NAD-T572-cd-sm 维修电路原理图.pdf

《NAD-T572-cd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《NAD-T572-cd-sm 维修电路原理图.pdf（67页珍藏版）》请在收音机爱好者资料库上搜索。

1、NADSERVICE MANUALT 572T 572DVD / VCD / CDPLAYERDVD / VCD / CDPLAYERDRAFT DATE: 30 OCT, 2002RadioFans.CN 收音机爱 好者资料库CONTENTSSECTION 1 . . . . SUMMARYSECTION 2 . . . . CABINET & MAIN CHASSISSECTION 3 . . . . ELECTRICALSECTION 4 . . . . MECHANISMSECTION 5 . . . . REPLACEMENT PARTS LISTRadioFans.CN 收音机爱

2、好者资料库SECTION 1SUMMARYCONTENTSPRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS . 1-2SERVICING PRECAUTIONS . 1-3 GENERAL SERVICING PRECAUTIONS INSULATION CHECKING PRODEDURE ELECTROSTATICALLY SENSITIVE DEVICES1-2CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY,NEVER PERFORM CUSTOMIZED I

3、NSTALLATIONS WITHOUT MANUFAC-TURERS APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLYVOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANYRESULTING PROPERTY DAMAGE OR USER INJURY.SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARETHOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETYCHECKS AND

4、 SERVICING GUIDELINES. TO DO OTHERWISE,INCREASES THE RISK OF POTENTIAL HAZARDS AND INJURY TO THEUSER.WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTEC-TION FROM A.C. LINE SHOCK.SAFETY CHECKSAFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED. ACHECK SHOULD BE MADE OF THE FOLLOWING.SUBJECT :

5、 FIRE & SHOCK HAZARD1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAYAS TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS.THIS IS ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARETRANSPORTED TO AND FROM THE REPAIR SHOP.2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICESSUCH AS INSULATORS

6、, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER SUPPLY CORDS, AND OTHER HARDWARE HAVEBEEN REINSTALLED PER ORIGINAL DESIGN. BE SURE THAT THESAFETY PURPOSE OF THE POLARIZED LINE PLUG HAS NOT BEENDEFEATED.3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLDSOLDER JOINTS, SOLDER SPLASHES OR SHARP

7、 SOLDER POINTS.BE CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATIONTO PARTS AND COMPONENTS, FOR FRAYED LEADS, DAMAGEDINSULATION (INCLUDING A.C. CORD), AND REPLACE IF NECESSARY.FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS.5. NO LEAD OR COMPONENT

8、SHOULD TOUCH A RECIVING TUBE ORA RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUNDPROTRUDING METAL SURFACES MUST BE AVOIDED.6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOFRESISTORS, CAPACITORS, ETC. MUST BE REPLACED WITH EXACTFACTORY TYPES, DO NOT USE REPLACEMENT COMPONENTSOTHER THAN THOSE

9、SPECIFIED OR MAKE UNRECOMMENDED CIR-CUIT MODIFICATIONS.7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN A.C.LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF THE CABI-NET, (THE CHANNEL SELECTOR KNOB, ANTENNA TERMINALS. HAN-DLE AND SCREWS) TO BE SURE THE SET IS SAFE TO OPERATEWITHOUT DANGER OF ELECTRICA

10、L SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER DURING THIS TEST USE AN A.C. VOLT-METER, HAVING 5000 OHMS PER VOLT OR MORE SENSITIVITY, INTHE FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT RESIS-TOR, PARALLELED BY A .15 MFD. 150.V A.C TYPE CAPACITORBETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE, CON-D

11、UIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUGAND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED 75VOLTS R.M.S. THIS CORRESPO

12、NDS TO 0.5 MILLIAMP A.C ANYVALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCKHAZARD AND MUST BE CORRECTED IMMEDIATELY.SUBJECT: GRAPHIC SYMBOLSTHE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHINAN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THESERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED“DANGE

13、ROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAG-NITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIAN-GLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TOTHE PRESENCE OF IMPORTANT SAFETY INFORMATION INSERVICE LITERATURE.SUBJECT : X-RADIATION1. BE SURE PROCEDURES AN

14、D INSTRUCTIONS TO ALL SERVICE PER-SONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTEN-TIAL SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PIC-TURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHENTHE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN IN THE APPLICABLE

15、SCHEMATIC. OPERA-TION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PIC-TURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER CERTAIN CIR-CUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF DESIR-ABLE LEVELS.2. ONLY FACTORY SPECIFIED C.R.T. ANODE CONNECTORS MUST BEUSED. DEGAUSSING SHIELDS ALSO SERVE AS AN X-RAY SH

16、IELD INCOLOR SETS, ALWAYS RE-INSTALL THEM.3. IT IS ESSNTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE ANACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRA-TION OF THE METER SHOULD BE CHECKED PERIODICALLYAGAINST A REFERENCE STANDARD, SUCH AS THE ONE AVAILABLEAT YOUR DISTRIBUTOR.4. WHEN THE HIGH VOLTAG

