Yamaha-CDS300-cd-sm 维修电路原理图.pdf

《Yamaha-CDS300-cd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Yamaha-CDS300-cd-sm 维修电路原理图.pdf（57页珍藏版）》请在收音机爱好者资料库上搜索。

1、CD-S300Copyright 2009 All rights reserved.This manual is copyrighted by YAMAHA and may not be copied orredistributed either in print or electronically without permission.1 0 11 4 6SERVICE MANUALIMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service

2、 personnel.It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated.WARNING: Failure to follow appropriate service and safety procedures when servicing this

3、product may result in personal injury, destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representati

4、ve.IMPORTANT: The presentation or sale of this manual to any individual or fi rm does not constitute authorization, certifi cation or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.The data provided is believed to be accurate and applica

5、ble to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifi cations are subject to change without notice or obligation to retrofi t. Should any discre

6、pancy appear to exist, please contact the distributors Service Division.WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).IMP

7、ORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTSTO SERVICE PERSONNEL .23PREVENTION OF ELECTROSTATIC DISCHARGE .4FRONT PANEL .5REAR PANELS .56REMOTE CONTROL PANEL .7SPECIFICATIONS / 参考仕様 .8INTERNAL VIEW .9DISASSEMBLY PROC

8、EDURES / 分解手順 .1012TEST MODE / .1314FACTORY MODE / .15UPDATING FIRMWARE /書込 .1621DISPLAY DATA .22IC DATA .2330PIN CONNECTION DIAGRAMS .3132BLOCK DIAGRAM .33PRINTED CIRCUIT BOARDS .3440SCHEMATIC DIAGRAMS .4145REPLACEMENT PARTS LIST .4755REMOTE CONTROL .5609.09P.O.Box 1, Hamamatsu, JapanCOMPACT DISC P

9、LAYERCD-S300RadioFans.CN 收音机爱 好者资料库2CD-S300CD-S300“CAUTION”“F801: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 500mA, 250V FUSE.”CAUTIONF801: REPLACE WITH SAME TYPE 500mA, 250V FUSE.ATTENTIONF801: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 500mA, 250V.This product c

10、ontains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!Avoid prolonged, unprotected contact between solder and your skin! When soldering,

11、do not inhale solder fumes or expose eyes to solder/flux vapor!If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.1. Critical Components InformationComponents having special characteristics are marked and must be replac

12、ed with parts having specifications equal to those originally installed.2. Leakage Current Measurement (For 120V Models Only)When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equival

13、ent to 1500 ohms shunted by 0.15 F.本機搭載基板付接合部無鉛付。無鉛種類、修理時下記無鉛使用推奨。 Sn+Ag+Cu（錫 + 銀 + 銅） Sn+Cu（錫 + 銅） Sn+Zn+Bi（錫 + 亜鉛 + ）注意：無鉛融点温度通常鉛入比 30 40程度高、 合使用。All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder.Among some types of lead free solder currently avail

14、able, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth)Caution:As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead

15、 solder, be sure to use a soldering iron suitable to each solder. TO SERVICE PERSONNEL Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities.WALLOUTLETEQUIPMENTUNDER TESTAC LEAKAGETESTER OREQUIVALENTINSULATINGTABLEWARNING: CHEMICAL CONTENT NOTICE!Abou

16、t lead free solder / 無鉛WARNING: Laser SafetyThis product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during servicing of the un

17、it.1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm/1 feet away from the laser pick-up unit at all times. Do not stare at the laser beam at any time.2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewher

18、e in this manual.3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.RadioFans.CN 收音机爱 好者资料库3CD-S300CD-S300R, A, G, L, J modelsT modelLaser Emitting conditions:1) When the Top Cover is removed, and the STA

19、NDBY/ON SW is turned to the “ON” position, the laser component will emit a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the lens of the laser pick-up unit. Do not attempt any servicing during this period!If no disc is detected, t

20、he laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser emissions.2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory prior to shipping from the factory. Do not adjust this laser level cont

21、rol unless instruction is provided elsewhere in this manual. Adjustment of this control can increase the laser emission level from the device.Type: GaAlAsWavelength: 790 nmLaser output: max. 1.23 W * This output is the value measured at a distance of about 200 mm from the objective lens surface on t

