Sony-CDPCX355-cd-sm 维修电路原理图.pdf

《Sony-CDPCX355-cd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Sony-CDPCX355-cd-sm 维修电路原理图.pdf（72页珍藏版）》请在收音机爱好者资料库上搜索。

1、CDP-CX355US ModelCanadian ModelAEP ModelUK ModelE ModelAustralian ModelSERVICE MANUALCOMPACT DISC PLAYERSony CorporationHome Audio CompanyPublished by Sony Engineering Corporation9-873-551-012002B1600-1 2002.02SPECIFICATIONSVer 1.0 2002. 02Model Name Using Similar MechanismNEWCD Mechanism TypeCDM54-

2、K1BD45Base Unit TypeBU-K1BD45Optical Pick-up TypeKSS-213BFNCompact disc playerLaserSemiconductor laser ( = 780 nm)Emission duration: continuousLaser outputMax 44.6 W* This output is the value measured ata distance of 200 mm from theobjective lens surface on the OpticalPick-up block with 7 mm apertur

3、e.Frequency response20 Hz to 20 kHz 0.5 dBSignal-to-noise ratioMore than 107 dBDynamic rangeMore than 86 dBHarmonic distortionLess than 0.009 %Channel separationMore than 100 dBOutputsANALOG OUTDIGITAL OUT(OPTICAL)GeneralWhere purchasedUSA and CanadianAustraliaLoad impedanceOver 10 kilohmsWave lengt

4、h: 660 nmMaximumoutputlevel2 V(at 50 kilohms)18 dBmJacktypePhonojacksOpticaloutputconnectorPower consumptionsPower requirements120 V AC, 60 Hz13 W14 W13 W13 W240 V AC, 50/60 HzEurope and Asia230 V AC, 50/60 HzOther countriesDimensions (approx.)430 189 493 mm(w/h/d)(17 7 1/2 19 3/8 in.)incl. projecti

5、ng partsMass (approx.)8.5 kg (18 lbs 12 oz)Supplied accessoriesDesign and specifications are subject to change without notice. Audio cord (1) Remote commander (remote) (1) Size AA (R6) batteries (2)120 V AC, 50/60 HzRadioFans.CN 收音机爱 好者资料库2This appliance is classified as a CLASS 1 LASER product. The

6、CLASS 1 LASER PRODUCT MARKING is located on the rearexterior.The following caution label is located inside the unit.Laser component in this product is capableof emitting radiation exceeding the limit forClass 1.CAUTIONUse of controls or adjustments or performance of proceduresother than those specif

7、ied herein may result in hazardous radiationexposure.Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may bedamaged by heat.Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270Cduring repai

8、ring. Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times). Be careful not to apply force on the conductor when solderingor unsoldering.CDP-CX355SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS

9、AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHMATIQUES ET LA

10、 LISTE DES PICES SONTCRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PISES SONYDONT LES NUMROS SONT DONNS DANS CE MANUEL OUDANS LES SUPPMENTS PUBLIS PAR SONY. After correcting the original service problem, perform thefollowing safety checks before releasing the set

11、 to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage. Check leakage asdescribed below.LEAKAGE The AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having a

12、return to chassis, must not exceed 0.5 mA (500 microamperes).Leakage current can be measured by any one of three methods.1.A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers instructions to use theseinstruments.2.A battery-operated AC milliammeter. The Data

13、Precision 245digital multimeter is suitable for this job.3.Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63Trd are examples ofa pas

14、sive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2V AC range are suitable. (SeeFig. A)SAFETY CHECK-OUTTo Exposed Metal Parts on Set0.15 F1.5 kACVoltmeter(0.75 V)Earth GroundFig. A. Using an AC voltmeter to check AC leakage.MODEL IDENTIFICATION BACK PANEL PART NO.

15、PARTS No.MODEL4-238-109-04-238-109-14-238-109-24-238-109-34-238-109-44-238-109-5USCanadianAEP, UKSingaporeAustralianERadioFans.CN 收音机爱 好者资料库3CDP-CX355TABLE OF CONTENTSSECTION 1SERVICING NOTENOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer

16、 electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepain parts.The flexible boar

17、d is easily damaged and should be handled withcare.NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more

18、 than 30 cm away from the objective lens.The emission check enables continuous checking of the S curve.LASER DIODE AND FOCUS SEARCH OPERATIONCHECKCarry out the “S curve check” in “CD section adjustment” and checkthat the S curve waveform is output three times.1. SERVICING NOTE32. GENERAL63. DISASSEM

19、BLY 73-1. Case 83-2. Bracket (F. W. ) 83-3. Front Panel Assy 93-4. DISP Board, JOG Board, KEYBOARD Board 93-5. LED Board, Guide (Door. T) 103-6. Table (300) Assy, Cover (P.T.) 103-7. D. MOTOR Board, Door Motor Assy (M83) 113-8. D. SW Board123-9. Base (Door, Gear) Assy 133-10. Pop-up Assy 133-11. D.

