Page 7Adobe PageMaker 6.5J/Win8DN-D9000Required Measuring Implement1. Reference disc (TCD784 or CO-74176)1. What is Service ProgramService program is a special program intended for confirming servo functions etc.CONFIRMING THE SERVO2. Contents of Service ProgramSwitch on the power while push

20、ing the CD1s PITCH BEND + button and CD2s CUE button at the same time. Afteractuating the servo program, select an aiming process number with the SELECT knob, A1 button, A2 button, or A3 button.Press the SELECT knob to execute the selected process, the process number is then displayed on the track i

21、ndicator of thedisplay. To exit from the service program, just switch off the power.Process No.(TRACKIndication)Function(Character-display)Contents01?com Version check(Version No.)Check Version with JOG dial.1. System ?com version No.: “Sys_XXXX”2. DSP soft version No.: “Dsp_XXXX”3. ATAPI ?com versi

22、on No.: “Atapi_XXXX”4. RC ?com version No.: “Rc_XXXX”5. ROM drive mecha. ?com version No.: “Drive_XXXX”02OPEN/CLOSE(Open Close)Performs open/close each time when the SELECT knob is pushed.03Drive Diagnostic(Drive_Diag)ROM drive performs operation check when the SELECT knob is pushed, andindicates th

23、e operational result. If the disc holder open, it starts the operation checkafter closing. It indicates “Normal_End” if it ends normal. In case of error, ROMdrive error code is displayed in the characters lower portion as “E?”.04Drive Data Read(Data Read)Starts continuous playback at its maximum rea

24、ding speed from the beginning ofdisc when the SELECT knob is pushed. It halts reading and stops if the knob ispushed again.05Error Code Check(Error Data)Turn the JOG dial to display the logging error codes in the occurred order.(“Error Data” is displayed.)10 error logs are memorized at maximum.Kinds

25、 of Error Code, displayedError Code Table (Appears only at Heat Run and Chucking Test function)Pressing SELECT knob enters to data erase mode. (“Err Clear?” is displayed.)If the SELECT knob is pushed again, the memorized error data are cleared.06Total Running Time(Total_Time)Total time span of servo

26、 function that counted by the hour is displayed.(“Total Time” is displayed.)The display time is less than 65535 hours.Note: No time is counted if powered down within 59 minutes.Pressing SELECT knob enters to data erase mode. (“Time Clear?” is displayed.)If the SELECT knob is pushed again, the memori

27、zed time data are cleared.SELECT knob07AutomaticServo AdjustmentcallStarts automatic servo adjustment when the SELECT knob is pushed, and aftercompleting the adjustment, sort of the used disc is indicated. Data is selectable withthe JOG dial.1. Disc check, CD/CD-RW2. Focus gain data3. Focus balance

28、data4. Focus offset data5. Tracking gain data6. Tracking balance data7. Tracking offset data8. PreAMP Tracking Sensor Gain9. DSP Tracking Sensor Gain10. PI offset9DN-D9000Adjustment?ItemAdjustment Value?indication?atcharacter portions.1Focus Gain35 1202Focus Balance?20 ?203Focus Offset?20 ?204Tracki

29、ng Gain35 1205Tracking Balance?20 ?206Tracking Offset?20 ?20* Reference data.Process No.(TRACKIndication)Function(Character-display)ContentsA1 button?Heat Run(H/R1_Normal)Starting with the PLAY/PAUSE button, it repeats open/close of the tray andplayback.All tracks are played back if the track count

30、is less than 20. Only the first and lasttracks are played back if the tracks are more than 21. When any errors, it stopsand indicates error code (see Error Code Table).A2 button?Chucking Test(H/R2_Tray)Starting with the PLAY/PAUSE button, it repeats open/close of the tray, servo on,and TOC read.The

31、display shows the number of the tray operation. When any errors, it stops andindicates error code (see Error Code Table).A3 button?System check(Sys._Check)It starts system check when the PLAY/PAUSE button is pushed, and indicates thestatus by performing plain operational check in the system .1. Comm

32、unication judge between the system ?com and DSP2. DSP SDRAM write/read operation check3. Communication judge between the system ?com and ATAPI ?com4. Communication judge between the ATAPI ?com and ROM drive5. ROM drive operation check6. D/A register write/read operation check7. DIT register write/re

33、ad operation checkAfter finishing the check, it indicates the result on the character display lowerportion.When the 1. 7. items are OK, their item numbers are indicated.But if there is a NG item, its item number is not indicated.3. TEST MODE4. Error Code Table (Appears only at Heat Run and Chucking

34、Test function)Error CodeContentsE1 00E1 01E1 03E1 04E1 05E1 06Automatic Adjustment ErrorUnable to detect discUnable to adjust tracking offsetUnable to adjust focus fine gainUnable to actuate focusUnable to actuate trackingUnable to adjust tracking fine gainE2 02Servo down during automatic adjustment

35、E3 00Unable to read TOCE4 00E4 01Unable to close the disc holder in the regular timeUnable to open the disc holder in the regular timeE5 00Slide error10DN-D9000Detailed error can be displayed by JOG dial when error occurs.Error IndicationTRMINSECFRAMCHARACTERDisplays the trackNo. in which erroroccur

