JVC-FSSD990R-cs-sm 维修电路原理图.pdf

《JVC-FSSD990R-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-FSSD990R-cs-sm 维修电路原理图.pdf（31页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOMPACT COMPONENT SYSTEMNo.20923Mar. 2001COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.FS-SD550R / FS-SD770R / FS-SD990RContentsSafety PrecautionsImportant for laser productsPreventing static electricityDismantling and assembling the traverse unitDisassembly methodMaintenance of laser pi

2、ckupReplacement of laser pickupFlow of functional operation unit TOC readMethod of connecting treatment device wireDescription of major ICs 2-12-22-32-42-52-142-142-152-162-17REMOTE CONTROL DIMMERSLEEPDISPLAYFM MODEAHB PROCDPROGRAMDOORSLIDEAUTOPRESETREPEATRANDOMBASSTREBLECANCELUPSETDOWNMD/AUXFM / AM

3、VOLUMECDFADE MUTINGPTY/EONDISPLAY MODEFS-SD550RFS-SD770R, FS-SD990RREMOTE CONTROL DIMMERSLEEPDISPLAYFM MODEAHB PROCDPROGRAMDOORSLIDEAUTOPRESETREPEATRANDOMBASSTREBLECANCELUPSETDOWNMD/AUXFM / AMVOLUMECDFADE MUTINGPTY/EONDISPLAY MODEThe difference between FS-SD550R and FS-SD770R FS-SD990R is only the s

4、peaker systems.The difference between FS-SD770R and FS-SD990R is cabinets of the speaker.FS-SD550R FS-SD770R / FS-SD990RArea SuffixBEENU.KContinental EuropeNorthern EuropeCD-ROM No.SML200103These models not have adjustment.RadioFans.CN 收音机爱 好者资料库FS-SD550R/FS-SD770R/FS-SD990R1-21. This design of this

5、 product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits.

6、Services should be performed by qualified personnel only.2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufa

7、cture of responsibility for personal injury or property damage resulting therefrom.3. Many electrical and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessari

8、ly be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the schematics and by (

9、 ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety characteristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards.4. The leads in the products are routed and dres

10、sed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be conf

11、irmed that they have been returned to normal, after re-assembling.5. Leakage currnet check (Electrical shock hazard testing)After re-assembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone ja

12、ck, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check.Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal part

13、s of the cabinet , particularly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.)Alternate check methodPlug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or m

14、ore sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor between an exposed metal part and a known good earth ground.Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to eachexposed metal part, particu

15、larly any exposed metal part having a return path to the chassis, and meausre the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. voltage measured Any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1. This equipment has

16、 been designed and manufactured to meet international safety standards.2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.3. Repairs must be made in accordance with the relevant safety standards.4. It is essential that safety critical components ar

17、e replaced by approved parts.5. If mains voltage selector is provided, check setting for local voltage.Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE!Burrs formed during molding may be left over on some parts

18、 of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.RadioFans.CN 收音机爱 好者资料库FS-SD550R/FS-SD770R/FS-SD990R1-3Important for laser products1.CLASS 1 LASER PRODUCT2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid di

19、rect exposure to beam.3.CAUTION : There are no serviceable parts inside theLaser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions.4.CAUTION : The compact disc player uses invisible laser radiation and is equipped with safety switches which prevent emission

20、of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function.6.CAUTION : Use of controls, adjustments or performance of procedures other than those s

21、pecified herein may result in hazardous radiation exposure.VARNING : Osynlig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen.VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen.ADVARSEL : Usynlig laserstrling ved bning

22、, nr sikkerhedsafbrydere er ude af funktion. Undg udsttelse for strling.ADVARSEL : Usynlig laserstrling ved pning,nr sikkerhetsbryteren er avslott. unng utsettelse for strling.REPRODUCTION AND POSITION OF LABELSWARNING LABELDANGER : Invisible laser radiation when open and interlock or defeated.AVOID

23、 DIRECT EXPOSURE TO BEAM (e)VARNING : Osynlig laserstrlning r denna del r ppnad och sprren r urkopplad. Betrakta ej strlen. (s)VARO : Avattaessa ja suojalukitus ohitettaessa olet alttiina nkymttmlle lasersteilylle.l katso steeseen. (d)ADVARSEL :Usynlig laserstrling ved bning , nr sikkerhedsafbrydere

24、 er ude af funktion. Undg udsttelse for strling. (f)CLASS 1LASER PRODUCT!CAUTIONPlease use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck.FS-SD550R/FS-SD770R/FS-SD990R1-4Preventing static electricityElectrostatic discharge (ESD), which occurs when

25、static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.1. Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pi

26、ckup (laser diode) in devices such as DVD players. Be careful to use proper grounding in the area where repairs are being performed. 1.1.1. Ground the workbench1. Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit

27、 (optical pickup) on it.1.1.2. Ground yourself1. Use an anti-static wrist strap to release any static electricity built up in your body. 1.1.3. Handling the optical pickup1. In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optica

28、l pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)2. Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.2. Handling the traverse

29、unit (optical pickup)1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. 2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the te

30、xt. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. 3. Handle the flexible cable carefully as it may break when subjected to strong force. 4. It is not possible to adjust the semi-fixed resistor that adjusts the

31、laser power. Do not turn itConductive material (conductive sheet) or iron plate(caption)Anti-static wrist strapFS-SD550R/FS-SD770R/FS-SD990R1-5 Dismantling and assembling the traverse unitNotice regarding replacement of optical pickupElectrostatic discharge (ESD), which occurs when static electricit