20、SENS (OUT) Board 143-12. T. SENS Board 143-13. D. SENS (IN) Board 153-14. Back Panel Section 153-15. MAIN Board, JACK Board 163-16. POWER Board 163-17. Bracket (Top) , BU Assy 173-18. BU Holder Assy 173-19. BD Board, Optical Device (KSM-213 BFN) 183-20. L. SW (A) Board, L. SW (B) Board 193-21. CDM A

21、ssy 203-22. Motor Assy (Loading) (M82) ,Motor Assy (Table) (M81) , L. T. MOTOR Board 204. SERVICE MODE 215. TEST MODE 255-1. ADJ Mode255-2. Key and Display Check Mode 256. ADJUSTMENTS 266-1. Mechanical Adjustments 266-2. Electrical Adjustment 287. DIAGRAMS 317-1. Block Diagrams BD Section 32 MAIN Se

22、ction 337-2. Printed Wiring Board BD Section 347-3. Schematic Diagram BD Section 357-4. Printed Wiring Board MAIN Section 367-5. Schematic Diagram MAIN Section (1/2) 377-6. Schematic Diagram MAIN Section (2/2) 387-7. Printed Wiring Board T.SENS Section 397-8. Printed Wiring Board D.SENS (IN) Section

23、 397-9. Printed Wiring Board D.SENS (OUT) Section 397-10. Schematic Diagram SENSOR Section 397-11. Printed Wiring Board DISPLAY Section 407-12. Schematic Diagram DISPLAY Section 417-13. Printed Wiring Board JOG Section 427-14. Schematic Diagram JOG Section 437-15. Printed Wiring Board POWER Section

24、447-16. Schematic Diagram POWER Section 447-17. Printed Wiring Board JACK Section 457-18. Schematic Diagram JACK Section 457-19. Printed Wiring Board SWITCH/MOTOR Section 467-20. Schematic Diagram SWITCH/MOTOR Section 467-21. IC Pin Functions 508. EXPLODED VIEWS 548-1. Case Section 548-2. Chassis Se

25、ction 1 558-3. Chassis Section 2 568-4. Back Panel Section 578-5. Front Panel Section 588-6. Mechanism Section 1 (CDM54-K1BD45)(Pop-up Assy, Base (Door. Gear) Assy) 598-7. Mechanism Section 2 (CDM54-K1BD45) 608-8. Mechanism Section 3 (CDM54-K1BD45) 618-9. Mechanism Section 4 (CDM54-K1BD45) 628-10. O

26、ptical Pick-up Section (BU-K1BD45) 639. ELECTRICAL PARTS LIST644CDP-CX355CD-TEXT TEST DISCThis unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube.The CD-TEXT TEST DISC (TGCS-313:J-2501-126-A) is used for checking the display.To check, pe

27、rform the following procedure.Checking Method:1.Turn ON the power, set the disc on the disc table with the side labeled as “test disc” as the right side, close the front cover, and chuck thedisc.2.The following will be displayed on the fluorescent indicator tube. (The display switches each time the

28、TIME/TEXT button is pressed.)Display : CD TEXT TEST DISC (Album Title)3.Press the button and play back the disc.4.The following will be displayed on the fluorescent indicator tube. (If nothing is displayed, press the TIME/TEXT button.)Display : 1kHz/0 dB/ L&R5.Rotate and knob to switch the track. Th

29、e text data of each track will be displayed.For details of the displayed contents for each track, refer to “Table 1 : CD-TEXT TEST DISC Text Data Contents” and “Table 2 : CD-TEXT TEST DISC Recorded Contents and Display”.Restrictions in CD-TEXT DisplayIn this unit, some special characters will not be

30、 displayed properly. These will be displayed as a space or a character resembling it. For details,refer to “Table 2 : CD-TEXT DISC Recorded Contents and Display”.Table 1 : CD-TEXT TEST DISC Text Data Contents (TRACKS No. 1 to 41:Normal Characters)123456789101112131415161718192021TRACKNo.Displayed Co

