Aiwa-NSXWV89-cs-sm维修电路原理图.pdf

《Aiwa-NSXWV89-cs-sm维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《Aiwa-NSXWV89-cs-sm维修电路原理图.pdf（46页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALDATACOMPACT DISC STEREOCASSETTE RECEIVERBASIC TAPE MECHANISM : 2ZM-3MK2 PR7NMBASIC CD MECHANISM : AZG-1 VZD3RNDMNSX-WV89HRS/M Code No. 09-006-433-5R1REVISION This Service Manual is the Revision Publishing and replaces Simple ManualNSX-WV89 (HR), (S/M Code No. 09-004-433-5T1). If requir

2、ing information about the CD mechanism, see Service Manual of AZG-1 VZD3RNDM, (S/M Code No. 09-001-335-3NG).NSXWV89MAINSPEAKERSYSTEMCDCASSEIVERREMOTECONTROLLERRCZAS08CXNWV89SXNDP84RadioFans.CN 收音机爱 好者资料库 2 Tuning range87.5 MHz to 108 MHzUsable sensitivity (IHF)13.2 dBfAntenna terminals75 ohms (unbal

3、anced)Tuning range531 kHz to 1602 kHz (9 kHz step)530 kHz to 1710kHz (10 kHz step)Usable sensitivity350 V/mAntennaLoop antennaTuning range5.730 MHz to 17.900 MHzAntennaWire antennaPower outputFrontRated: 115 W + 115 W (6 ohms, T.H.D.1 %, 1 kHz/DIN 45500)Reference: 145 W + 145 W (6 ohms,T.H.D. 10 %,

4、1 kHz/DIN 45324)Rear (Surround)Rated: 25 W + 25 W (8 ohms, T.H.D.1 %, 1 kHz/DIN 45500)Reference: 35 W + 35 W (8 ohms,T.H.D. 10 %, 1 kHz/DIN 45324)CenterRated: 30 W (8 ohms, T.H.D.1 %, 1 kHz/DIN 45500)Reference: 40 W (8 ohms,T.H.D. 10 %, 1 kHz/DIN 45324)Total harmonic distortion0.1 % (10.5 W, 1 kHz,

5、6 ohms,DIN AUDIO/Front )InputsVIDEO/AUX: 316 mV (adjustable)MD: 316 mV (adjustable)MIC 1, MIC 2:1.0 mV (10 kohms)5.1 CH INPUT (adjustable) FRONT (L,R): 330 mV REAR (L,R): 200 mV CENTER: 510 mV SUB WOOFER: 360 mVOutputsFRONT SPEAKERS:accept speakers of 6 ohms or moreSURROUND SPEAKERS:accept speakers

6、of 8 ohms to 16 ohmsor moreCENTER SPEAKER:accept speakers of 8 ohms or moreSUBWOOFER: 1.1 VVIDEO OUT: 1.0 Vp-p (75 ohms)LINE OUT: 210 mVPHONES (stereo jack): acceptsheadphones of 32 ohms or moreSPECIFICATIONSTrack format4 tracks, 2 channels stereoFrequency responseCrO2 tape: 50 Hz 16000 HzNormal tap

7、e: 50 Hz 15000 HzRecording systemAC biasHeadsDeck 1: Playback head x 1Deck 2: Recording/Playback head x 1,erase head x 1LaserSemiconductor laser ( =780 nm)D-A converter1 bit dualSignal-to-noise ratio85 dB (1 kHz, 0 dB)Harmonic distortion0.05 % (1 kHz, 0 dB)Wow and flutterUnmeasurableVideo signalNTSC

8、/PAL color format (selectable)Video dataMPEG 1Audio dataMPEG 1, LAYER 2Power requirements120 V/220230 V/240 V AC(switchable), 50/60 HzPower consumption245 WPower consumption inIf the power-economizing mode isstandby modeECO OFF: 31 WIf the power-economizing mode isECO ON or ECO AUTO: 0.9 WDimensions

9、 of main unit260 x 329 x 389.6 mm(W x H x D)Weight of main unit12.2 kgSpeaker system2 way, bass reflex (magneticshielded type)Speaker unitsWoofer:160 mm cone typeTweeter:60 mm cone typeImpedance6 ohmsSensitivity87 dB/W/mDimensions (W x H x D)240 x 324 x 245 mmWeight5.0 Kg Design and specifications a

10、re subject to change without notice. Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY”, the double-D symbol and PRO LOGIC are trademarks of Dolby Laboratories Licensing Corporation. The word BBEand the BBE symbol are trademarks of BBE Sound, Inc. Under license from BB