32、y stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs to the optical pickup or connected devices. 1. Do not touch the area around the laser diode and actuator.2. Do not check the laser di

33、ode using a tester, as the diode may easily be destroyed.3. It is recommended that you use a grounded soldering iron when shorting or removing the laser diode. Recommended soldering iron: HAKKO ESD-compatible product4. Solder the land on the optical pickups flexible cable. Note : Short the land afte

34、r shorting the terminal on the flexible cable using a clip, etc., when using an ungrounded soldering iron. Note : After shorting the laser diode according to the procedure above, remove the solder according to the text explanation. ShortingFlexible cable KSM-900AAHSub board(Reverse side)FS-SD550R/FS

35、-SD770R/FS-SD990R1-6Piro to performing the following procedure, remove the CD door.Remove the ten screws B and the five screws C attaching the rear cover on the back of the body.1.Removing the rear cover (See Fig.2)Remove the four screws A attaching the CD door on the upper side of the body.1.Removi

36、ng the CD door (See Fig.1)Prior to performing the following procedure, remove the CD door, the rear cover.Remove the four screws D attaching the side covers on the bottom of the body.Move the left cover backward and remove outward. Also remove the right cover in the same way.1.2.Removing the right a

37、nd left covers (See Fig.3)Disassembly methodFig.1Fig.2Fig.3BBBBBBCCCRear coverDDRight coverLeft coverBottomCD doorAAFS-SD550R/FS-SD770R/FS-SD990R1-7Prior to performing the following procedure, remove the CD door, the rear cover and the side covers.Remove the three screws E on the bottom of the body.

38、Release two joints a and two joints b on both sides of the body using a screwdriver and remove the front panel assembly toward the front.1.2.Removing the front panel assembly (See Fig.4 to 6)Prior to performing the following procedure, remove the CD door, the rear cover, the side covers and the fron

39、t panel assembly.Disconnect the card wire from connector CN104 and CN105 of the main board in the front part of the body. Disconnect the card wire from CN101 of the main board on the right side, and the wire from CN705 and CN of the CD mechanism base assembly respectively.Remove the four screws F at

40、taching the CD mechanism base assembly on the upper side of the body. Remove the screw I attaching the earth terminal on the right side.1.2.Removing the CD mechanism base assembly (See Fig.7 to 14)Fig.4Fig.6Fig.5EFront panel assembly(Left side)(Right side)Front panel assemblyJoints aJoints bBottomFi

41、g.7Fig.8FFCD mechanism base assemblyCD mechanism base assemblyMain bardCN105CN104Front panel assemblyFFS-SD550R/FS-SD770R/FS-SD990R1-8Remove the screw G attaching the power amplifier board on the back of the body. Disconnect the wire from connector CN301 and pull the power amplifier board fully outw

42、ard.Raise the right and left door arms by turning the gear a in the rear of the power amplifier board.After the CD mechanism base assembly is detached from the door arms, pull the CD mechanism base assembly toward the front and disconnect the wire from connector CN804 on the left side of the door ar

43、m board.Pull out the CD mechanism base assembly toward the front.3.4.5.6.Fig.9Fig.10Fig.11FICD mechanism base assemblyMain boardCN101CN708FCD mechanism base assemblyCN804CD mechanism base assemblyCN301GPower amplifier boardFig.13Gear aFig.12Fig.14CD mechanism base assemblyPower amplifier boardDoor a

44、rmDoor armIGear aCD mechanism base assemblyDoor arm board (L)CN804CN705FS-SD550R/FS-SD770R/FS-SD990R1-9Prior to performing the following procedure, remove the rear cover, the side covers, the front panel assembly and the CD mechanism base assembly.In case that the upper parts of the door arms attach

45、ed to the CD door are not level, let down them to the level position by turning the gear a in the direction of the arrow.1.Removing the door arm assembly / the door arm board (R) and (L)(See Fig.15 to 20)When the door arms incline, the door arm assembly and the door arm board (R) and (L) may not be

46、removed.ATTENTION: Remove the four screws H on the upper side and the one screw I on the left side of the body.Remove the four screws J attaching the door arm board (L) and (R) on both sides of the door arm assembly.2.3.Fig.15Fig.16Fig.18Fig.20Fig.17Fig.19Door armDoor arm board (L)Door armDoor arm b

47、oard (R)Door arms (Attached to the CD door)HHDoor arm assemblyDoor arm assemblyJJIDoor arm board (L)Door arm assemblyJJDoor arm board (R)Fan motorFS-SD550R/FS-SD770R/FS-SD990R1-10Prior to performing the following procedure, remove the CD mechanism base assembly.Disconnect the wires from connector CN

48、102 and CN193 on the main board and release them from the cord stopper respectively.Remove the two screws K and the two screws L attaching the heat sink and the power amplifier board.1.2.Removing the power amplifier board(See Fig.21 and 22)Prior to performing the following procedure, remove the CD m

49、echanism base assembly.Disconnect the wires from connector CN191 and CN192 on the main board and release them from the cord stopper respectively.Remove the four screws M attaching the transformer assembly.1.2.Removing the transformer assembly (See Fig.21)Prior to performing the following procedure,

50、remove the CD mechanism base assembly and the door arm assembly.Disconnect the wires from connector CN106 on the main board and release it from the cord stopper.Remove the three screws N attaching the gear motor assembly. Remove the gear motor assembly with the gear motor stopper.Remove the belt fro