Aiwa-CXJN331-cs-sm维修电路原理图.pdf

《Aiwa-CXJN331-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Aiwa-CXJN331-cs-sm维修电路原理图.pdf（80页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOMPACT DISC DECK RECEIVERE ModelSPECIFICATIONSCX-JN331/JPK331Ver. 1.0 2005.05Model Name Using Similar MechanismCX-JN33/JPK33CDCD Mechanism TypeCDM74KS-F1BD81CSectionBase Unit NameBU-F1BD81COptical Pick-up NameKSM-215DCPTape deckModel Name Using Similar MechanismCX-JN33/JPK33Tape Trans

2、port Mechanism TypeCWM43FF13 (JPK331)SectionCWM43FR34 (JN331)9-879-731-012005E05-1 2005.05Sony CorporationPersonal Audio GroupPublished by Sony Engineering Corporation Continued on next page CX-JN331 is the amplifier, CD player, tape deckand tuner section in JAX-N331.CX-JPK331 is the amplifier, CD p

3、layer, tape deckand tuner section in JAX-PK331.CX-JN331The following measured at AC 120, 127, 220, 240 V 50/60 HzDIN power output (rated): 48 + 48 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):60 + 60 watts (6 ohms at 1 kHz, 10% THD)CX-JPK331The following measured at AC 120, 12

4、7, 220, 240 V 50/60 HzDIN power output (rated): 48 + 48 watts (6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):60 + 60 watts (6 ohms at 1 kHz, 10% THD)InputsVIDEO/MD IN (phono jacks):voltage 450/250 mV, impedance 47 kilohmsMIC (phone jack) chilean and peruvian model sensitivity 1 mV,imp

5、edance 10 kilohmsAmplifier sectionOutputsPHONES (stereo mini jack):accepts headphones of 8 ohms or moreSPEAKER:accepts impedance of 6 to 16 ohmsCD player sectionSystemCompact disc and digital audio systemLaser Diode PropertiesEmission duration: continuousLaser Output: Less than 44.6 W(This output is

6、 the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture)Frequency response2 Hz 20 kHz (0.5 dB)Signal-to-noise ratioMore than 90 dBDynamic rangeMore than 90 dBTape deck sectionRecording system4-track 2-channel, stereoFrequency res

7、ponse50 13,000 Hz (3 dB), using Sony TYPE I cassettesWow and flutter0.15% W. Peak (IEC) 0.1% W. RMS (NAB) 0.2% W. Peak (DIN)AM tuner sectionTuning range2 Band type:Tuner sectionFM stereo, FM/AM superheterodyne tunerFM tuner sectionTuning range87.5 108.0 MHz(50-kHz step)AntennaFM lead antennaAntenna

8、terminals75 ohms unbalancedIntermediate frequency10.7 MHz530 1,710 kHz (with the tuning interval set at 10 kHz)531 1,602 kHz (with the tuning interval set at 9 kHz)AntennaAM loop antennaAntenna terminalsExternal antenna terminalIntermediate frequency450 kHz RadioFans.CN 收音机爱 好者资料库2CX-JN331/JPK331Gen

9、eralPower requirementsMexican models:127 V AC, 60 HzOther models:120 V, 220 V or 230 240 V AC, 50/60 HzAdjustable with voltage selector110 wattsDimensions (w/h/d) incl. projecting parts and controls Amplifier/Tuner/Tape/CD section:Approx. 280 325 425 mmPower consumptionMass Approx. 8.3 kgDesign and

10、specifications are subject to change without notice.Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may bedamaged by heat.Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 Cduring r

11、epairing. Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times). Be careful not to apply force on the conductor when solderingor unsoldering.This appliance is classified as a CLASS 1LASER product.This label is located on the rear exterior.CAUTIONUse of controls o

12、r adjustments or performance of proceduresother than those specified herein may result in hazardous radiationexposure.SAFETY-RELATED COMPONENT WARNING!COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE

13、 COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.RadioFans.CN 收音机爱 好者资料库3CX-JN331/JPK331TABLE OF CONTENTS1.SERVICING NOTES.42.GENERAL.73.DISASSEMBLY3-1.Disassembly Flow .93-2.Case (Side-L/R) . 103-3.Case (Top) . 103-4.Tray Panel. 113-5.C

