《JVC-DXU6-cs-sm 维修电路原理图.pdf》由会员分享,可在线阅读,更多相关《JVC-DXU6-cs-sm 维修电路原理图.pdf(103页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUALCOPYRIGHT 2008 Victor Company of Japan, LimitedNo.MB6162008/4COMPACT COMPONENT SYSTEMMB61620084 SERVICE MANUALDX-U10A, DX-U10US, DX-U10UX, DX-U10UG,DX-U10UN, DX-U8US, DX-U8UX, DX-U8UG,DX-U8UN, DX-U6US, DX-U6UX, DX-U6UG,DX-U6UN, DX-U10UHCOPYRIGHT 2008 Victor Company of Japan, LimitedLea
2、d free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)TABLE OF CONTENTS1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3、. . . . . . . . . . . . . . . . . . . . . . 1-42SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-73DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4、 . . . . . . . . . . . . . . . . . . . . . 1-84ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-345TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5、 . . . . . . . . . . . . . . . . . . . . . . . . . 1-35SUPER VIDEOSUPER VIDEOCA-DXU6SP-DXU6FSP-DXU6FSP-DXU10WCA-DXU8SP-DXU10FSP-DXU10FSP-DXU10WSP-DXU8SSP-DXU8SSP-DXU10C CA-DXU10 SP-DXU10F SP-DXU10F SP-DXU10W SP-DXU10W SP-DXU10S SP-DXU10S SP-DXU10CRadioFans.CN 收音机爱 好者资料库1-2 (No.MB616)SPECIFICATIONDX-
6、U10/DX-U8Measured at 1 kHz, with tape recording signal 400 mVDesign and specifications are subject to change without notice.Amplifier sectionOutput PowerFRONT SPEAKERS150 W per channel, min. RMS, driven into 4 at 1 kHz with no more than 10% total harmonic distortion.CENTER SPEAKERCA-DXU10 140 W per
7、channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion.CA-DXU850 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion.SURROUND SPEAKERS CA-DXU10 130 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% tot
8、al harmonic distortion.CA-DXU850 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion.SUBWOOFERS150 W, min. RMS, driven into 4 at 63 Hz with no more than 10% total harmonic distortion.Digital outputOPTICAL DIGITAL OUTPUT-21 dBm to -15 dBm (660 nm 30 nm)Digi
9、tal inputUSB memoryAudio input sensitivity/ImpedanceAUX(STEREO)400 mV/47 kMIC1/MIC23.0 mV/50 kVIDEO OUTColor systemPAL/PAL PROG/NTSC/NTSC PROG selectableVIDEO (composite)1 V(p-p)/75 S-VIDEOY (luminance) : 1 V(p-p)/75 C (chrominance, burst) : PAL : 0.3 V(p-p)/75 C (chrominance, burst) : NTSC : 0.286
10、V(p-p)/75 COMPONENT(Interlace/Progressive)(Y) : 1 V(p-p)/75 (PB/PR) : 0.7 V(p-p)/75 Speaker Terminals4 - 16 (front speakers/subwoofers)6 - 16 (surround/center speakers)Tuner sectionFM tuning range87.50 MHz - 108.00 MHzAM (MW) tuning range531 kHz - 1 710 kHz (at 9 kHz)530 kHz - 1 710 kHz (at 10 kHz)A
11、M (MW) tuning range for Saudi Arabia531 kHz to 1 602 kHz (9 kHz)530 kHz to 1 600 kHz (10 kHz)Disc/file player section Region codesMiddle East: 2South East Asia: 3Central and South America, Australia: 4Playable discDVD Video/DVD Audio/CD/VCD/SVCDCD-R/CD-RW (CD/VCD/SVCD/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/
12、ASF/DivX format)CD-ROM (MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)DVD-R/-RW (DVD-VR/DVD Video/DVD Audio/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)+R/+RW (DVD Video/DVD Audio/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)DVD-ROM (DVD Video/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)Pla
13、yable fileMP3, WMA, WAV, JPEG, MPEG-1, MPEG-2, ASF, DivX for-matDynamic range80 dBHorizontal resolution500 linesWow and flutterImmeasurableUSB storage sectionUSB specificationCompatible with USB 2.0 Full SpeedCompatible deviceMass Storage ClassCompatible file systemFAT16, FAT32Bus power supply5 V /
14、500 mACassette deck section Frequency response: Normal (type I)50 Hz - 14 000 HzWow and flutter0.15% (WRMS)GeneralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240 V , (adjustable with the voltage selector), 50 Hz / 60 HzPower requirement: For AustraliaAC 240 V , 50 HzPower consump
15、tionCA-DXU10300 W (at operation) / 22 W (on standby)CA-DXU8270 W (at operation) / 21 W (on standby)Dimensions (W/H/D) (approx.)185 mm 460 mm 370 mmMass (approx.)CA-DXU1011.5 kgCA-DXU811.4 kgRadioFans.CN 收音机爱 好者资料库(No.MB616)1-3DX-U6Measured at 1 kHz, with tape recording signal 400 mVDesign and specif
16、ications are subject to change without notice.Amplifier sectionOutput PowerFRONT SPEAKERS150 W per channel, min. RMS, driven into 4 at 1 kHz with no more than 10% total harmonic distortion.SUBWOOFER150 W, min. RMS, driven into 4 at 63 Hz with no more than 10% total harmonic distortion.Digital output
17、OPTICAL DIGITAL OUTPUT -21 dBm to -15 dBm (660 nm 30 nm)Digital inputUSB memoryAudio input sensitivity/ImpedanceAUX400 mV/47 kMIC1/MIC23.0 mV/50 kVIDEO OUTColor systemPAL/PAL PROG/NTSC/NTSC PROG selectableVIDEO (composite)1 V(p-p)/75 S-VIDEOY (luminance) : 1 V(p-p)/75 C (chrominance, burst) : PAL :
18、0.3 V(p-p)/75 C (chrominance, burst) : NTSC : 0.286 V(p-p)/75 COMPONENT(Interlace/Progressive)(Y) : 1 V(p-p)/75 (PB/PR) : 0.7 V(p-p)/75 Speaker Terminals4 - 16 (main speakers/subwoofer)16 - 32 (matrix surround speakers)Tuner sectionFM tuning range87.50 MHz - 108.00 MHzAM (MW) tuning range531 kHz - 1
19、 710 kHz (at 9 kHz)530 kHz - 1 710 kHz (at 10 kHz)AM (MW) tuning range: For Saudi Arabia531 kHz to 1 602 kHz (9 kHz)530 kHz to 1 600 kHz (10 kHz)Disc/file player section Region codesMiddle East: 2South East Asia: 3Central and South America, Australia: 4Playable discDVD Video/DVD Audio/CD/VCD/SVCDCD-