11、E Sound,Inc.RadioFans.CN 收音机爱 好者资料库 3 CLASS 1LASER PRODUCTKLASSE 1LASER PRODUKTLUOKAN 1LASER LAITEKLASS 1LASER APPARATThis set employs laser. Therefore, be sure to follow carefullythe instructions below when servicing.WARNING!WHEN SERVICING, DO NOT APPROACH THE LASEREXIT WITH THE EYE TOO CLOSELY. IN

12、 CASE IT ISNECESSARY TO CONFIRM LASER BEAM EMISSION.BE SURE TO OBSERVE FROM A DISTANCE OF MORETHAN 30cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL PICK-UP BLOCK.sCaution: Invisible laser radiation whenopen and interlocks defeated avoidexposure to beam.sAdvarsel: Usynlig laserstling ved b

13、ning,nr sikkerhedsafbrydere er ude af funktion.Undg udsttelse for strling.VAROITUS!Laiteen Kyttminen muulla kuin tss kyttohjeessamainitulla tavalla saataa altistaa kyt-tjnturvallisuusluokan 1 ylittvlle nkymttmllelasersteilylle.VARNING!Om apparaten anvnds p annat stt n vad somspecificeras i denna bru

14、ksanvising, kan anvndarenutsttas fr osynling laserstrlning, som verskridergrnsen fr laserklass 1.PROTECTION OF EYES FROM LASER BEAM DURING SERVICINGCAUTIONUse of controls or adjustments or performance of proce-dures other than those specified herin may result inhazardous radiation exposure.ATTENTION

15、Lutillisation de commandes, rglages ou procduresautres que ceux spcifis peut entraner une dangereuseexposition aux radiations.ADVARSELUsynlig laserstling ved bning, nr sikkerhedsafbrydereerude af funktion. Undg udsttelse for strling.This Compact Disc player is classified as a CLASS 1LASER product.Th

16、e CLASS 1 LASER PRODUCT label is located on therear exterior.Precaution to replace Optical block(KSS-213F)Body or clothes electrostatic potential couldruin laser diode in the optical block. Be sureground body and workbench, and use care theclothes do not touch the diode.1) After the connection, remo

17、ve solder shown inright figure.PICK-UP Assy P.C.BSolderRadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIRCharging voltage (V)Discharging Rated power (W)Parts number(C101, 102)resistor ()25-48100387-A00-247-09049-140220587-A00-232-090Note: The reference numbers (C101, C102) of the electrolytic

18、capacitors can change depending on the models. Be sure to check thereference numbers of the charging capacitors on schematic diagram before starting the discharging work.2. Check items before exchanging the MICROCOMPUTERBe sure to check the following items before exchanging the MICROCOMPUTER. Exchan

19、ge the MICROCOMPUTER after confirmingthat the MICROCOMPUTER is surely defective.2-1. Regarding the HOLD terminal of the MICROCOMPUTERWhen the HOLD terminal (INPUT) of the MICROCOMPUTER is “H” , the MICROCOMPUTER is judged to be operating correctly.When this terminal is “L” , the main power cannot be

20、 turned on. Therefore, be sure to check the terminal voltage of the HOLDterminal before exchange.When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has anyabnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HO

21、LD terminal to “L” .Good or no good judgement of the MICROCOMPUTER11111Turn on the AC main power.22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.33333When the HOLD terminal is “L” level, the abnormality detection circuit is judged t

22、o be working correctly and theMICROCOMPUTER is judged to be good.1. Forced discharge of electrolytic capacitor of power supply blockWhen repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged acrossthe electrolytic capacitors

23、(C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defectcan occur.In order to prevent the secondary trouble, perform the following measures before starting repair work.Discharge procedure11111Remove the AC power cord.22222Connect a discharging resi

24、stor at an end of lead wire thathas clips at both ends. Connect the other end of the leadwire to metal chassis.33333Contact the other end of the discharging resistor to thepositive (+) side (+VH) of C101. (For two seconds)44444Contact the same end of the discharging resistor as step33333 to the nega

25、tive (-) side (-VH) of C102 in the same way.(For two seconds)55555Check that voltage across C101 and C102 has decreasedto 1 V or less using a multimeter or an oscilloscope.Select a discharging resistor referring to the following table.Fig-1MAIN C.BD101C101C1022234RadioFans.CN 收音机爱 好者资料库 5 In such a

26、case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.2-2. Regarding resetThere are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC powercord is re-inserted, or the software reset (pressing the ST

27、OP key + POWER key) is performed.When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and toexchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or nogood of the MICROCOMPUTER.11111Re

28、move the AC power cord.22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER isgood.Note: The reference number or MICROCOMPUTER

29、pin number of transistor (Q110) and electrolytic capacitor (C113) can change dependingon the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.2-3. Confirmation of soldering state of MICROCOMPUTERCheck the soldering state of the MICROCOMPUTER in

