Aiwa-CX-JDS50-cs-sm维修电路原理图.pdf

《Aiwa-CX-JDS50-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Aiwa-CX-JDS50-cs-sm维修电路原理图.pdf（70页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALSony CorporationPersonal Audio GroupPublished by Sony Engineering CorporationAEP ModelCX-JDS20E ModelCX-JDS20/JDS50Australian ModelCX-JDS20Russian ModelCX-JDS20/JDS50COMPACT DISC DECK RECEIVER9-879-515-012005C1678-1 2005.03Ver. 1.0 2005.03SPECIFICATIONSCX-JDS20/JDS50CX-JDS20/JDS50 are

2、the Amplifier, CD player, TapeDeck and Tuner section in DBX-DS20/DBX-DS50. Continued on next page Model Name Using Similar MechanismNEWCDCD Mechanism TypeBU-F1BD81ASectionOptical Pick-up NameKSM-215DCP/C2NPTAPEModel Name Using Similar MechanismCX-LEM330SectionTape Transport Mechanism TypeJDS20CMAL5Z

3、220AJDS50CMAL1Z240APhoto : CX-JDS50Other models:JDS50The following measured at AC 120, 127, 220, 240 V 50/60 HzDIN power output (rated): 160 + 160 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):200 + 200 watts (6 ohms at 1 kHz, 10% THD)JDS20The following measured at AC 120, 127,

4、 220, 240 V 50/60 HzDIN power output (rated): 96 + 96 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):120 + 120 watts (6 ohms at 1 kHz, 10% THD)InputsAUDIO IN (stereo mini jack):voltage : impedance 47 kilohmsMIC (phone jack) (except for European model):seJDS20: 0.25 mVJDS50: 0.1

5、mV,nsitivity: impedance 10 kilohmsOutputsPHONES (stereo mini jack):accepts headphones of 8 ohms or moreSPEAKER:accepts impedance of 6 to 16 ohmsAmplifier sectionEuropean model:JDS20DIN power output (rated): 96 + 96 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):120 + 120 watts (

6、6 ohms at 1 kHz, 10% THD)Music power output (reference):180 + 180 watts (6 ohms at 1 kHz, 10% THD)Russian model:JDS50DIN power output (rated): 160 + 160 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):200 + 200 watts (6 ohms at 1 kHz, 10% THD)Music power output (reference):330 +

7、330 watts (6 ohms at 1 kHz, 10% THD)JDS20DIN power output (rated): 96 + 96 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):120 + 120 watts (6 ohms at 1 kHz, 10% THD)Music power output (reference):180 + 180 watts (6 ohms at 1 kHz, 10% THD)JDS20: 1.85 VJDS50: 0.9 V,RadioFans.CN 收音机

8、爱 好者资料库2CX-JDS20/JDS50SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PU

9、BLISHED BY SONY.GeneralPower requirementsEuropean and Russian models:230 V AC, 50/60 HzAustralian model:230 240 V AC, 50/60 HzArgentine model:220 V AC, 50/60 HzMexican model:127 V AC, 60 HzOther models:120 V, 220 V or 230 240 V AC, 50/60 HzAdjustable with voltage selectorPower consumptionEuropean mo

10、del:JDS20:198 watts0.25 watts (at the Power Saving Mode)Other models:JDS50:160 wattsJDS20:198 wattsDimensions (w/h/d) (excl. speakers):Approx. 230 365.5 409 mmMass (excl. speakers)Approx. 9.1 kgDesign and specifications are subject to change without notice.CD player sectionSystemCompact disc and dig

11、ital audio systemLaser Diode PropertiesEmission duration: continuousLaser Output: Less than 44.6 W(This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture)Frequency response2 Hz 20 kHz (0.5 dB)Signal-to-noise ratioM

12、ore than 90 dBDynamic rangeMore than 90 dBTape deck sectionRecording system4-track 2-channel, stereoFrequency response50 13,000 Hz (3 dB), using Sony TYPE I cassettesTuner sectionFM stereo, FM/AM superheterodyne tunerFM tuner sectionTuning range87.5 108.0 MHz(50 kHz step)AntennaFM lead antennaAntenn

13、a terminals75 ohms unbalancedIntermediate frequency10.7 MHzAM tuner sectionTuning rangeEuropean and Russian models:531 1,602 kHz (with the tuning interval set at 9 kHz)Other models:530 1,710 kHz (with the tuning interval set at 10 kHz)531 1,602 kHz (with the tuning interval set at 9 kHz)AntennaAM lo