14、D Mechanism Deck (CDM74KS-F1BD81C). 113-6.Front Pack Block . 123-7.Back Panel Section . 123-8.MAIN Board. 133-9.Tape Mechanism Deck(CWM43FF13: JPK331)/(CWM43FR34: JN331) . 133-10. Table Assy . 143-11 MOTOR (TB) Board . 143-12 MOTOR (LD) Board . 153-13 Base Unit (BU-F1BD81C) . 153-14 Motor Gear Assy

15、(Sled) (M102), CD BOARD . 163-15 Optical Pick-up (KSM-215DCP) . 164.TEST MODE. 175.MECHANICAL ADJUSTMENTS. 216.ELECTRICAL ADJUSTMENTS. 217.DIAGRAMS7-1.Block Diagram SERVO Section . 247-2.Block Diagram MAIN Section . 257-3.Block Diagram PANEL/POWER SUPPLY Section . 267-4.Printed Wiring Board CD Board

16、 . 287-5.Schematic Diagram CD Board . 297-6.Printed Wiring Boards CHANGER Section . 307-7.Schematic Diagram CHANGER Section . 317-8.Printed Wiring Board CDMP3 CONNECT Board . 327-9.Schematic Diagram CDMP3 CONNECT Board . 337-10. Schematic Diagram MAIN Section (1/4) . 347-11. Schematic Diagram MAIN S

17、ection (2/4) . 357-12. Schematic Diagram MAIN Section (3/4) . 367-13. Schematic Diagram MAIN Section (4/4) . 377-14. Printed Wiring Boards MAIN Section . 387-15. Printed Wiring Boards PANEL Section . 397-16. Schematic Diagram PANEL Section (1/2) . 407-17. Schematic Diagram PANEL Section (2/2) . 417-

18、18. Printed Wiring Board POWER AMP Section . 427-19. Schematic Diagram POWER AMP Section . 437-20. Printed Wiring Boards TRANS Section . 447-21. Schematic Diagram TRANS Section . 458.EXPLODED VIEWS8-1.Case Section . 568-2.Tape Mechanism Deck Section(CWM43FF13: JPK331)/(CWM43FR34: JN331). 578-3.Panel

19、 Board Section . 588-4.Cassette Box Section . 598-5.Front Panel Section . 608-6.Back Panel Section . 618-7.Chassis Section. 628-8.CD Mechanism deck Section-1(CDM74KS-F1BD81C) . 638-9.CD Mechanism deck Section-2(CDM74KS-F1BD81C) . 648-10. CD Mechanism deck Section-3(CDM74KS-F1BD81C) . 658-11. Base Un

20、it (BU-F1BD81C) . 669.ELECTRICAL PARTS LIST. 67RadioFans.CN 收音机爱 好者资料库4CX-JN331/JPK331The laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay

21、 attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe di

22、sc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.LASER DIODE AND FOCUS SEARCH OPERATIONCHECKCarry out the “S curve check” in “CD section adjustment” and checkthat the

23、S curve waveforms is output three times.SECTION 1SERVICING NOTESNOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNITUNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not

24、come printed withthe lead free mark due to their particular size): LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint

25、for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 C.Caution: The printed pattern (copper foil) may peel away ifthe heated tip is applied for too long, so be careful! Strong viscosityUnleaded solder is more viscou-s (sticky, less prone to flow)than ord

26、inary solder so use caution not to let solder bridgesoccur such as on IC pins, etc. Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.MODELPART No.CX-JPK331: Mexican model4-252-231-2CX-JN331/JPK331: Chilean and Peruvian models4-

27、252-231-3 MODEL IDENTIFICATION+RLRL Rear View PART No.RadioFans.CN 收音机爱 好者资料库5CX-JN331/JPK331HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF.SERVICE POSITION CD MECHANISM DECK CD mechanism deckstandCDMP3 CONNECT board1Remove the case (side-L).2Turn the loading gear in the direction of arrow A.