31、ntents2223242526272829303132333435363738394041TRACKNo.Displayed Contents1kHz/0dB/L&R20Hz/0dB/L&R40Hz/0dB/L&R100Hz/0dB/L&R200Hz/0dB/L&R500Hz/0dB/L&R1kHz/0dB/L&R5kHz/0dB/L&R7kHz/0dB/L&R10kHz/0dB/L&R16kHz/0dB/L&R18kHz/0dB/L&R20kHz/0dB/L&R1kHz/0dB/L&R1kHz/-1dB/L&R1kHz/-3dB/L&R1kHz/-6dB/L&R1kHz/-10dB/L&R

32、1kHz/-20dB/L&R1kHz/-60dB/L&R1kHz/-80dB/L&R1kHz/-90dB/L&RInfinity Zero w/o emphasis/L&RInfinity Zero with emphasis/L&R400Hz+7kHz(4:1)/0dB/L&R400Hz+7kHz(4:1)/-10dB/L&R19kHz+20kHz(1:1)/0dB/L&R19kHz+20kHz(1:1)/-10dB/L&R100Hz/0dB/L*1kHz/0dB/L*10kHz/0dB/L*20kHz/0dB/L*100Hz/0dB/R*1kHz/0dB/R*10kHz/0dB/R*20k

33、Hz/0dB/R*100Hz Squer Wave/L&R1kHz Squer Wave/L&R1kHz w/emphasis/-0.37dB/L&R5kHz w/emphasis/-4.53dB/L&R16kHz w/emphasis/-9.04dB/L&RNOTE : The contents of Track No. 1 to 41 are the same as those of the current TEST DISC-their titles are displayed.5CDP-CX355TRACKNo.Recorded contentsDisplayN All the sam

34、eN All the sameN All the sameN All the sameN All the sameN All the sameN All the sameX Y Z _ (58N All the sameN All the sameN All the samex y z I (78 i (A0 is not displayed(A8 C PRare not displayed (B023 are not displayed (B81 are not displayedN All the sameN All the sameN All the same Y (D8N All th

35、e sameN All the sameo (F0N All the sameN All the sameN All the sametoN All the same*4243444546474849505152535455565758596061626364656667to99! ” # $ %& (21h to 27h)1kHz 0dB L&R( )+ , . /(28h to 2Fh)0 1 2 3 4 5 6 7(30h to 37h)8 9 : ; ?(38h to 3Fh)A B C D E F G(40h to 47h)H I J K L MNO(48h to 4Fh)P QR

36、S T U VW(50h to 57h)X Y Z _(58h to 5Fh)a b c d e f g(60h to 57h)h i j k l m n o(68h to 6Fh)p q r s t u v w(70h to 77h)x y z I (78h to 7Fh)i (A0h to A7h) 8859-1C PR(A8h to AFh)23 (B0h to B7h)1(B8h to BFh) (C0h to C7h) (C8h to CFh)D (D0h to D7h) Y(D8h to DFh) (E0h to E7h) (E8h to FFh) (F0h to F7h) y(F

37、8h to FFh)No.66No.67 toNo.99141234141234Table 2: CD-TEXT TEST DISC Recorded Contents and Display(In this unit, some special characters cannot be displayed. This is no a fault.)6CDP-CX355SECTION 2GENERAL34 5 6 7 891011121215 16 17 18131423242526383919 20 21 2231 30 29 28 2736 35 34 33 32Location of P

38、arts and Controls11/u (power) button2STANDBY indicator3Display window4CONTINUE button5SHUFFLE button6PROGRAM button7REPEAT button8TIME/TEXT button9Front cover10 AMS /PUSH ENTER knob and button11 MENU/NO button12 +100 button13 YES button14 DISC/CHARACTER/PUSH ENTER knob and button15 EASY PLAY button

39、and indicator16 MEMO/SEARCH button17 CHECK button18 CLEAR button19 MEGA CONTROL button and indicator20 X-FADE button21 NO DELAY button22 FADER button23 p (stop)/DISC EJECT button24 P (pause) button and indicator25 (play) button and indicator26 OPEN/CLOSE button27 HIT LIST button and indicator28 GROU

40、P 4 button and indicator29 GROUP 3 button and indicator30 GROUP 2 button and indicator31 GROUP 1 button and indicator32 GROUP FILE button33 GROUP 8 button and indicator34 GROUP 7 button and indicator35 GROUP 6 button and indicator36 GROUP 5 button and indicator38 KEYBOARD jack39 TIMER OFF/PLAY switc

