Loewe-Xemix_63510-dvd-sm 维修电路原理图.pdf

《Loewe-Xemix_63510-dvd-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Loewe-Xemix_63510-dvd-sm 维修电路原理图.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、CONTENTSSECTION 1 . . . . SUMMARYSECTION 2 . . . . CABINET & MAIN CHASSISSECTION 3 . . . . ELECTRICALSECTION 4 . . . . PARTS LISTRadioFans.CN 收音机爱 好者资料库SECTION 1SUMMARYCONTENTSPRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS. 1-3SERVICING PRECAUTIONS. 1-4 General Servicing Precautions Insulati

2、on Checking Prodedure Electrostatically Sensitive DevicesSPECIFICATIONS. 1-5RadioFans.CN 收音机爱 好者资料库1-3CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY,NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFAC-TURERS APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLYVOID THE WARRANTY, BUT MAY

3、LEAD TO YOUR BEING LIABLE FOR ANYRESULTING PROPERTY DAMAGE OR USER INJURY.SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARETHOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETYCHECKS AND SERVICING GUIDELINES. TO DO OTHERWISE,INCREASES THE RISK OF POTENTIAL HAZARDS AND INJURY TO THEUSER.WHILE SERVIC

4、ING, USE AN ISOLATION TRANSFORMER FOR PROTEC-TION FROM A.C. LINE SHOCK.SAFETY CHECKSAFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRCTED. ACHECK SHOULD BE MADE OF THE FOLLOWING.SUBJECT : FIRE & SHOCK HAZARD1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAYAS TO AVOID POSSIBILITY OF ADJACENT

5、 COMPONENT SHORTS.THIS IS ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARETRANSPORTED TO AND FROM THE REPAIR SHOP.2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICESSUCH AS INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER SUPPLY CORDS, AND OTHER HARDWARE HAVEBEEN REINSTALLED PER ORIGI

6、NAL DESIGN. BE SURE THAT THESAFETY PURPOSE OF THE POLARIZED LINE PLUG HAS NOT BEENDEFEATED.3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLDSOLDER JOINTS, SOLDER SPLASHES OR SHARP SOLDER POINTS.BE CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERI

7、ORATIONTO PARTS AND COMPONENTS. FOR FRAYED LEADS, DAMAGEDINSULATION (INCLUDING A.C. CORD). AND REPLACE IF NECESSARYFOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS.5. NO LEAD OR COMPONENT SHOULD TOUCH A RECIVING TUBE ORA RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUNDPROTRUNING METAL SURFACES MUS

8、T BE AVOIDED.6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOFRESISTORS, CAPACITORS, ETC. MUST BE REPLACED WITH EXACTFACTORY TYPES, DO NOT USE REPLACEMENT COMPONENTSOTHER THAN THOSE SPECIFIED OR MAKE UNRECOMMENDED CIR-CUIT MODIFICATIONS.7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN A.C.LEAKAG

9、E TEST ON ALL EXPOSED METALLIC PARTS OF THE CABI-NET, (THE CHANNEL SELECTOR KNOB, ANTENNA TERMINALS. HAN-DLE AND SCREWS) TO BE SURE THE SET IS SAFE TO OPERATEWITHOUT DANGER OF ELECTRICAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER DURING THIS TEST USE AN A.C. VOLT-METER, HAVING 5000 OHMS PER VOLT

10、 OR MORE SENSITIVITY, INTHE FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT RESIS-TOR, PARALLELED BY A .15 MFD. 150.V A.C TYPE CAPACITORBETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE, CON-DUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OH

11、M RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUGAND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED 75VOLTS R.M.S. THIS CORRESPONDS TO 0.5 MILLIAMP A.C ANYVALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCKHAZARD AND MUST BE CORRECTED IMM

12、EDIATELY.SUBJECT: GRAPHIC SYMBOLSTHE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHINAN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THESERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAG-NITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.THE EXCLAMATION POINT WIT

13、HIN AN EQUILATERAL TRIAN-GLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TOTHE PRESENCE OF IMPORTANT SAFETY INFORMATION INSERVICE LITERATURE.SUBJECT : X-RADIATION1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PER-SONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTEN-TIAL SOURCE OF X-RAYS IN

14、CURRENT T.V. RECEIVERS IS THE PIC-TURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHENTHE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERA-TION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PIC-TURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER

15、 CERTAIN CIR-CUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF DESIR-ABLE LEVELS.2. ONLY FACTORY SPECIFIED C.R.T. ANODE CONNECTORS MUST BEUSED. DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD INCOLOR SETS, ALWAYS RE-INSTALL THEM.3. IT IS ESSNTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE ANACCURATE AND RELIA

16、BLE HIGH VOLTAGE METER. THE CALIBRATION OF THE METER SHOULD BE CHECKED PERIODICALLYAGAINST A REFERENCE STANDARD, SUCH AS THE ONE AVAILABLEAT YOUR DISTRIBUTOR.4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLYTHERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERYTIME A COLOR CHASSIS IS SERVIC

