JVC-MXDK11-cs-sm 维修电路原理图.pdf

《JVC-MXDK11-cs-sm 维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《JVC-MXDK11-cs-sm 维修电路原理图.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUALCOPYRIGHT 2007 Victor Company of Japan, LimitedNo.MB5982007/2COMPACT COMPONENT SYSTEMMB59820072 SERVICE MANUALMX-DK11A,MX-DK11UW,MX-DK11UX,MX-DK11UY,MX-DK11UG,MX-DK11UNCOPYRIGHT 2007 Victor Company of Japan, LimitedLead free solder used in the board (material : Sn-Ag-Cu, melting point

2、: 219 Centigrade)Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)TABLE OF CONTENTS1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32SPECIFIC SERVICE INS

3、TRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-63DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-294ADJUSTMENT . . . . . .

4、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-295TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29CA-MXDK11SP-MX

5、DK11SP-MXDK11RadioFans.CN 收音机爱 好者资料库1-2 (No.MB598)SPECIFICATION*1: Measured at 1 kHz, with tape recording signal 400 mV. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Lab-oratories. DTS is a registered trademark of DTS, Inc. and

6、 DTS 2.0+Digital Out is a trademark of DTS, Inc. Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. This product incorporates copyright protection technology that is protected by U.S. patents and other inte

7、llectual property rights.Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewinguses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Design and specifications are subject to c

8、hange without notice.Amplifier sectionOutput Power90 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion.Digital outputOPTICAL DIGITAL OUTPUT : -21 dBm to -15 dBm (660 nm 30 nm)Audio input sensitivity/Impedance *1AUX : 400 mV/47 kMIC : 3.0 mV/50 kVIDEO OUT

9、Color systemNTSC/PAL selectableVIDEO (composite)1 V(p-p)/75 S-VIDEOY (luminance) : 1 V(p-p)/75 C (chrominance, burst) : 0.286 V(p-p)/75 Speaker Terminals6 - 16 Tuner sectionFM tuning range87.50 MHz - 108.00 MHzAM (MW) tuning range531 kHz - 1 710 kHz (at 9 kHz)530 kHz - 1 710 kHz (at 10 kHz)For Saudi

10、 Arabia only531 kHz - 1 602 kHz (at 9 kHz)530 kHz - 1 600 kHz (at 10 kHz)Disc player sectionPlayable discDVD Video/CD/VCD/SVCDCD-R/-RW/-ROM(CD/VCD/SVCD/MP3/WMA/JPEG/MPEG-1/MPEG-2 format)DVD-R/-RW(DVD Video/DVD Video Recording (VR)/MP3/WMA/JPEG/MPEG-1/MPEG-2 format)+R/+RW(DVD Video format)Dynamic ran

11、ge90 dBHorizontal resolution500 linesWow and flutterImmeasurableCassette deck section Frequency response Normal (type l) 50 Hz - 14 000 HzWow and flutter0.15% (WRMS)GeneralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240 V , (adjustable with the voltage selector), 50 Hz / 60 HzPow

12、er consumptionat operation: 95 W, on standby: 17 WDimensions (approx.)265 mm 337 mm 370 mm (W/H/D)Mass (approx.)7.9 kgRadioFans.CN 收音机爱 好者资料库(No.MB598)1-3SECTION 1PRECAUTION1.1Safety Precautions(1) This design of this product contains special hardware andmany circuits and components specially for sa

13、fety purpos-es. For continued protection, no changes should be madeto the original design unless authorized in writing by themanufacturer. Replacement parts must be identical tothose used in the original circuits. Services should be per-formed by qualified personnel only.(2) Alterations of the desig

14、n or circuitry of the product shouldnot be made. Any design alterations of the product shouldnot be made. Any design alterations or additions will voidthe manufacturers warranty and will further relieve themanufacture of responsibility for personal injury or propertydamage resulting therefrom.(3) Ma

15、ny electrical and mechanical parts in the products havespecial safety-related characteristics. These characteris-tics are often not evident from visual inspection nor can theprotection afforded by them necessarily be obtained by us-ing replacement components rated for higher voltage, watt-age, etc.