22、he Optical Pick-up Block.Laser Diode PropertiesThe primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off !This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components whe

23、n servicing the player.Service personnel have to take precautions to prevent touching this area or components in this area.Note:The screws on the DVD mechanism may never be touched, removed or re-adjusted.Handle the DVD mechanism with care when the unit has to be exchanged!The DVD mechanism is very

24、sensitive for dropping or giving shocks.Warning for power supply4CD-S300CD-S300Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits an

25、d some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain o

26、ff any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES

27、devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not

28、classified as “anti-static (ESD protected)” can generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immedia

29、tely before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).7. Immediately before removing the protective material from the leads of a replacement ES device, touch the

30、 protective material to the chassis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless mot

31、ion such as brushing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).Grounding for electrostatic breakdown prevention1. Human body grounding.Use the antistatic wrist strap to discharge the static e

32、lectricity from your body.2. Work table grounding.Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.Caution:The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes tou

33、ch the optical pickup. PREVENTION OF ELECTROSTATIC DISCHARGE1M-ohmsConductive material(sheet) or steel sheetAnti-static wrist strap5CD-S300CD-S300 FRONT PANELR, T, A, G, L, J modelsR modelT model REAR PANELSA model6CD-S300CD-S300L modelG modelJ model7CD-S300CD-S300 REMOTE CONTROL PANELCDX88CD-S300CD

34、-S300 Audio Section / 部Output Level / 出力 (1 kHz, 0 dB) .2.0 0.3 VSignal to Noise Ratio / 信号対雑音比 . 105 dB or moreDynamic Range / . 96 dB or moreTotal Harmonic Distortion / 歪率 (1 kHz) .0.003 % or lessFrequency Response / 周波数特性 (2 Hz to 20 kHz) . 0.5 dBDigital Output Terminal / 出力端子 .Optical x 1Coaxial

35、 x 1Other Output Terminal / 他出力端子 .Analog out L/RUSB General / 総合Power Consumption / 消費電力 .13 WPower Supply / 電源電圧 R, L models . AC 110/120/220/230240 V, 50/60 HzT model .AC 220 V, 50 HzA model .AC 240 V, 50 HzG model .AC 230 V, 50 HzJ model .AC 100 V, 50/60 HzDimensions (W x H x D) / 寸法（幅高奥行） .435

36、x 86 x 260 mm (17-1/8 x 3-3/8 x 10-1/4)Weight / 質量 .3.5 kg (7.7 lbs.)Finish / 仕上 Black color .R, T, A, G, L, J modelsSilver color .R, T, A, G, L, J modelsAccessories / 付属品 Remote control (CDX8) .x 1Battery (R6, AA, UM-3) .x 2Audio pin cable (1.0 m) .x 1Power cable (1.5 m) .x 1* Specifications are su

37、bject to change without notice due to product improvements. 参考仕様外観予告変更。R .General modelT.Chinese modelA .Australian modelG .European modelL .Singapore modelJ .Japanese model SPECIFICATIONS / 参考仕様 DIMENSIONS / 寸法図395 (15-1/2)435 (17-1/8)70(2-3/4)210 (8-1/4)16(5/8)86(3-3/8)260 (10-1/4)“iPod” is a trad

38、emark of Apple Inc., registered in U.S. and other countries.“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards.Apple is not responsible for the operation of this device or it

39、s compliance with safety and regulatory standards.iPod 、米国他国登録 Apple Computer, Inc. 商標登録商標。Made for iPod、iPod 専用接続設計、定性能基準満認定電子示。、機器操作、安全規制基準関一切責任負。Unit: mm (inch)単位：mm（）9CD-S300CD-S300 INTERNAL VIEWOPERATION (7) P.C.B. (R, L models)OPERATION (5) P.C.B.OPERATION (9) P.C.B.MAIN P.C.B.OPERATION (4) P.