17、E CIRCUITRY IS OPERATING PROPERLYTHERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERYTIME A COLOR CHASSIS IS SERVICED. THE BRIGHTNESS SHOULDBE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGEWITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOESNOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGUL

18、ATINGCORRECTLY. WE SUGGEST THAT YOU AND YOUR SERVICE ORGA-NIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGU-LATION IS ALWAYS CHECKED AS A STANDARD SERVICING PROCE-DURE AND THAT THE HIGH VOLTAGE READING BE RECORDED ONEACH CUSTOMERS INVOICE.5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS INA P

19、RODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE,AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE ANDTHE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCTLONGER THAN IT IS NECESSARY TO LOCATE THE CAUSE OF EXCES-SIVE VOLTAGE.6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES DESCRIBED IN THE APPRO

20、PRIATE SCHEMATIC AND DIAGRAMS(WHERE USED).SUBJECT: IMPLOSION1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTE-GRAL IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BETAKEN TO AVOID DAMAGE DURING INSTALLATION, AVOIDSCRATCHING THE TUBE. IF SCRATCHED REPLACE IT.2. USE ONLY RECOMMENDED FACTORY RE

21、PLACEMENT TUBES.SUBJECT : TIPS ON PROPER INSTALLATION1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBY-HOLE OR CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TOHEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW.2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIOINSTALLATIONS WHERE DEW IS A FAC

22、TOR, NEAR STEAM RADIA-TORS WHERE STEAM LEAKAGE IS A FACTOR, ETC.3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REARVENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DEC-ORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHTOBSTRUCT VENTILATION.4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMER-CIAL MO

23、UNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF ORPLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENTTHICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM. BOLTS OR SCREWS USED FOR FASTENERSMUST NOT TOUCH ANY PARTS OR WIRING. PERF

24、ORM LEAKAGETEST ON CUSTOMIZED INSTALLATIONS.5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ONSLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT ISPROPERLY SECURED.6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITSMOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZ-ARDS OF TRYING

25、 TO ROLL A CART WITH SMALL CASTERS ACROSSTHRESHOLDS OR DEEP PILE CARPETS.7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STANDWHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.S OFTHE SAME

26、OR LARGER SCREEN SIZE.8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS. EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SIN-GLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TOHOME AND FAMILY.PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTSA.C. VOLTMETERGOOD EARTH GROUNDSUCH AS THE WA

27、TERPIPE. CONDUIT. ETCPLACE THIS PROBEON EACH EXPOSEDMETAL PART1-3SERVICING PRECAUTIONSCAUTION : Before servicing the DVD covered by this servicedata and its supplements and ADDENDUMS, read and fol-low the SAFETY PRECAUTIONS. NOTE : if unforeseen cir-cumstances create conflict between the following s

28、ervicingprecautions and any of the safety precautions in this publi-cations, always follow the safety precautions.Remember Safety First:General Servicing Precautions1. Always unplug the DVD AC power cord from the ACpower source before:(1)Removing or reinstalling any component, circuit board, module,

29、 or any other assembly.(2)Disconnection or reconnecting any internal electricalplug or other electrical connection.(3)Connecting a test substitute in parallel with an elec-trolytic capacitor.Caution : A wrong part substitution or incorrect polarity installation of electrolytic capacitors may resulti

30、n an explosion hazard.2. Do not spray chemicals on or near this DVD or any ofits assemblies.3. Unless specified otherwise in this service data, cleanelectrical contacts by applying an appropriate contact cleaning solution to the contacts with a pipe cleaner,cotton-tipped swab, or comparable soft app

31、licator.Unless specified otherwise in this service data, lubricationof contacts is not required.4. Do not defeat any plug/socket B+ voltage interlocks withwhitch instruments covered by this service manual mightbe equipped.5. Do not apply AC power to this DVD and/or any of itselectrical assemblies un

32、less all solid-state device heatsinks are cerrectly installed.6. Always connect test instrument ground lead to theappropriate ground before connection the test instrumentpositive lead. Always remove the test instrument ground lead last.Insulation Checking ProcedureDisconnect the attachment plug from

33、 the AC outlet and turnthe power on. Connect an insulation resistance meter(500V)to the blades of the attachment plug. The insulation resis-tance between each blade of the attachment plug and acces-sible conductive parts (Note 1) should be more than 1M-ohm.Note 1 : Accessible Conductive Parts includ

34、ing Metal pan-els, Input terminals, Earphone jacks, etc.Electrostatically Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damagedeasily by static electricity. Such components commonly arecalled Electrostatically Sensitive (ES) Devices. Examples oftypical ES devices are integrat

35、ed circuits and some fieldeffect transistors and semiconductor chip components.The following techniques should be used to help reduce theincidence of component damage caused by static electricity.1. Immediately before handling any semiconductor compo-nent or semiconductor-equipped assembly, drain of