16、Replacement parts which have these specialsafety characteristics are identified in the Parts List of Ser-vice Manual. Electrical components having such featuresare identified by shading on the schematics and by ( ) onthe Parts List in the Service Manual. The use of a substitutereplacement which does

17、 not have the same safety charac-teristics as the recommended replacement parts shown inthe Parts List of Service Manual may create shock, fire, orother hazards.(4) The leads in the products are routed and dressed with ties,clamps, tubings, barriers and the like to be separated fromlive parts, high

18、temperature parts, moving parts and/orsharp edges for the prevention of electric shock and firehazard. When service is required, the original lead routingand dress should be observed, and it should be confirmedthat they have been returned to normal, after reassem-bling.(5) Leakage shock hazard testi

19、ngAfter reassembling the product, always perform an isola-tion check on the exposed metal parts of the product (an-tenna terminals, knobs, metal cabinet, screw heads,headphone jack, control shafts, etc.) to be sure the productis safe to operate without danger of electrical shock.Do notuse a line iso

20、lation transformer during this check. Plug the AC line cord directly into the AC outlet. Using aLeakage Current Tester, measure the leakage currentfrom each exposed metal parts of the cabinet, particular-ly any exposed metal part having a return path to thechassis, to a known good earth ground. Any

21、leakage cur-rent must not exceed 0.5mA AC (r.m.s.). Alternate check methodPlug the AC line cord directly into the AC outlet. Use anAC voltmeter having, 1,000 per volt or more sensitivityin the following manner. Connect a 1,500 10W resistorparalleled by a 0.15F AC-type capacitor between an ex-posed m

22、etal part and a known good earth ground.Measure the AC voltage across the resistor with the ACvoltmeter. Move the resistor connection to each exposed metalpart, particularly any exposed metal part having a returnpath to the chassis, and measure the AC voltage acrossthe resistor. Now, reverse the plu

23、g in the AC outlet andrepeat each measurement. Voltage measured any mustnot exceed 0.75 V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). 1.2Warning(1) This equipment has been designed and manufactured tomeet international safety standards.(2) It is the legal responsibility of the repairer to en

24、sure thatthese safety standards are maintained.(3) Repairs must be made in accordance with the relevantsafety standards.(4) It is essential that safety critical components are replacedby approved parts.(5) If mains voltage selector is provided, check setting for localvoltage.1.3CautionBurrs formed d

25、uring molding may be left over on some partsof the chassis. Therefore, pay attention to such burrs in the case of pre-forming repair of this system.1.4Critical parts for safetyIn regard with component parts appearing on the silk-screenprinted side (parts side) of the PWB diagrams, the parts that are

26、printed over with black such as the resistor ( ), diode ( )and ICP ( ) or identified by the mark nearby are criticalfor safety. When replacing them, be sure to use the parts of thesame type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version)Good earth g

27、roundPlace this probe on each exposedmetal part.AC VOLTMETER(Having 1000 ohms/volts,or more sensitivity)1500 10W0.15 F AC TYPE1-4 (No.MB598)1.5Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy

28、the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.1.5.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper

29、grounding in the area where repairs are being performed. (1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.(2) Ground yourselfUse an anti-static wrist strap to releas

30、e any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement opticalpickup are shorted. After replacement, return the shorted parts to their original condition.

31、(Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easilydestroy the laser diode. 1.6Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it i

32、s a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to thereplacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long at

33、ime when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.1.7Attention when traverse unit is decomposed*Please refer to Disasse

34、mbly method in the text for the pickup unit. Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wireis disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to re

35、move solder from the short land sections after connecting the card wire.1MConductive material(conductive sheet) or iron palate(caption)Anti-static wrist strapDVD changer mechanism assemblySwitch boardDVD traverse mechanism assemblyDVD servo board(No.MB598)1-51.8Important for laser products1.CLASS 1

36、LASER PRODUCT 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation when o

37、pen and inter lock failed or defeated. Avoid direct exposure to beam.4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It

38、 is dangerous to defeat the safety switches.5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LAB

39、ELS and PRINT!Please use enough caution not to see the beam directly or touch it in case of an adjustment or operationcheck. WARNING LABEL and PRINT1-6 (No.MB598)SECTION 2SPECIFIC SERVICE INSTRUCTIONSPlease use the MX-DK1US service manual (No.MB515) excluding the published content as follows.The use

40、 number has changed when a part number of the reference origin and this part number are the same.Parts list (General assembly) P3-4 Block No.M1MMMX-DK11AMX-DK11UWItemParts nameParts numberQtyMX-DK1USMX-DK11A1FRONT PANEL ASSYGV10328-001AGV10328-038A14FUNCTION BUTTONGV20418-002AGV20418-003A17FRONT LEN

41、SGV10319-001AGV10319-017A18VOLUME KNOBGV30875-001AGV30875-007A19V.ORNAMENT ASSYGV30894-001AGV30894-004A111MIC.KNOBGV40083-004A-014SPACERGV30349-068A-024TAP SCREWQYSBSF3010ZAQYSBSF3010ZA529SPACERGV30349-046A-031HEAT SINKGV30879-003AGV31012-001A132SCREWQYSBSG3016EAQYSBSG3016EA135SCREWQYSBSG3010EA-039S