28、A3Pull-out the disc tray.RadioFans.CN 收音机爱 好者资料库6CX-JN331/JPK331 FRONT PANEL SECTION AMP BOARD MAIN boardPANEL boardfront panel sectiontape mechanism deckSUB TRANS boardTRANS boardAMP boardMAIN boardfront panel sectionRadioFans.CN 收音机爱 好者资料库7CX-JN331/JPK331SECTION 2GENERALThis section is extracted f

29、rominstruction manual. LOCATION OF CONTROLSMain unitALBUM + wkALBUM wkBASS control 5CD qhCD SYNC qsDeck A 9Deck B wlDISC 1 3 wdDISC SKIP/EX-CHANGE wfOperation Dial (AMS/TUNING) qf?/1 (power) 1ALPHABETICAL ORDERA NO ZBUTTON DESCRIPTIONS+ZZwdwfwgwhwk4qjqhqk qlw;wawswj1qgqfqdqs0qa928356 7wle;Disc tray

30、wsDISPLAY qgDisplay window 4ENTER 2i-Bass qdMIC jack2)e;MIC LEVEL2)e;MIDDLE control 5P FILE 6PHONES jack qaPLAY MODE w; PRESET EQ 3REC PAUSE/START 8Remote sensor 7SURROUND waTAPE A/B qkTREBLE control 5TUNER/BAND qjTUNING MODE w;VIDEO/MD qlVOLUME control whZ PUSH (deck A) (eject) 0Z (eject) wgPUSH Z

31、(deck B) (eject) wjm (rewind) wkx (stop) wkH or hH1) (play) wk X (pause) wkM (fast forward) wk1)CX-JN331 only2)CX-JPK331 chilean and peruvian model onlyRadioFans.CN 收音机爱 好者资料库8CX-JN331/JPK331Remote controlALBUM + qaALBUM qdCD qkCLEAR qgCLOCK/TIMER SELECT 2FM MODE 4FUNCTION 6PLAY MODE w;REPEAT 4SLEEP

32、 wsTAPE qjTUNER BAND 5TUNER MEMORY qlTUNING MODE w;VOLUME +/ qs?/1 (power) 1m/M (rewind/fast forward) 7N (play) 8X (pause) 8x (stop) 8/+ (tuning) qh./ (go back/go forward) qhALPHABETICAL ORDERA EF ZBUTTON DESCRIPTIONS456789q;ws1qdqgqfwaw;qlqkqjqhqaqs32CLOCK/TIMER SET 3DISC SKIP 0DISPLAY waENTER 9EQ

33、qfRadioFans.CN 收音机爱 好者资料库CX-JN331/JPK3319 This set can be disassembled in the order shown below.3-1.DISASSEMBLY FLOWSECTION 3DISASSEMBLYSET3-2.CASE(SIDE-L/R)(Page 10)3-3.CASE (TOP)(Page 10)3-4.TRAY PANEL(Page 11)3-6.FRONT PANELBLOCK(Page 12)3-7.BACK PANELSECTION(Page 12)3-9.TAPE MECHANISMDECK(CWM43F

34、F13: JPK331)/(CWM43FR34: JN331)(Page 13)3-8.MAIN BOARD(Page 13)3-14. MOTOR GEAR ASSY (SLED) (M102),CD BOARD(Page 16)3-15. OPTICAL PICK-UP(KSM-215DCP)(Page 16)3-13. BASE UNIT(BU-F1BD81C)(Page 15)3-10. TABLE ASSY(Page 14)3-11. MOTOR (TB)BOARD(Page 14)3-12. MOTOR (LD)BOARD(Page 15)3-5.CD MECHANISM DECK

35、(CDM74KS-F1BD81C)(Page 11)Note 1:The process described in can be performed in any order.Note 2:Without completing the process described in , the next process can not be performed.RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331103-3.CASE (TOP)Note: Follow the disassembly procedure in the numerical order given

36、.3-2.CASE (SIDE-L/R)3case (top)2three claws1two screws(BVTP3 10)4case (side-L)7case (side-R)6two screws(BVTP3 10)3two screws(BVTP3 10)1two screws (case 3 TP2)5three screws (case 3 TP2)2screw (case 3 TP2)RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331113-4.TRAY PANEL3-5.CD MECHANISM DECK(CDM74KS-F1BD81C)1Turn

37、 the loading gearin the direction of arrow A.Afour claws3Remove the tray panelin the direction of arrow C.C2Pull-out the tray in the direction of arrow B.B7CD mechanism deck(CDM74KS-F1BD81C)2screw(BVTP3 10)3three screws(BVTP3 10)1screw(BVTP3 10)5wire (flat type) (17 core)(CN873)6two connectors(CN701

38、, CN874)4RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331123-7.BACK PANEL SECTION3-6.FRONT PANEL BLOCK3screw(BVTP3 8)4harness6front panel block5three screws(BVTP3 8)2connector(CN112)2connector(CN324)1wire (flat type) (29 core)(CN302)2connector(CN309)2connector(CN103)3two screws(BVTP3 10)1wire (flat type) (15