14、op antennaAntenna terminalsExternal antenna terminalIntermediate frequency450 kHz Pan-American models:530 1,710 kHz (with the tuning interval set at 10 kHz)531 1,710 kHz (with the tuning interval set at 9 kHz) AbbreviationAUS: Australian modelE51: Chilean and Peruvian modelsMX: Mexican modelRU: Russ

15、ian modelModelPart No.JDS50: MX model2-595-343-0JDS20: MX model2-595-345-0JDS50: E51 model2-595-523-0JDS20: E51 model2-595-525-0JDS50: RU model2-599-602-0JDS20: AEP, RU models2-599-608-0JDS20: AUS model2-599-613-0MODEL IDENTIFICATION BACK PANEL 3#3Part No.RadioFans.CN 收音机爱 好者资料库3CX-JDS20/JDS50The la

16、ser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which

17、 is included in therepair parts.The flexible board is easily damaged and should be handled withcare.NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when ch

18、ecking the laser diode emission,observe from more than 30 cm away from the objective lens.NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNITNotes on chip component replacementNever reuse a disconnected chip component.Notice that the minus side of a tantalum capacitor may bedamaged by heat.Flexi

19、ble Circuit Board RepairingKeep the temperature of the soldering iron around 270 Cduring repairing.Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).Be careful not to apply force on the conductor when solderingor unsoldering.CAUTIONUse of controls or adjustme

20、nts or performance of proceduresother than those specified herein may result in hazardous radiationexposure.UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printe

21、d withthe lead free mark due to their particular size): LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a sligh

22、tly longer time.Soldering irons using a temperature regulator should be set toabout 350 C.Caution: The printed pattern (copper foil) may peel away ifthe heated tip is applied for too long, so be careful! Strong viscosityUnleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solde

23、r so use caution not to let solder bridgesoccur such as on IC pins, etc. Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.Laser component in this product is capable of emitting radiationexceeding the limit for Class 1.This appl

24、iance is classified as a CLASS 1 LASER product.The CLASS 1 LASER PRODUCT MARKING is located on theexterior.The release method of a CD disc tray LOCK functionThere is a disc lock function for the disc theft prevention for ademonstration at a shop front in this machine.Procedue:1.Press the ?/1 button

25、to turn the set on.2.Press two buttons of x and Z simultaneously for fiveseconds.3.The message “LOCKED” is displayed and the tray islocked. (Even if exiting from this mode, the tray is stilllocked.)4.Press two buttons of x and Z simultaneously for fiveseconds again.5.The message “UNLOCKED” is displa

26、yed and the tray isunlocked.6.To exit from this mode, press the ?/1 button to turn theset off.RadioFans.CN 收音机爱 好者资料库4CX-JDS20/JDS50TABLE OF CONTENTS1.GENERAL.52.DISASSEMBLY2-1.Disassembly Flow .72-2.Top Panel, Side Panel .82-3.Front Section .82-4.CD Mechanism Section.92-5.Cassette Mechanism Deck, D

27、S-PAI/HP/MIC Board .92-6.DS-PANEL Board . 102-7.Rear Cabinet . 102-8.Power Trans . 112-9.DS-MAIN Board, Heat Sink . 112-10. Holder (CD Mech). 122-11. Base Unit (BU-F1BD81A), CD Mech . 122-12. BD Board, Optical Pick-up (KSM-215DCP/C2NP) . 132-13. Frame. 132-14. Belt . 142-15. Cassette Panel. 153.TEST

28、 MODE. 164.MECHANICAL ADJUSTMENTS. 175.ELECTRICAL ADJUSTMENTS. 176.DIAGRAMS6-1.Block Diagram MAIN Section . 22 BD Section . 236-2.Printed Wiring Board BD Section . 246-3.Schematic Diagram BD Section . 256-4.Printed Wiring Board MAIN (JDS20) Section . 266-5.Printed Wiring Board MAIN (JDS50) Section .

29、 276-6.Schematic Diagram MAIN Section (1/2) . 286-7.Schematic Diagram MAIN Section (2/2) . 296-8.Printed Wiring Board PANEL (JDS20/JDS50) Section . 306-9.Schematic Diagram PANEL Section (1/2) . 316-10. Schematic Diagram PANEL Section (2/2) . 326-11. Printed Wiring Board PANEL COMB (JDS20) Section .