42、CREWQYSBSF3010ZA-040METAL COVERGV10217-007A/S/GV10217-015A/S/144REAR PANELGV10324-004AGV10324-047A147TUNERQAU0412-001QAU0492-001150TAP SCREWQYSBSGY3008EA-058TAP SCREWQYSDSG3006NAQYSDSG3008NA263POWER CORD(EU)QMPK200-200-JDQMPG150-244-JC164POWER TRANSQQT0515-001QQT0534-001166FFC WIREQUQU12-1911AJ-EQUQ

43、U12-1913AJ-E167FFC WIREQUQU12-1915BJ-EQUQU12-1921BJ-E168FFC WIREQUQU12-0915BJ-EQUQU12-0921BJ-E169FFC WIREQUR110-2520AJ-EQUR110-0532BJ-E170FFC WIREQUR110-0515AJ-EQUR110-2517AJ-E171FFC WIREQUR110-0532BJ-EQUR110-0513AJ-E178SPACERGV30349-048A-0ItemParts nameParts numberQtyMX-DK1USMX-DK11UW1FRONT PANEL A

44、SSYGV10328-001AGV10328-037A14FUNCTION BUTTONGV20418-002AGV20418-003A17FRONT LENSGV10319-001AGV10319-017A18VOLUME KNOBGV30875-001AGV30875-007A19V.ORNAMENT ASSYGV30894-001AGV30894-004A111MIC.KNOBGV40083-004AGV40083-006A114SPACERGV30349-068A-024TAP SCREWQYSBSF3010ZAQYSBSF3010ZA529SPACERGV30349-046A-031

45、HEAT SINKGV30879-003AGV31012-001A1(No.MB598)1-7MX-DK11UX/UG32SCREWQYSBSG3016EAQYSBSG3016EA135SCREWQYSBSG3010EA-039SCREWQYSBSF3010ZA-040METAL COVERGV10217-007A/S/GV10217-015A/S/144REAR PANELGV10324-004AGV10324-045A147TUNERQAU0412-001QAU0492-001158TAP SCREWQYSDSG3006NAQYSDSG3008NA264POWER TRANSQQT0515

46、-001QQT0534-001166FFC WIREQUQU12-1911AJ-EQUQU12-1913AJ-E167FFC WIREQUQU12-1915BJ-EQUQU12-1921BJ-E168FFC WIREQUQU12-0915BJ-EQUQU12-0921BJ-E169FFC WIREQUR110-2520AJ-EQUR110-0532BJ-E170FFC WIREQUR110-0515AJ-EQUR110-2517AJ-E171FFC WIREQUR110-0532BJ-EQUR110-0513AJ-E178SPACERGV30349-048A-0ItemParts namePa

47、rts numberQtyMX-DK1USMX-DK11UX/UG1FRONT PANEL ASSYGV10328-001AGV10328-037A14FUNCTION BUTTONGV20418-002AGV20418-003A17FRONT LENSGV10319-001AGV10319-017A18VOLUME KNOBGV30875-001AGV30875-007A19V.ORNAMENT ASSYGV30894-001AGV30894-004A111MIC.KNOBGV40083-004AGV40083-006A114SPACERGV30349-068A-024TAP SCREWQY

48、SBSF3010ZAQYSBSF3010ZA529SPACERGV30349-046A-031HEAT SINKGV30879-003AGV31012-001A132SCREWQYSBSG3016EAQYSBSG3016EA135SCREWQYSBSG3010EA-039SCREWQYSBSF3010ZA-040METAL COVERGV10217-007A/S/GV10217-015A/S/144REAR PANELGV10324-004AGV10324-046A147TUNERQAU0412-001QAU0492-001158TAP SCREWQYSDSG3006NAQYSDSG3008N

49、A264POWER TRANSQQT0515-001QQT0534-001166FFC WIREQUQU12-1911AJ-EQUQU12-1913AJ-E167FFC WIREQUQU12-1915BJ-EQUQU12-1921BJ-E168FFC WIREQUQU12-0915BJ-EQUQU12-0921BJ-E169FFC WIREQUR110-2520AJ-EQUR110-0532BJ-E170FFC WIREQUR110-0515AJ-EQUR110-2517AJ-E171FFC WIREQUR110-0532BJ-EQUR110-0513AJ-E178SPACERGV30349-

50、048A-0ItemParts nameParts numberQtyMX-DK1USMX-DK11UW1-8 (No.MB598)MX-DK11UYMX-DK11UNItemParts nameParts numberQtyMX-DK1USMX-DK11UY1FRONT PANEL ASSYGV10328-001AGV10328-038A14FUNCTION BUTTONGV20418-002AGV20418-003A17FRONT LENSGV10319-001AGV10319-017A18VOLUME KNOBGV30875-001AGV30875-007A19V.ORNAMENT AS