20、R/CD-RW (CD/VCD/SVCD/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)CD-ROM (MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX for-mat)DVD-R/-RW (DVD-VR/DVD Video/DVD Audio/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)+R/+RW (DVD Video/DVD Audio/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)DVD-ROM (DVD Vid
21、eo/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/DivX format)Playable fileMP3, WMA, WAV, JPEG, MPEG-1, MPEG-2, ASF, DivX formatDynamic range80 dBHorizontal resolution500 linesWow and flutterImmeasurableUSB storage sectionUSB specificationCompatible with USB 2.0 Full SpeedCompatible deviceMass Storage ClassComp
22、atible file systemFAT16, FAT32Bus power supply5 V / 500 mACassette deck section Frequency response: Normal (type I)50 Hz - 14 000 HzWow and flutter0.15% (WRMS)GeneralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240 V , (adjustable with the voltage selector), 50 Hz / 60 HzPower req
23、uirement: For AustraliaAC 240 V , 50 HzPower consumption200 W (at operation)19 W (on standby)Dimensions (W/H/D) (approx.)185 mm 460 mm 370 mmMass (approx.)10.5 kg1-4 (No.MB616)SECTION 1PRECAUTION1.1Safety Precautions(1) This design of this product contains special hardware andmany circuits and compo
24、nents specially for safety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufacturer. Replacement parts must be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Al
25、terations of the design or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or additions will voidthe manufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resu
26、lting therefrom.(3) Many electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not evident from visual inspection nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher vo
27、ltage, watt-age, etc. Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical components having such featuresare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitute
28、replacement which does not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create shock, fire, orother hazards.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated
29、 fromlive parts, high temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the original lead routingand dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leak
30、age shock hazard testingAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, knobs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shoc
31、k.Do notuse a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using aLeakage Current Tester, measure the leakage currentfrom each exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known g
32、ood earth ground. Any leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC voltmeter having, 1,000 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor
33、 between an ex-posed metal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection to each exposed metalpart, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor
34、. Now, reverse the plug in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). 1.2Warning(1) This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility
35、 of the repairer to ensure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is essential that safety critical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.
36、3CautionBurrs formed during molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair of this system.1.4Critical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagra
37、ms, the parts that areprinted over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the mark nearby are criticalfor safety. When replacing them, be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and
38、C version)Good earth groundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE(No.MB616)1-51.5Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is dis
39、charged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.5.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be c
40、areful to use proper grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static
41、wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement opticalpickup are shorted. After replacement, return the shorted parts to their
42、 original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easilydestroy the laser diode. 1.6Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to s
43、trong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to thereplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful no
44、t to take too long atime when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.7Attention when traverse unit is decomposed*Pl
45、ease refer to Disassembly method in the text for the pickup unit. Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wireis disconnected without applying solder, the pickup may be destroyed by static electricity.) In the as
46、sembly, be sure to remove solder from the short land sections after connecting the card wire.1MConductive material(conductive sheet) or iron palate(caption)Anti-static wrist strapDVD changer mechanism assemblySwitch boardDVD traverse mechanism assemblyDVD servo board1-6 (No.MB616)1.8Important for la
47、ser products1.CLASS 1 LASER PRODUCT 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible
48、laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have fail
49、ed or are defeated. It is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTI
50、ON AND POSITION OF LABELS and PRINT!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck. WARNING LABEL and PRINT(No.MB616)1-7SECTION 2SPECIFIC SERVICE INSTRUCTIONSThis service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.1-8 (No.MB6