30、336-12. Printed Wiring Board PANEL COMB (JDS50) Section . 346-13. Schematic Diagram PANEL COMB Section . 356-14. Printed Wiring Board AMP (JDS20) Section . 366-15. Printed Wiring Board AMP (JDS50) Section . 376-16. Schematic Diagram AMP (JDS20) Section . 386-17. Schematic Diagram AMP (JDS50) Section

31、 . 396-18. Printed Wiring Board POWER (JDS20/JDS50) Section . 406-19. Schematic Diagram POWER Section . 417.EXPLODED VIEWS7-1.Overall Section . 507-2.Front Section . 517-3.Chassis Section. 527-4.CD Mechanism Section-1 . 537-5.CD Mechanism Section-2 . 548.ELECTRICAL PARTS LIST. 55RadioFans.CN 收音机爱 好者

32、资料库5CX-JDS20/JDS50SECTION 1GENERALThis section is extractedfrom instruction manual.Main unitAUDIO IN jack w; (28)BASS control qf (21)CANCEL wl (11)CD SYNC wk (18)Cassette compartment qh (17)DISC 1 3 4 (10)DISC SKIP/EX-CHANGE 5 (10, 13, 18)Disc tray 6 (9)DISPLAY qd (16, 25, 26)Display window 3 ENTER

33、wf (11, 13, 14)EQ 0 (20)FM MODE wd (16)FUNCTION wj (9, 13, 14, 15, 17, 18, 19, 21, 28)i-Bass 9 (20, 31)MIC jack1) qj (21)MIC LEVEL1) qk (21)MIDDLE control qs (21)Jog dial ws (11, 13)PHONES jack ql PLAY MODE wg (10, 13, 17)REC PAUSE/START 8 (18, 19, 21)Remote sensor 2REP wd (12)TREBLE control qa (21)

34、TUNER/BAND wh (14, 15)TUNING +/ wl (14, 15)TUNING MODE wg (14, 15)VOLUME control wa (27)?/1 (power) 1 (7, 15)Z (eject) 7 (9)Z PUSH (eject) qg (17)lm/ML (rewind/fast forward, go back/go forward) wl (10, 17)x (stop) wl (10, 17, 18, 21, 27, 31)N2) or nN3) (play) wl (10, 17, 18)X (pause) wl (10, 17, 31)

35、1)Except for European model2)DBX-DS203)DBX-DS50List of button locations and reference pagesHow to use this pageUse this page to find the location of buttons and other parts of the system that are mentioned in the text.Illustration numberrTUNER/BAND wh (14, 15)RRName of button/partReference pageALPHA

36、BETICAL ORDERA NM ZBUTTON DESCRIPTIONSqfw;qlqgqhqkqjwdwawswfwgwjwhwkwl1762 354890qaqsqdRadioFans.CN 收音机爱 好者资料库6CX-JDS20/JDS50Remote controlCD qk (9, 12)CLEAR qg (13)CLOCK/TIMER SELECT 2 (24, 25)CLOCK/TIMER SET 3 (8, 23, 24)DISC SKIP q; (10, 12)DISPLAY wa (16, 25, 26)ENTER 9 (8, 12, 14, 23, 24)EQ qf

37、(20)FM MODE 4 (16)FOLDER + qa (10, 12, 18)FOLDER qd (10, 12, 18)FUNCTION 6 (9, 12, 14, 15, 17, 28)PLAY MODE w; (10, 12, 17)REPEAT 4 (12)SLEEP ws (23)TAPE qj (17)TUNER BAND 5 (14, 15)TUNER MEMORY ql (14)TUNING MODE w; (14, 15)VOLUME +/ qs (23)?/1 (power) 1 (7, 24)m/M (rewind/fast forward) 7 (10, 17)N

38、 (play) 8 (10, 17)X (pause) 8 (10, 17)x (stop) 8 (10, 17)+/ (tuning) qh (14)./ (go back/go forward) qh (8, 10, 23)ALPHABETICAL ORDERA EF ZBUTTON DESCRIPTIONS456789q;ws1qdqgqfwaw;qlqkqjqhqaqs32Use buttons on the remote for the operation.1Press ?/1 to turn on the system.2Press CLOCK/TIMER SET.3Press .

39、 or repeatedly to set the hour.4Press ENTER.5Press . or repeatedly to set the minute.6Press ENTER.The clock starts working.To adjust the clock1Press CLOCK/TIMER SET.2Press . or repeatedly to select “CLOCK SET”, then press ENTER.3Do the same procedures as step 3 to 6 above.NotesThe clock settings are

40、 canceled when you disconnect the power cord or if a power failure occurs.You cannot set the clock in Power Saving Mode (page 25).Setting the clockRadioFans.CN 收音机爱 好者资料库7CX-JDS20/JDS50SECTION 2DISASSEMBLY2-1.DISASSEMBLY FLOWThis set can be disassembled in the order shown below.SET2-2. TOP PANEL, SI