41、h* AMS is abbreviation for Automatic Music Sensor.7CDP-CX355SECTION 3DISASSEMBLYBRACKET (F.W.)(Page 8)SETDISP BOARD,JOG BOARD,KEYBOARD BOARD,(Page 9)FRONT PANEL ASSY(Page 9)CASE(Page 8)LED BOARD,GUIDE (DOOR.T)(Page 10)TABLE (300) ASSY,COVER (P.T.)(Page 10)D. MOTOR BOARD,DOOR MOTOR ASSY (M83)(Page 11

42、)BACK PANEL SECTION(Page 15)BRACKET (TOP),BU ASSY(Page 17)BD BOARDOPTICAL DEVICE(KSM-213BFM)(Page 18)MOTOR ASSY (LOADING) (M82),MOTOR ASSY (TABLE) (M81),L.T. MOTOR BOARD(Page 20)BU HOLDER ASSY(Page 17)MAIN BOARD,JACK BOARD(Page 16)L. SW (A) BOARD,L. SW (B) BOARD(Page 19)D. SW BOARD(Page 12)POP-UP AS

43、SY(Page 13)POWER BOARD(Page 16)BASE (DOOR.GEAR) ASSY(Page 13)CDM ASSY(Page 20)D. SENS (IN) BOARD(Page 15)D. SENS (OUT) BOARD(Page 14)T. SENS BOARD(Page 14) The parts surrounded by square are included in the solid line square in the area shown by the dotted line square .Note : Disassemble the unit in

44、 the order as shown below.8CDP-CX3553-1. Case1 two screws (CASE 3 TP2)3 two screws (CASE 3 TP2)4 two screws (CASE 3 TP2)5 case2 three screws (CASE 3 TP2)3-2. Bracket (F. W. )32 wire (flat type) (21 core) (CN501)1 connector (CN504)6 bracket (F.W.)5 two screws (+BVTP 3 x 8)4 screw (+BVTP 3 x 8)LED boa

45、rd9CDP-CX3553-3. Front Panel Assy7 two screws (+BVTP 3 x 8)6 three screws (+BVTP 3 x 8)5 cover (chassis)4 screw (+BVTP 3 x 8)3 connector (CN792)8 remove the claw9 remove the claw21q; front panel assy3-4. DISP Board, JOG Board, KEYBOARD Board7 remove two soldrings.3 four screws (+BVTP 2.6 x 8)5 two s

46、crews (+BVTP 2.6 x 8)6qd DISP board9 KEYBOARD board8 bracket (keyboard)4 bracket mainqh JOG boardqj front panel assyq; eight screws (+BVTP 2.6 x 8)qf five screws (B+VTP 2.6 x 8)qg seven screws (+BVTP 2.6 x 8)2 knob (AMS)qs knob (timer)1 knob (disc)qa wire (flat type) (21 core) (CN701)10CDP-CX3553-5.

47、 LED Board, Guide (Door. T)9 guide (door.T)3 screw (+BVTP 3 x 8)4571 screw (+BVTP 3 x 16)26 LED board8 window (internal illumination)Note during re-assemblingWhen re-assembling,align the positionsas shown.3-6. Table (300) Assy, Cover (P.T.)3 two screws (+BVTP 3x8)4 cover (front)6 door (CD) assy8 gui

48、de (door.B)57 three screws (+BVTP 3x8)q; cover (P.T.)9 two screws (+BVTP 3 x 8)1 table (300) assy2 two 10 washers11CDP-CX3553-7. D. MOTOR Board, Door Motor Assy (M83)1 remove two soldrings.2 D. motor board5 door motor assy (M83)4 belt3 two screws (+B 2.6 x 3)12CDP-CX3553-8. D. SW Board5 two screws (

49、+BTP 2.6 x 6)8 D. SW board7 holder (L-SW)6 two claws2 gear (door.cam)gear (door.cam)4 gear (door.drive)1 Move the slider (pop-up) and the lever (cam.pu) fully in the direction of the arrow A.3 When the gear (door.cam) happens to go too deep, return it to the original position in the direction of the

50、 arrow C.The levers of the two rotary switches on the D. SW boardare shown in the illustration below.slider (pop-up)lever (cam.pu)ABC1 washer3 washerPrecaution during the gear (door.cam) installationD. SW boardtwo rotary switches2 Install the gear (door.cam) in the direction shown in the illustratio