JVC-DRDX5SE-dvd-sm 维修电路原理图.pdf

《JVC-DRDX5SE-dvd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-DRDX5SE-dvd-sm 维修电路原理图.pdf（116页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2005 VICTOR COMPANY OF JAPAN, LIMITEDNo.YD0852005/11Mini DV & HDD & DVD VIDEO RECORDERYD085200511DR-DX5SEK, DR-DX5SEL, DR-DX5SEU,DR-DX5SEY, DR-DX5SEZTABLE OF CONTENTS1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2、 . . . . . . . . . . . . . . . . . . . . . . . 1-32SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-63DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3、. . . . . . . . . . . . . . . . . . . . . . . 1-84ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-115TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4、. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35STANDBY/ ONDV/HDD/DVDS-VIDEOVIDEO(MONO)LA UDIORDV HDD DVD DV IN/OUTDISPLAYSELECTVHSREC MODEPRF1DV/HDDRAM/RWDR-DX5SEK, DR-DX5SEL, DR-DX5SEU, DR-DX5SEY, DR-DX5SEZ D5MC21DVHDDDVDDVDCABLE/SATTVDVDPRNEXTPREVIOUSPAUSERECREC MODEREMAINDISPLAYON SCRE

5、ENSLOWSLOWPLAY/SELECTSTOP/CLEARNAVIGATIONTOP MENURETURNENTERMENUTV/CBL/SATSTANDBY/ONTVTVAVVIDEOTVAUXCANCELMEMO/MARKPROGRAMMEEDITDUBBINGLIVEJUMPSET UPSATAUDIOSUBTITLEVPS/PDCANGLELIVE CHECKPROGRESSIVESCAN(EL, EU, EY, EZ model)(EK model)RadioFans.CN 收音机爱 好者资料库1-2 (No.YD085)SPECIFICATION Specifications

6、shown are for SP mode unless otherwise specified. E.& O.E. Design and specifications subject to change without notice. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. DTS and DTS Digital Out are trademarks of Digital Theater Sys

7、tems, Inc. SHOWVIEW is a trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Devel-opment Corporation.(EL, EU, EY, EZ MODEL) VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manuf

8、actured underlicense from Gemstar Development Corporation.(EK MODEL) (i.Link) refers to the IEEE1394-1995 industry specification and extensions thereof. The logo is used for products compliant with the i.Link stan-dard.DR-DX5SEKDR-DX5SEL/EU/EY/EZGENERALPower requirementAC 220 V 240 V, 50 Hz/60 HzPow

9、er consumptionPower on45 WPower off15 WTemperatureOperating5C to 35CStorage-20C to 60COperating positionHorizontal onlyDimensions (W H D)435 mm 96 mm 383 mmWeight6.5 kgInput/OutputVideo input0.5 - 2.0 Vp-p, 75 (pin jack)Audio input-8 dB, 50 k (pin jack), Corresponding to mono (left)Audio output-8 dB

10、, 1 k (pin jack)21-pin SCART connectorsIN/OUT 1, IN/DECODER 1S-video inputY: 0.8 - 1.2 Vp-p, 75 , C: 0.2 - 0.4 Vp-p, 75 S-video outputY: 1.0 Vp-p, 75 , C: 0.3 Vp-p, 75 DV4-pin for DV IN/OUTComponent video outputY: 1.0 Vp-p, 75 , CB/CR, PB/PR: 0.7 Vp-p, 75 Corresponding to copy protectionDigital audi

11、o outputOptical, CoaxialCorresponding to Dolby Digital and DTS Digital SurroundBit stream Selectable in digital audio output setting menuVIDEO/AUDIO (DVD Deck)Recording timeMaximum 8 hours (with 4.7 GB disc) (XP): Approx. 1 hour, (SP): Approx. 2 hours, (LP): Approx. 4 hours (EP): Approx. 6 hours, (F