17、ED. THE BRIGHTNESS SHOULDBE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGEWITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOESNOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGULATINGCORRECTLY, WE SUGGEST THAT YOU AND YOUR SERVICE ORGA-NIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGU-LATION I

18、S ALWAYS CHECKED AS A STANDARD SERVICING PROCE-DURE. AND THAT THE HIGH VOLTAGE READING BE RECORDER ONEACH CUSTOMERS INVOICE.5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS INA PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE,AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE ANDTHE HIGH VOLTAG

19、E SUPPLY. DO NOT OPERATE THE PRODUCTLONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS(WHERE USED).SUBJECT: IMPLOSION1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGR

20、AL IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BETAKEN TO AVOID DAMAGE DURING INSTALLATION, AVOIDSCRATCHING THE TUBE. IF SCRATCHED REPLACE IT.2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.SUBJECT : TIPS ON PROPER INSTALLATION1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBY-HOLE OR CLOS

21、ELY FITTING SHELF SPACE. OVER OR CLOSE TOHEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW.2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIOINSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIA-TORS WHERE STEAM LEAKAGE IS A FACTOR, ETC.3. AVOID PALCEMENT WHERE DRAPERIES MAY OBSTRUCT REARVENTING

22、. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DEC-ORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHTOBSTRUCT VENTILATION.4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMER-CIAL MOUNTING KIT. MUST FOLLOW THE FACTORY APPROVED MOUNTING INSTRUCTIONS A PRODUCT MOUNTED TO A SHELF ORPLATFORM MUST RETAIN ITS

23、ORIGINAL FEET (OR THE EQUIVALENTTHICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERSMUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGETEST ON CUSTOMIZED INSTALLATIONS.5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ONSLOPING SHELF OR A TILT

24、ED POSITION, UNLESS THE PRODUCT ISPROPERLY SECURED.6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITSMOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZ-ARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSSTHRESHOLDS OR DEEP PILE CARPETS.7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR S

25、TANDWHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.S OFTHE SAME OR LARGER SCREEN SIZE.8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING

26、 FROM A SIN-GLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TOHOME AND FAMILY.PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTSA.C. VOLTMETERGOOD EARTH GROUNDSUCH AS THE WATERPIPE. CONDUIT. ETCPLACE THIS PROBEON EACH EXPOSEDMETAL PART1-4SERVICING PRECAUTIONSCAUTION : Before servicing the DVD cov

27、ered by this servicedata and its supplements and addends, read and follow theSAFETY PRECAUTIONS. NOTE : if unforeseen circum-stances create conflict between the following servicing pre-cautions and any of the safety precautions in this publica-tions, always follow the safety precautions.Remembers Sa

28、fety First:General Servicing Precautions1. Always unplug the DVD AC power cord from the ACpower source before:(1)Removing or reinstalling any component, circuit board, module, or any other assembly.(2)Disconnection or reconnecting any internal electricalplug or other electrical connection.(3)Connect

29、ing a test substitute in parallel with an elec-trolytic capacitor.Caution : A wrong part substitution or incorrect polarity installation of electrolytic capacitors may resultin an explosion hazard.2. Do not spray chemicals on or near this DVD or any ofits assemblies.3. Unless specified otherwise in

30、this service data, cleanelectrical contacts by applying an appropriate contact cleaning solution to the contacts with a pipe cleaner,cotton-tipped swab, or comparable soft applicator.Unless specified otherwise in this service data, lubricationof contacts is not required.4. Do not defeat any plug/soc

31、ket B+ voltage interlocks withwhitch instruments covered by this service manual mightbe equipped.5. Do not apply AC power to this DVD and/or any of itselectrical assemblies unless all solid-state device heatsinks are cerrectly installed.6. Always connect test instrument ground lead to theappropriate

32、 ground before connection the test instrumentpositive lead. Always remove the test instrument ground lead last.Insulation Checking ProcedureDisconnect the attachment plug from the AC outlet and turnthe power on. Connect an insulation resistance meter(500V)to the blades of the attachment plug. The in

33、sulation resis-tance between each blade of the attachment plug and acces-sible conductive parts (Note 1) should be more than 1M-ohm.Note 1 : Accessible Conductive Parts including Metal pan-els, Input terminals, Earphone jacks, etc.Electrostatically Sensitive (ES) DevicesSome semiconductor (solid sta

34、te) devices can be damagedeasily by static electricity. Such components commonly arecalled Electrostatically Sensitive (ES) Devices. Examples oftypical ES devices are integrated circuits and some fieldeffect transistors and semiconductor chip components.The following techniques should be used to hel

35、p reduce theincidence of component damage caused by static electricity.1. Immediately before handling any semiconductor compo-nent or semiconductor-equipped assembly, drain off anyelectrostatic charge on your body by touching a knownearth ground. Alternatively, obtain and wear a commer-cially availa