36、red.Displays the time at which error occurred.“H ? E ?”Operation countError code5. System com and DSP Version UpgradeSystem com and DSP can be upgraded in the following manner.Version Upgrade Method1. Record the version upgrade software on a CD-R or CD-RW disc, only as one file with the format ISO96

37、60 Mode-1.The file name of the supplied version upgrade software should be used as is and this disc needs to finalize.2. After loading the disc made in above step 1 into CD1, turn off the power. Then, turn on the power while pressing theOPEN/CLOSE button of CD1. The version upgrade starts with readi

38、ng data of the disc. No disc should be loaded intoCD2.3. TRAY LED of both CD1 and CD2 will turn on when the version upgrade starts, and they will turn off when the versionupgrade ends.? TRAY LED of both CD1 and CD2 will blink if the version upgrade ends abnormally due to error etc.? In case of some

39、error or the power is turned off during the version upgrade, it may be impossible to operate at allthereafter. Changing of IC502 on GU-3412 is necessary in this case, and software writing to IC502 should be donebeforehand.4. Turn off the power after finishing the version upgrade, and turn on again t

40、o take out the disc.5. File name of the upgrade software indicates version numbers.6. ROM Drive (FG-9000) com Version UpgradeDrive (FG-9000) com can be upgraded in the following manner.Version Upgrade Method1. Record the version upgrade software on a CD-R or CD-RW disc, only as one file with the for

41、mat ISO9660 Mode-1.The file name of the supplied version upgrade software should be used as is and this disc needs to finalize.2. After turning on the power, load the disc made in above step 1 into the mecha. you want to upgrade the version.3. “Drive” and “Version UP?” are indicated in the character

42、 display. Press the OPEN/CLOSE button and remove the discwhen not upgrade the version.4. Press the PLAY/PAUSE to start the version upgrade. “Now Loading” is indicated.5. When the version upgrade is finished, “Complete” is indicated and the tray opens.6. Turn off the power once and turn on again afte

43、r take out the disc.?The version upgrade ends in 2030 seconds normally. If the power turned off underway or the version upgrade endsabnormally, the drive may become malfunction. In such a case, version upgrade with PC will be needed.7. File name of the upgrade software indicates version number.File

44、name D9 ? ? . BINSystem ?com versionDSP versionFile name FG9K ? . BINVersion number11DN-D90001283397641329665TOP VIEWSEMICONDUCTORS? ? ? ? ? ICsNote: Indication before IC Numbers denotes P.W.B. name.FG : CD-ROM P.W.B. UnitDS : DSP P.W.B. UnitPO : Power P.W.B. UnitRC : Remote P.W.B. UnitMN102H730F (D

45、S: IC501)MN102H730F Terminal FunctionFunctionI/OPinNo.Pin NameSymbol1CS0_CS0_OPuExt. memory chip select 0 (Flash ROM CS)2CS1_CS1_OPuExt. memory chip select 1 (Flash ROM for memo)3D00DQ0I/OExt. memory data in/output 0, DSP interface 04D01DQ1I/OExt. memory data in/output 1, DSP interface 15D02DQ2I/OEx

46、t. memory data in/output 2, DSP interface 26D03DQ3I/OExt. memory data in/output 3, DSP interface 37VDDVDDPower (+3.3V)8VSSVSSGND9D04DQ4I/OExt. memory data in/output 4, DSP interface 410D05DQ5I/OExt. memory data in/output 5, DSP interface 511D06DQ6I/OExt. memory data in/output 6, DSP interface 612D07

47、DQ7I/OExt. memory data in/output 7, DSP interface 713D08,P10KEYIN2IPuHHOPEN/CLOSE2 key input14D09,P11KEYIN1IPuHHOPEN/CLOSE1 key input15D10,P12FPLAY1IPuHHCD1 fader start PLAY input16PD0,DMAACK1_FCUE1IPuHHCD1 fader start CUE input17PD1,DMAREQ1_FPLAY2IPuHHCD2 fader start PLAY input18D11,P13FCUE2IPuHHCD

48、2 fader start CUE input19D12,P14JOGA2I(Pu)HHJOGA pulse input for CD2 scratch (Direction detect)20D13,P15JOGB2I(Pu)HHJOGB pulse input for CD2 scratch (Direction detect)21D14,P16JOGA1IPuHHJOGA pulse input for CD1 scratch (Direction detect)22D15,P17JOGB1IPuHHJOGB pulse input for CD1 scratch (Direction

49、detect)23WORDWORDIData bus width select (H: 8bit), VDD fixed24VDDVDDPower (+3.3V)25MODEMODEILLProcessor mode, GND fixedDETExtIniRes12DN-D9000FunctionI/OPinNo.Pin NameSymbolDETExtIniRes26PC3MUTEOPuHHMute signal (H: Mute)27XIXIIOscillation input28XOXOOOscillation output29VDDVDDPower (+3.3V)30OSCIOSCII

50、Oscillation input, 32.0MHz31OSCOOSCOOOscillation output32VSSVSSGND33BOSC32.0MHzOSystem clock output34PC5,NMI_RESERVEIPuHH35RST_RST_Icom reset36PC0LEDOUT1OPuHHTRAY1 LED37P76LEDOUT2OPuHHTRAY2 LED38P60,IRQ0JOGINT1I(Pu)HHJOGA pulse input for CD1 scratch39P61,IRQ1JOGINT2I(Pu)HHJOGA pulse input for CD2 sc