12、R): Approx. 1 hour - 8 hoursAudio recording systemDolby Digital (2 ch), Linear PCM (XP mode only)Video recording compression systemMPEG2 (CBR/VBR)VIDEO/AUDIO (HDD Deck)Video recording compression systemMPEG2 (VBR)Audio recording systemDolby Digital (2 ch), Linear PCM (XP mode only)Recording timeMaxi

13、mum 473 hours (with 250 GB HDD)(XP): Approx. 53 hours, (SP): Approx. 109 hours, (LP): Approx. 218 hours(EP): Approx. 328 hours, (FR): Approx. 473 hoursVIDEO/AUDIO (DV Deck)Signal systemPAL colour signal, 625 lines/50 fieldsRecording systemDigital Component RecordingFormatDV format (SD mode)CassetteM

14、ini DV CassetteMaximum recording time(SP)(SP): 80 min. with M-DV80ME cassette(LP)(LP): 120 min. with M-DV80ME cassetteAudio recording systemPCM 48 kHz, 16 bit (2 ch)/32 kHz, 12 bit (4 ch)TUNER/TIMERTuning systemFrequency synthesized tunerChannel coverageVHF : 44.5 MHz - 143 MHz/143 MHz - 470 MHzUHF

15、: 470 MHz - 862 MHzVHF : 47 MHz - 89 MHz/104 MHz - 300 MHz/302 MHz - 470 MHzUHF : 470 MHz - 862 MHzMemory backup timeApprox. 60 minutesACCESSORIESProvided accessoriesRF cable, 21-pin SCART cable,Infrared remote control unit, AA/R6 battery 2RadioFans.CN 收音机爱 好者资料库(No.YD085)1-3SECTION 1PRECAUTION1.1SA

16、FTY PRECAUTIONSPrior to shipment from the factory, JVC products are strictly in-spected to conform with the recognized product safety and elec-trical codes of the countries in which they are to besold.However,in order to maintain such compliance, it is equallyimportant to implement the following pre

17、cautions when a set isbeing serviced.1.1.1Precautions during Servicing(1) Locations requiring special caution are denoted by labelsand inscriptions on the cabinet, chassis and certain parts ofthe product.When performing service, be sure to read andcomply with these and other cautionary notices appea

18、ringin the operation and service manuals.(2) Parts identified by the symbol and shaded ( ) partsare critical for safety.Replace only with specified part numbers.NOTE :Parts in this category also include those specified tocomply with X-ray emission standards for productsusing cathode ray tubes and th

19、ose specified forcompliance with various regulations regarding spu-rious radiation emission.(3) Fuse replacement caution notice.Caution for continued protection against fire hazard.Replace only with same type and rated fuse(s) as speci-fied.(4) Use specified internal wiring. Note especially: Wires c

20、overed with PVC tubing Double insulated wires High voltage leads(5) Use specified insulating materials for hazardous live parts.Note especially: Insulation Tape PVC tubing Spacers Insulation sheets for transistors Barrier(6) When replacing AC primary side components (transformers,power cords, noise

21、blocking capacitors, etc.) wrap ends ofwires securely about the terminals before soldering.Fig.1-1-1(7) Observe that wires do not contact heat producing parts(heatsinks, oxide metal film resistors, fusible resistors, etc.)(8) Check that replaced wires do not contact sharp edged orpointed parts.(9) W

22、hen a power cord has been replaced, check that 10-15kg of force in any direction will not loosen it.Fig.1-1-2(10) Also check areas surrounding repaired locations.(11) Products using cathode ray tubes (CRTs)In regard to suchproducts, the cathode ray tubes themselves, the high volt-age circuits, and r

23、elated circuits are specified for compli-ance with recognized codes pertaining to X-ray emission.Consequently, when servicing these products, replace thecathode ray tubes and other parts with only the specifiedparts. Under no circumstances attempt to modify these cir-cuits.Unauthorized modification

24、can increase the high volt-age value and cause X-ray emission from the cathode raytube.(12) Crimp type wire connectorIn such cases as when replacingthe power transformer in sets where the connections be-tween the power cord and power trans former primary leadwires are performed using crimp type conn