36、ble discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge

37、buildup or exposure of the assembly.3. Use only a grouned-tip soldering iron to solder or unsolderES devices.4. Use only an anti-static solder removal device. Somesolder removal devices not classified a “anti-static” cangenerate electrical charges sufficient to damage ES devices.5. Do not use freon-

38、propelled chemicals. These cangenerate electrical charge sufficient to damage ESdevices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready toinstall it. (Most replacement ES devices are packaged withleads electrically shorted together by condu

39、ctive foam,aluminum foil, or comparable conductive material).7. Immediately before removing the protective material fromthe leads of a replacement ES device, touch the protectivematerial to the chassis or circuit assembly into which thedevice will be installed.Caution : Be sure no power is applied t

40、o the chassis orcircuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Normally harmless motion such as the brushing together of your clothes fabric or the liftingof your foot from a carpeted floor can generate static elec-trici

41、ty sufficient to damage an ES device.)1-5SPECIFICATIONS GENERALPower requirementsAC 110240V, 50/60HzPower consumption14WDimensions(approx.)360 x 69 x 215mm (W/h/d)Mass(approx.)2.52kgOperating temperature5C to 35C (41F to 95F)Operating humidity5% to 90% SYSTEMLaserSemiconductor laser, wavelength 650n

42、mSignal systemPAL/NTSCFrequency responseDVD (PCM 96kHz): 8Hz to 44kHzDVD (PCM 48kHz): 2Hz to 22kHzCD: 8Hz to 20kHzSignal-to-noise ratioMore than 100dB (ANALOG OUT connectors only)Harmonic distortionLess than 0.008%Dynamic rangeMore than 100dB(DVD)More than 95dB(CD) OUTPUTSVIDEO OUT1 V (p-p) 75 , syn

43、c negative, RCA jack x 1 /SCART (TO TV)Audio output (digital audio)0.5 V (p-p), 75 , RCA jack x 1Audio output (analog audio)2.0 Vrms (1 kHz, 0 dB), 600 ,RCA jack (L, R) x 1 / SCART (TO TV)3-353-364. FRONT CIRCUIT DIAGRAMSystem not operateRemocon not operatePower LED abnormalDigital abnormalSystem no

44、t operate orDihitron abnormal orKey not operate3-313-32System not working orDigitron not displayProgram download fail2.5 doesnt appearSystem not workingDigitron all not displaySystem not workingVideo signal notappearedNo Power onVideo signal YVideo signal ColorSystem not working orscreen is abnormal

45、2. SYSTEM CIRCUIT DIAGRAM3-293-30CIRCUIT DIAGRAMS1. POWER(SMPS) CIRCUIT DIAGRAMIMPORTANT SAFETY NOTICEWHEN SERVICING THIS CHASSIS, UNDER NO CIR-CUMSTANCES SHOULD THE ORIGINAL DESIGN BEMODIFIED OR ALTERED WITHOUT PERMISSIONFROM THE LOEWE CORPORATION. ALL COMPO-NENTS SHOULD BE REPLACED ONLY WITH TYPES

46、IDENTICAL TO THOSE IN THE ORIGINAL CIRCUIT.SPECIAL COMPONENTS ARE SHADED ON THESCHEMATIC FOR EASY IDENTIFICATION.THIS CIRCUIT DIAGRAM MAY OCCASIONALLY DIF-FER FROM THE ACTUAL CIRCUIT USED. THIS WAY,IMPLEMENTATION OF THE LATEST SAFETY ANDPERFORMANCE IMPROVEMENT CHANGES INTOTHE SET IS NOT DELAYED UNTI

47、LTHE NEW SERVICELITERATURE IS PRINTED.NOTE : 1. Shaded( ) parts are critical for safety. Replace only with specified part number.2. Voltages are DC-measured with a digital voltmeterduring Play mode.NOTES) WarningNOTES) Parts that are shaded are criticalNOTES) With respect to risk of fire orNOTES) el

48、ectricial shock.NOTES : Symbol denotes AC ground.Symbol denotes DC chassis ground.8V Power Dead.IC105 is defective.12V Power Dead.IC103 is defective.VF(-) Power Dead.ZD101 is defective.VF(+) Power Dead.F102 is defective.Power Dead.IC101 is defective.5V Power Dead.Q107 is defective.3.3V Power Dead.IC

49、106 is defective.3-333-343. RF & SERVO CIRCUIT DIAGRAMCD/DVD LDwill not on2-1SECTION 2CABINET & MAIN CHASSISCONTENTS1. EXPLODED VIEWS.2-21. Cabinet and Main Frame Section.2-22. Deck Mechanism Section.2-33. Packing Accessory Section.2-42-2EXPLODED VIEWS1. Cabinet and Main Frame Section467300A48452452

50、465465457275332OPTIONAL PART463463463463463A46250463260A43A00283A49A42280A54321BCD2-32. Deck Mechanism Section001003004431026021023025436436436022024A024B024A435022A032024027028031030434A02A03A01A00020011A010015015A015B015C017013014018011029012430431431012430433002A54321BCD3. Packing Accessory Secti