30、 addition to the above described procedures. Be sure to exchange theMICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.Fig-2-2MICRO-COMPUTERMICROCOMPUTERFRONT C.BFRONT C.BVSSVDDC113*%C1131815Short with tweezers.RadioFans.CN 收音机爱 好者资料库

31、6 ELECTRICAL MAIN PARTS LISTDESCRIPTIONREF. NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO.IC 8A-NH7-601-010 C-IC,LC876572V-5R25 87-A21-355-010 IC,STK490-140 87-A21-398-010 IC,STK490-110 87-A20-914-010 IC,SPS-442-1-F 87-A20-783-040 C-IC,BA7762AFS 87-A21-577-040 C-IC,M61506FP 87-A21-021-040 C-

32、IC,BU2099FV 87-A21-097-040 C-IC,M62463AFP 87-070-289-040 C-IC,BU2092F 87-A21-015-040 C-IC,M62491FP 87-A20-561-040 C-IC,M65847AFP 87-A21-452-030 C-IC,BD3876KS2 87-A21-051-040 C-IC,BU9990-03FS 87-A21-560-010 IC,LA1844L-A 87-070-127-110 IC,LC72131D 87-020-454-010 IC,DN 6851TRANSISTOR 87-026-245-080 TR,

33、DTC114ES 87-026-609-080 TR,KTA1266GR 87-A30-198-080 TR,KTC3199GR 87-026-610-080 TR,KTC3198GR 87-A30-076-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-318-080 TR,CSA952K 89-213-702-010 TR,2SB1370E 87-A30-087-080 C-FET,2SK2158 87-A30-107-070 C-TR,CMBT5401 87-A30-468-080 C-TR,KRC102S-RTK 87-A30

34、-074-080 C-TR,RT1P 141C 87-A30-105-080 C-TR,RT1P 441C 87-A30-106-040 C-TR,CMBT5551 87-A30-190-080 TR,CC5551 87-A30-256-010 TR,2SD1933 87-A30-255-010 TR,2SB1342 87-A30-063-080 C-TR,KRA104S 87-A30-086-070 C-TR,CSD1306E 87-A30-269-040 C-FET,2SJ461-T1 87-A30-329-080 TR,CD1585BC 89-327-143-080 C-TR,2SC27

35、14O 87-A30-489-080 C-TR,KRA107S 87-A30-484-080 C-TR,KRA102S 89-503-602-080 C-FET,2SK360E 87-A30-234-080 TR,CSC4115BC 87-026-463-080 TR,2SA933SDIODE 87-A40-673-090 DIODE,D10XB20 87-A40-547-090 DIODE,D5SBA20 87-020-465-080 DIODE,1SS133 87-A40-553-080 DIODE,1N4003 LES 87-A40-784-080 ZENER,UZ39BSB 87-A4

36、0-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2836 87-A40-768-080 ZENER,UZ16BSA 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-535-080 DIODE,1N5393-GOODARK 87-A40-754-080 ZENER,UZ6.8BSC 87-A40-802-080 ZENER,UZ5.1BSC 87-A40-760-080 ZENER,UZ9.1BSA 8

37、7-A40-747-080 ZENER,UZ5.1BSB 87-A40-745-080 ZENER,UZ4.7BSA 87-A40-749-080 ZENER,UZ5.6BSB 87-017-149-080 ZENER,HZS6A2LMAIN C.B C003 87-012-368-080 C-CAP,S 0.1-50 Z F C004 87-012-368-080 C-CAP,S 0.1-50 Z F C021 87-016-658-000 CAP,E 4700-35 M SMG C022 87-016-658-000 CAP,E 4700-35 M SMG C025 87-010-406-

38、080 CAP,E 22-50 M 11L SME C026 87-010-406-080 CAP,E 22-50 M 11L SME C027 87-010-406-080 CAP,E 22-50 M 11L SME C028 87-010-406-080 CAP,E 22-50 M 11L SME C031 87-010-263-080 CAP,E 100-10 M 11L SME C032 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C034 87-010-247-080 CAP,E 100-50 M SME C035 87-010-260-080

39、CAP,E 47-25 M 11L SME C036 87-010-381-080 CAP,E 330-16 M SME C038 87-010-247-080 CAP,E 100-50 M SME C039 87-010-247-080 CAP,E 100-50 M SME C040 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C060 87-010-403-080 CAP,E 3.3-50 M 11L SME C080 87-010-401-080 CAP,E 1-50 M 11L SME C081 87-010-379-080 CAP,E 22-16

40、 M 11L SME C082 87-010-260-080 CAP,E 47-25 M 11L SME C115 87-010-546-080 CAP,E 0.33-50 M 11L SME C116 87-010-546-080 CAP,E 0.33-50 M 11L SME C152 87-010-260-080 CAP,E 47-25 M 11L SME C160 87-012-140-080 C-CAP,S 470P-50 J CH C161 87-010-176-080 C-CAP,S 680P-50 J SL C162 87-010-176-080 C-CAP,S 680P-50