40、C.B.OPERATION (6) P.C.B.OPERATION (10) P.C.B.Loader mechanism assyOPERATION (8) P.C.B.OPERATION (2) P.C.B.OPERATION (3) P.C.B.OPERATION (1) P.C.B.12345678910111276981110122513410CD-S300CD-S300Fig. 1 DISASSEMBLY PROCEDURES / 分解手順(Remove parts in the order as numbered.)Disconnect the power cable from

41、the AC outlet.1. Removal of Top Covera. Remove 4 screws () and 2 screws (). (Fig. 1)b. Remove the top cover. (Fig. 1)（番号順部品取外。 ）AC 電源、電源抜。1. 外方a. 4 本、 2 本外。 （Fig. 1）b. 取外。 （Fig. 1）2. Removal of Front Panel Ass ya. Using a flatblade screwdriver, move the slider at the bottom in the direction of the a

42、rrow shown above.(Fig. 1)Open the disc tray, remove the lid and close the disc tray. (Fig. 1)b. Remove 2 screws (). (Fig. 1)2. ASSY 外方a. 底面上図矢印方向動。 （Fig. 1）開取外、閉。 （Fig. 1）b. 2 本外。 （Fig. 1）Top coverFront panel assyASSYLid HookHookCB803CB807CB6CB304OPERATION (6) P.C.B.OPERATION (8) P.C.B.MAIN P.C.B.Fl

43、atblade screwdriverLid Disc tray How to manually eject the disc tray / 開方法112345311CD-S300CD-S300Bottom view44455Fig. 23. Removal of Loader Mechanism Unita. Remove 4 screws (). (Fig. 3)b. Remove CB2 and CB3. (Fig. 3)c. Remove CB4 and ground the terminal side of the flexible flat cable with a clip or

44、 the like. (Fig. 3)d. Remove the loader mechanism unit. (Fig. 3)3. 外方a. 4 本外。 （Fig. 3）b. CB2、CB3 外。 （Fig. 3）c. CB4 外、電線端子面等。 （Fig. 3）d. 取外。 （Fig. 3）Fig. 3c. Remove 4 screws () and 2 screws (). (Fig. 2)d. Remove CB6, CB304, CB803 and CB807. (Fig. 1)e. Release 2 hooks and then remove the front panel a

45、ss y. (Fig. 1)c. 4 本、 1 本外。 （Fig. 2）d. CB6、CB304、CB803、CB807 外。 （Fig. 1）e. 2 箇所外、 ASSY 取外。 （Fig. 1）ClipTerminal side端子面17 mm(0.67)Use a clip or other item to ground the unit.等。Loader mechanism unit CB4CB3CB2MAIN P.C.B.6612CD-S300CD-S300Ground lead線ST701Ground lead線Rubber sheet and cloth布ChassisFront

46、 panel assyASSYFig. 4When checking the P.C.B.s: Spread the rubber sheet and the cloth. Then place this unit on the cloth and check it. (Fig. 4) Connect the ground point (ST701) of the front panel ass y to the chassis with a ground lead or the like. (Fig. 4) Reconnect all cables (connectors) that hav

47、e been disconnected. When connecting the flexible flat cable, be careful with polarity.P.C.B. 場合： 布敷、 上本機置。 （Fig. 4） ASSY （ST701）線等接続。 （Fig. 4） 外（）接続。 接続際、極性注意。13CD-S300CD-S300Power indicator電源 (Power) switch“ ” （電源） PURE DIRECT indicatorPURE DIRECT While pressing these keys, press the “ ” (Power) s

48、witch to turn on the power.押、 “ ” （電源） 押電源入。iPod/USB indicatoriPod/USB FL displayFL TEST MODE / FL display / FL 表示 起動起動時、FL表示状態。1. 本機下図示 “CD/USB” 、“” （頭出早送）、“” （）押 “ ” （電源）押電源入、3 押続。 Starting test modeWhen starting the test mode, check the FL display and indicators for display/indication condition.1

49、. While pressing the “CD/USB”, “” (Skip/Search forward) and “ ” (Pause) keys of this unit as shown in the figure below, press the “ ” (Power) switch to turn on the power and keep pressing those 3 keys.2. 3 押、全（電源、iPod/USB、PURE DIRECT）点灯確認。同時、FL 全点灯確認。3. 3 離。全（電源、iPod/USB、PURE DIRECT）、FL 全消灯確認。4. 起動。

50、2. While keep pressing those 3 keys, check that all indicators (Power, iPod/USB, PURE DIRECT) are lit.At the same time, check that all segments of the FL display are lit.3. Release those 3 keys.Then check that all indicators (Power, iPod/USB, PURE DIRECT) as well as all segments of the FL display ar