41、DE PANEL(Page 8) 2-15. CASSETTE PANEL(Page 15) 2-3. FRONT SECTION(Page 8) 2-7. REAR CABINET(Page 10) 2-10. HOLDER (CD MECH)(Page 12) 2-14. BELT(Page 14) 2-8. POWER TRANS(Page 11) 2-11. BASE UNIT (BU-F1BD81A), CD MECH(Page 12) 2-4. CD MECHANISM SECTION(Page 9) 2-6. DS-PANEL BOARD(Page 10) 2-5. CASSET

42、TE MECHANISM DECK, DS-PAI/HP/MIC BOARD(Page 9) 2-9. DS-MAIN BOARD, HEAT SINK (Page 11) 2-13. FRAME(Page 13) 2-12. BD BORD, OPTICAL PICK-UP(KSM-215DCP/C2NP)(Page 13) RadioFans.CN 收音机爱 好者资料库8CX-JDS20/JDS50Note: Follow the disassembly procedure in the numerical order given.2-2.TOP PANEL, SIDE PANEL2-3.

43、FRONT SECTIONqatop panel2two screws(+BVTP 3 10) 5two screws(+BVTP 3 10)7three screws(+BVTP 3 10)3right panel6left panel1four screws(Case 3)4four screws(Case 3)q;989front section5three screws(+BVTP)(B3)6screw(+BVTP)(B3)8screw(+BVTP)(B3)7screw(+KTP 3 6)1 wire (flat type) (11core) (CN112)2 wire (flat t

44、ype) (15core) (CN604) 4 wire (flat type) (27core) (CN604)3 connector (6p) (cassette deck)RadioFans.CN 收音机爱 好者资料库9CX-JDS20/JDS502-4.CD MECHANISM SECTION2-5.CASSETTE MECHANISM DECK, DS-PAI/HP/MIC BOARD1two screws(+BVTP)(B3) 2CD mechanism section2 wire (flat type) (8core)1three screws(+PTP)(B2.6)3three

45、 screws(+PTP)(B2.6)5two screws(+PTP)(B2.6)6holder (PWB MIC)7DS-PAI/HP/MIC board4cassette mechanism deck RadioFans.CN 收音机爱 好者资料库10CX-JDS20/JDS502-6.DS-PANEL BOARD2-7.REAR CABINET1 knob (RTRY)3 knob (RTRY AMS)2 guide (LED VOL)4twenty screws (+PTP)(B2.6)6DS-PANEL board3 connector (11p) (CN651)2 wire (f

46、lat type) (11core)1 connector (2p) (CN871)3four screws(+BVTP)(B3) 4rear cabinetRadioFans.CN 收音机爱 好者资料库11CX-JDS20/JDS502-8.POWER TRANS2-9.DS-MAIN BOARD, HEAT SINK1four screws3power trans2cord bushing 5DS-MAIN board4connector6heat sink1two screws(+BVTP)(B3) 3screw(+BVTP)(B3)2two screws(+BVTP)(B3)Radio

47、Fans.CN 收音机爱 好者资料库12CX-JDS20/JDS502-10. HOLDER (CD MECH)2-11. BASE UNIT (BU-F1BD81A), CD MECH2wire (flat type) (27 core) (CN606)4wire (flat type) (27 core)3tape5screw (+BVTP 2.6 8)6DS CONN board7holder (CD MECH)1four screws (+BVTP 2.6 8) 2two coil springs (insulator)4two coil springs (insulator)1two

48、 floating screws (+PTPWH M2.6)3two floating screws (+PTPWH M2.6)6base unit (BU-F1BD81A)7tray panel8CD mech5wire (flat type) (27 core)RadioFans.CN 收音机爱 好者资料库13CX-JDS20/JDS502-12. BD BOARD, OPTICAL PICK-UP (KSM-215DCP/C2NP)6two insulators 7two insulators 2gap tube5BD board8optical pick-up (KSM-215DCP/

49、C2NP)1screw (+BVTP 2.6 8) 4Remove the four solderings of motor.3wire (flat type) (16 core)2-13. FRAME1four screws2frame RadioFans.CN 收音机爱 好者资料库14CX-JDS20/JDS502-14. BELT2 Slide the upper-most tray foward the front.1 Release the hook of the tray.3 While pushing up the plate cam, draw the Drawer (thre

50、e trays) entirely foward front.4 two beltsplate camRadioFans.CN 收音机爱 好者资料库15CX-JDS20/JDS502-15. CASSETTE PANEL4cassette panel3two claws2Open the cassette panel.1Push the cassette panel.RadioFans.CN 收音机爱 好者资料库16CX-JDS20/JDS50SECTION 3TEST MODECOLD RESET*The cold reset clears all data including preset