39、core) (CN101)2two connectors(CN904, 906)2connector (CN901)4duct cover9back panel section5three screws(BVTP3 10)6two screws(BVTP3 8)8SUB TRANS board7two screws(BVTP3 10)RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331133-8.MAIN BOARD3-9.TAPE MECHANISM DECK(CWM43FF13: JPK331)/(CWM43FR34: JN331)3connector(CN307)

40、2two screws(BVTP3 8)1connector(CN907)4MAIN board1six screws(BVTP2.6 8)2tape mechanism deck(CWM43FF13: JPK331)/(CWM43FR34: JN331)RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331143-10. TABLE ASSY3-11. MOTOR (TB) BOARD3wire (flat type) (5 core)(CN702)4hook1Turn the loading gearin the direction of arrow A.A5two

41、claws2Pull-out the table assy.6table assy2tray4connector(CN731)1screw(PTPWH M2.6)5two screws(BTTP M2.6)6MOTOR (TB) board3belt (table)RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331153-12. MOTOR (LD) BOARD3-13. BASE UNIT (BU-F1BD81C)2connector(CN704)3two screws(BTTP M2.6)4MOTOR (LD) board1belt (loading)3four

42、coil springs(insulator)1wire (flat type) (27 core) (CN201)2four floating screws(PTPWHM2.6)4four insulators5base unit (BU-F1BD81C)RadioFans.CN 收音机爱 好者资料库CX-JN331/JPK331163-14. MOTOR GEAR ASSY (SLED) (M102), CD BOARD3-15. OPTICAL PICK-UP (KSM-215DCP)1Remove twosolders.qaCD board2two screws(P2 3)6claw7

43、gear (A)8gear (B)5wire (flat type) (16 core)(CN101)0motor gear assy (SLED)(M102)3screw (2.6 8)9Remove two solders.42sled shaft1Slide the leverin the direction of arrow A.3Remove the optical pick-up(KSM-215DCP) in the directionof arrow B.ABRadioFans.CN 收音机爱 好者资料库17CX-JN331/JPK331SECTION 4TEST MODEMC

44、COLD RESET The cold reset clears all data including preset data stored inthe RAM to initial conditions. Execute this mode whenreturning the set to the customer.Procedure:1. Press theI/1button to turn the power ON.2. Press three buttons of x , P FILE and DISC 1 simultaneously.3. The message “COLD RES

45、ET” is displayed on the fluorescentindicator tube momentarily, then becomes standby states.TUNER STEP CHANGE-OVER A step of AM channels can be changed over between 9 kHzand 10 kHz.Procedure:1. Press theI/1button to turn the power ON.2. Press the TUNER/BAND button to select “AM”.3. Press theI/1button

46、 to turn the power OFF.4. Press two buttons of PLAY MODE/TUNING MODE andI/1simultaneously.5. The message “AM 9K STEP” or “AM 10K STEP” is displayedon the fluorescent indicator tube, and thus the channel step ischanged over.CD SHIP (LOCK) MODE This mode moves the optical pick-up to the position durab

47、leto vibration. Use this mode when returning the set to thecustomer after repair.Procedure:1. Press theI/1button to turn the power ON.2. Press the CD button to select “CD”.3. Press two buttons of CD and POWER simultaneously.4. The message “LOCK” is displayed on the fluorescent indicatortube, and the

48、 CD ship mode is set.CD SHIP (LOCK) MODE & COLD RESET This mode is used to perform CD chip (lock) mode and coldreset simultaneously.Procedure:1. Press theI/1button to turn the power ON.2. Press the CD button to select “CD”.3. Press three buttons ofx , CD and DISPLAY simultaneously.4. The message “CO

49、LD RESET” is displayed on the fluorescentindicator tube momentarily, then becomes standby states.CHANGE-OVER FUNCTION OF MD/VIDEO This mode is used to enable function of external input to changeover between MD and VIDEO.Procedure:1. Press theI/1button to turn the power ON.2. Press two buttons ofVIDE

50、O (MD)andI/1simultaneously.3. The message “MD” or “VIDEO”is displayed on the fluorescentindicator tube, and the function of external input is changedover.CD TRAY LOCK MODE This mode is used to unable to take sample disc out of tray inthe shop.Procedure:1. Press theI/1button to turn the power ON.2. P