25、ectors, if replac-ing the connectors is unavoidable, in order to prevent safe-ty hazards, perform carefully and precisely according to thefollowing steps. Connector part number :E03830-001 Required tool : Connector crimping tool of the propertype which will not damage insulated parts. Replacement pr

26、ocedurea) Remove the old connector by cutting the wires at apoint close to the connector.Important : Do not re-use a connector (discard it).Fig.1-1-3b) Strip about 15 mm of the insulation from the endsof the wires. If the wires are stranded, twist thestrands to avoid frayed conductors.Fig.1-1-4c) Al

27、ign the lengths of the wires to be connected. In-sert the wires fully into the connector.Fig.1-1-5d) As shown in Fig.1-1-6, use the crimping tool tocrimp the metal sleeve at the center position. Besure to crimp fully to the complete closure of thetool.Fig.1-1-6e) Check the four points noted in Fig.1

28、-1-7.Fig.1-1-7Power cordcut close to connector15 mmConnectorMetal sleeve1.252.05.5Crimping toolNot easily pulled freeCrimped at approx. centerof metal sleeveConductors extendedWire insulation recessedmore than 4 mm1-4 (No.YD085)1.1.2Safety Check after ServicingExamine the area surrounding the repair

29、ed location for damageor deterioration. Observe that screws, parts and wires have beenreturned to original positions, Afterwards, perform the followingtests and confirm the specified values in order to verify compli-ance with safety standards.(1) Insulation resistance testConfirm the specified insul

30、ation resistance or greater be-tween power cord plug prongs and externally exposedparts of the set (RF terminals, antenna terminals, video andaudio input and output terminals, microphone jacks, ear-phone jacks, etc.).See table 1 below.(2) Dielectric strength testConfirm specified dielectric strength

31、 or greater betweenpower cord plug prongs and exposed accessible parts ofthe set (RF terminals, antenna terminals, video and audioinput and output terminals, microphone jacks, earphonejacks, etc.). See Fig.1-1-11 below.(3) Clearance distanceWhen replacing primary circuit components, confirm spec-ifi

32、ed clearance distance (d), (d) between soldered termi-nals, and between terminals and surrounding metallicparts. See Fig.1-1-11 below.Fig.1-1-8(4) Leakage current testConfirm specified or lower leakage current between earthground/power cord plug prongs and externally exposed ac-cessible parts (RF te

33、rminals, antenna terminals, video andaudio input and output terminals, microphone jacks, ear-phone jacks, etc.).Measuring Method : (Power ON)Insert load Z betweenearth ground/power cord plug prongs and externally ex-posed accessible parts. Use an AC voltmeter to measureacross both terminals of load

34、Z. See Fig.1-1-9 and follow-ing Fig.1-1-12.Fig.1-1-9(5) Grounding (Class 1 model only)Confirm specified or lower grounding impedance betweenearth pin in AC inlet and externally exposed accessibleparts (Video in, Video out, Audio in, Audio out or Fixingscrew etc.).Measuring Method:Connect milli ohm m

35、eter between earth pin in AC inlet andexposed accessible parts. See Fig.1-1-10 and groundingspecifications.Fig.1-1-10Fig.1-1-11Fig.1-1-12NOTE :These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.ChassisPower cord primary

36、wireddabcVAExternallyexposedaccessible partZExposed accessible partGrounding SpecificationsAC inletRegionUSA & CanadaEurope & AustraliaGrounding Impedance (Z)Z0.1 ohmZ0.5 ohmEarth pinMIlli ohm meterAC Line VoltageRegionJapanEurope & AustraliaR 1 M /500 V DCUSA & Canada1 M R 12 M /500 V DCR 10 M /500

37、 V DCInsulation Resistance (R)Dielectric StrengthClearance Distance (d), (d)100 V100 to 240 V110 to 130 V110 to 130 V200 to 240 VAC 1 kV 1 minuteAC 1.5 kV 1 minuteAC 1 kV 1 minute(Class )(Class )AC 3 kV 1 minuteAC 1.5 kV 1 minuted, d 3 mmd, d 4 mmd, d 3.2 mmd 8 mm (Power cord)d 6 mm (Primary wire)d