36、f anyelectrostatic charge on your body by touching a knownearth ground. Alternatively, obtain and wear a commer-cially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly

37、 equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a GROUNDED-tip soldering iron to solder orunsolder ES devices.4. Use only an anti-static solder removal device. Somesolder remo

38、val devices not classified a “anti-static” cangenerate electrical charges sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These cangenerate electrical charge sufficient to damage ESdevices.6. Do not remove a replacement ES device from its protective package until immediately

39、 before you are ready toinstall it. (Most replacement ES devices are packaged withleads electrically shorted together by conductive foam,aluminum foil, or comparable conductive material).7. Immediately before removing the protective material fromthe leads of a replacement ES device, touch the protec

40、tivematerial to the chassis or circuit assembly into which thedevice will be installed.Caution : Be sure no power is applied to the chassis orcircuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Normally harmless motion such a

41、s the brushing together of your clothes fabric or the liftingof your foot from a carpeted floor can generate static elec-tricity sufficient to damage an ES device.)5SPECIFICATIONS GENERALPower requirementsAC120V, 60HzPower consumption14WDimensions(approx.)430 x 118 x 408mm (16.9 X 4.7 X 16.1 inches)

42、(wxhxd) Mass(approx.)5.7kg(12.6 lbs)Operating temperature5C to 40C (41F to 104F)Operating humidity5 % to 90 % SYSTEMLaserSemiconductor laser, wavelength 650nmSignal systemNTSCFrequency responseDVD (PCM 96kHz): 8Hz to 44kHzDVD (PCM 48kHz): 8Hz to 22kHzCD: 8Hz to 20kHzSignal-to-noise ratioMore than 10

43、0dB (ANALOG OUT connectors only)Harmonic distortionLess than 0.008%Dynamic rangeMore than 100dB(DVD)More than 95dB(CD) OUTPUTSVIDEO OUTPUTS1Vp-p, 75 ohms, sync negative, RCA jack x 1S-V IDEO OUTPUTS(Y)1.0V(p-p), 75, negative sync., Mini DIN 4-pin x 1(C)0.3V(p-p), 75 ohmsCOMPONENT VIDEO OUT(Y)1.0V(p-

44、p), 75, negative sync., RCA jack x 1(PB)/(PR)0.7V(p-p), 75 , RCA jack x 2Audio output(digital audio)0.5V(p-p), 75, RCA jack X 1Audio output(optical audio)0.5V(p-p), 75,Optical connector x 1Audio output(analog audio)2.0Vrms (1kHz, 0dB), 330, RCA jack (L, R) x 22-1SECTION 2CABINET & MAIN CHASSISCONTEN

45、TS1. DISASSEMBLY.2-2CABINET DISASSEMBLY .2-2CIRCUIT BOARD DISASSEMBLY .2-32. EXPLODED VIEWS.2-41. Cabinet and Main Frame Section.2-42. Packing Accessory Section.2-62-2DISASSEMBLYCAUTION BEFORE STARTING SERVICINGElectronic parts are susceptible to static electricity and may easily damaged, so do not

46、forget to take aproper grounding treatment as required.Many screws are used inside the unit. To prevent missing, dropping, etc. of the screws, always use amagnetized screw driver in servicing. Several kinds of screws are used and some of them need specialcautions. That is, take care of the tapping s

47、crews securing molded patrs and fine pitch screws used to securemetal parts. If they are used improperly, the screw holes will be easily damaged and the parts can not be fixed.Top Case(A)(A)(A)(A)(A)(A)(A)Disc TrayTray DoorFront PanelStopperStopperCABINET DISASSEMBLY1. Top Case1. Release 7 screws (A

48、). (See Fig. 2-1)2. Lift the top case with holding the back of it,and remove it in the direction of the arrow.Fig. 2-1Fig. 2-2Fig. 2-33. Front Panel1. Eject the disc tray. (See Fig. 2-2)2. Remove the tray door. (See Fig. 2-2)3. Pull the front panel toward you while pressing5 stoppers to disengage, a

49、nd remove the frontpanel. (See Fig. 2-3)2.Tray Door1.Eject the disc tray. 2.Lift up the tray door in the direction of thearrow.2-3(L1)(L1)(B)(B)(C)(C)(C)Power CodePowerCircuitBoardMain ChassisMA Assy Dpm1Bracket MainJack Circuit Board(F)(F)(F)(F)Main Circuit Board(B)(B)(D)(E)(D)(D)(D)(E)(E)(B)(B)(G)

50、(G)(G)(G)(G)(G)Fig. 2-4Fig. 2-51. Disassemble Main circuit board, Jackcircuit board, Power circuit board andMD Assy DPM1. 1. Remove the top case.(See Fig. 2-1)2. Remove 10 screws (B).3. Disassemble Main circuit board and Jack circuitboard from Bracket Main.4. Unscrew 3 screws(C) at Bracket Main.5. D