41、 J SL C171 87-012-368-080 C-CAP,S 0.1-50 Z F C172 87-012-368-080 C-CAP,S 0.1-50 Z F C173 87-012-368-080 C-CAP,S 0.1-50 Z F C174 87-012-368-080 C-CAP,S 0.1-50 Z F C177 87-010-190-080 C-CAP,S 0.01-50 Z F C2012 C178 87-010-190-080 C-CAP,S 0.01-50 Z F C2012 C301 87-010-318-080 C-CAP,S 47P-50 J CH GRM C3

42、02 87-010-318-080 C-CAP,S 47P-50 J CH GRM C303 87-012-157-080 C-CAP,S 330P-50 J CH GRM C304 87-012-157-080 C-CAP,S 330P-50 J CH GRM C305 87-012-157-080 C-CAP,S 330P-50 J CH GRM C306 87-012-157-080 C-CAP,S 330P-50 J CH GRM C307 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C309 87-010-196-080 C-CAP,S 0.1-2

43、5 Z F C2012 C310 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C311 87-010-198-080 C-CAP,S 0.022-25 K B C2012 C312 87-010-198-080 C-CAP,S 0.022-25 K B C2012 C313 87-010-181-080 C-CAP,S 1800P-50 K B GRM C314 87-010-181-080 C-CAP,S 1800P-50 K B GRM C315 87-010-179-080 C-CAP,S 1200P-50 K B GRM C316 87-010-17

44、9-080 C-CAP,S 1200P-50 K B GRM C321 87-012-142-080 C-CAP,S 0.33-16 Z F GRM C322 87-012-142-080 C-CAP,S 0.33-16 Z F GRM C324 87-010-260-080 CAP,E 47-25 M 11L SME C325 87-010-370-080 CAP,E 330-6.3 M SME C327 87-010-404-080 CAP,E 4.7-50 M 11L SME C328 87-010-404-080 CAP,E 4.7-50 M 11L SME C332 87-010-1

45、96-080 C-CAP,S 0.1-25 Z F C2012 C335 87-010-401-080 CAP,E 1-50 M 11L SME C336 87-010-401-080 CAP,E 1-50 M 11L SME C337 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C339 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C340 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C351 87-012-140-080 C-CAP,S 470P-50 J CH C352 87-01

46、2-140-080 C-CAP,S 470P-50 J CH C354 87-010-175-080 C-CAP,S 560P-50 J SL C355 87-010-178-080 C-CAP,S 1000P-50 K B C2012 C356 87-010-260-080 CAP,E 47-25 M 11L SME C357 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C358 87-010-183-080 C-CAP,S 2700P-50 K B GRM C359 87-010-183-080 C-CAP,S 2700P-50 K B GRM C36

47、0 87-010-183-080 C-CAP,S 2700P-50 K B GRMRadioFans.CN 收音机爱 好者资料库 7 DESCRIPTIONREF. NO.KANRINO.PART NO.DESCRIPTIONREF. NO.KANRINO.PART NO. C370 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 C373 87-016-083-080 C-CAP,S 0.15-16 K R C374 87-016-083-080 C-CAP,S 0.15-16 K R C378 87-010-196-080 C-CAP,S 0.1-25 Z

48、F C2012 C379 87-010-382-080 CAP,E 22-25 M 11L SME C380 87-010-382-080 CAP,E 22-25 M 11L SME C381 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C382 87-010-312-080 C-CAP,S 15P-50 J CH GRM C383 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C384 87-010-402-080 CAP,E 2.2-50 M 11L SME C386 87-010-196-080 C-CAP,S 0

49、.1-25 Z F C2012 C387 87-012-145-080 C-CAP,S 270P-50 J CH GRM C388 87-012-156-080 C-CAP,S 220P-50 J CH GRM C391 87-010-319-080 C-CAP,S 56P-50 J CH C392 87-010-319-080 C-CAP,S 56P-50 J CH C393 87-010-319-080 C-CAP,S 56P-50 J CH C394 87-010-319-080 C-CAP,S 56P-50 J CH C401 87-010-176-080 C-CAP,S 680P-5

50、0 J SL C402 87-010-176-080 C-CAP,S 680P-50 J SL C403 87-010-958-080 C-CAP,S 0.01-25 J B C404 87-010-958-080 C-CAP,S 0.01-25 J B C405 87-010-958-080 C-CAP,S 0.01-25 J B C406 87-010-958-080 C-CAP,S 0.01-25 J B C407 87-010-401-080 CAP,E 1-50 M 11L SME C408 87-010-401-080 CAP,E 1-50 M 11L SME C409 87-01