38、4 mmAC Line VoltageRegionJapanEurope & AustraliaUSA & CanadaLoad ZLeakage Current (i)a, b, c100 V110 to 130 V110 to 130 V220 to 240 Vi 1 mA rmsi 0.5 mA rmsi 0.7 mA peaki 2 mA dci 0.7 mA peaki 2 mA dcExposed accessible partsExposed accessible partsAntenna earth terminalsOther terminals11.52500.15(No.

39、YD085)1-51.2Hard Disk Drive (HDD) Handling PrecautionsThe HDD is a precision device for use in reading and writing a large amount of data on or from a disk rotating at a high speed. If it isnot handled carefully, either abnormal operation may result or it may not be possible to read data. The HDD is

40、 sensitive to the followingitems and special care is required in safeguarding against them when handling an HDD. Also take care in handling a set incorporatingan HDD.(1) Vibrations and impacts(2) Static electricity(3) Rough handling1.2.1Handling in transport, etc. Be sure to place the HDD in the man

41、ufacturers specified pack-age carton before transport. When receiving a package containing an HDD, check that thepackage carton is not damaged (such as having holes in thecarton, crushed corners, etc.). Do not impact the packaging carton when loading or unloadingit. It is not permitted to use the in

42、ner package carton only fortransporting an HDD. Do not stack package cartons one upon another.1.2.2Handling an HDD in the stand-alone status When handling an HDD on a hard workbench, place an anti-static mat (rubber sheet) or similar object on the hard surface(to prevent any impacts occurring betwee

43、n the HDD andbench). Do not stack the HDDs one upon another. Do not knock an HDD with a hard object (such as a screwdriv-er). Do not place an HDD on its side panel without using a support(do not place an HDD in an unstable position).1.2.3Handling the installation of an HDD Place antistatic mats or s

44、imilar sheets on all of the surfaces on which work is conducted or when the HDD is transported. Do not permit the HDD to knock against the sets brackets. When screwing the brackets, be careful not to knock the HDD. When using a power screwdriver, use a low-shock model and arrangethe tightening torqu

45、e properly. When mounting an HDD in a main body, take care not to apply excessive force to the brackets.HDDDo not throw or drop packages.Be sure to package and transport the HDDs correctly.1-6 (No.YD085)SECTION 2SPECIFIC SERVICE INSTRUCTIONS2.1Different table of featuresThe following table indicates

46、 main different points between models DR-DX5SEK and DR-DX5SEL/EU/EY/EZ.2.2Service positionThis unit has been designed so that the Mechanism and Mainboard assemblies can be removed together from the bottomchassis. Before diagnosing or servicing the circuit boards, takeout the major parts from the bot

47、tom chassis.2.2.1How to set the Service position(1) Refer to the disassembly procedure and perform the disas-sembly of the major parts before removing the Mechanismassembly.(2) Remove the screws that fix the Mechanism, Main board as-sembly to the bottom chassis. If any other screws are usedto fix th

48、e boards, remove them also.(3) Remove the combined Mechanism, HDD, DVD unit,switching regulator, digital, DV jack, junction and Mainboard assemblies.(4) If any other major parts are used, remove them also.(5) Connect the wires and connectors of the major parts thathave been removed in steps (1) to (

49、4). (Refer to Fig. 2-2a.)(6) Place the combined Mechanism, Main board and otherboard assemblies upside down.(7) Insert the power cord plug into the power outlet and thenproceed with the diagnostics and servicing of the board as-sembly.Notes: Before inserting the power cord plug into the power out-le

50、t, make sure that none of the electrical parts are ableto short-circuit between the workbench and the boardassembly. For the disassembly procedure of the major parts anddetails of the precautions to be taken, see Removingthe major parts. If there are wire connections from the Main board andMechanism